40266350
for procurement of furniture for the newly constructed new administrative building of district magistrate jhargram , reception table 1500 ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelvess , size:1981h x 916w x 486d1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with one drawer unit , size:1350 x 750 x 750 ( enzo table 4525 size shall be1350 width mmx 750 depth mmx 750 height mm .the table top shall be made of pre laminated particle board with 18 mm thick and 15 mm thick understructure covered with pvc lipping .there shall be locking provided for top drawers only , attractive black colour handles for all drawers plus only one colour is available beech.it shall have 1 drawer attachment and hdu attachment. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and must have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , sloted angel rack ( load bearing members of the system are made out of high strength hr steel having properties equivalent to grades specified by is 5986:2002 / is 2062:2006 the different types of material used for load bearing members such as uprights and beams are: steel type: fe 410 / equivalent ( or ) is:2062 e 250 / equivalent to is: 513d minimum yield strength: 255 mpa in addition to high strength, the raw material used for structural load bearing members possesses adequate ductility to ensure toughness. ) , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:1650x750x750 ( trident middle main deskwith eru ( rhs ) size shall be1650 width x 700 depth x 743 height ( main desk ) 1000 widthx 450depthx 743 height ( eru ) .top shall be of 18 mm thickness made of plt board with 2 mm edge banding. wenge and savannah maple plt board shall be used. the understructure shall be in pre laminated panels made with plt boards . 2 drawerand 3 drawer storage units with different combinations to support tops made with 18 mm plt boards of different colours.modesty and back panels made with 18 mm plt boards. the pedestals / storages shall be fitted with necessary locks. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene.4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , file storage ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , 3 seater visitor chair without arms ( 1 ) seat shell : the seat shell should bea welded assembly of seat, back and side frame. the seat and back should bemade of 0.12±0.013cm thk cr steel sheet with oblong perforations.they should bewelded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowder coated ( dft 40 60 microns ) . the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. seat size : 47.8 cm ( w ) x 44.6 cm ( d ) back size : 41.6 cm ( w ) x 23.0 cm ( h ) 2 ) understructure assembly: understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should bepowder coated ( dft 40 60 microns ) .the leg assembly should befitted with shoes and levellers in nylon. the leg structure should bedesigned with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould beof uneven flooring.connecting beam should befitted with snap locking end cap.lt also aids in side by side understructure alignment. 3 ) arm rest assembly: armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should bemade up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should bepowder coated ( dft 40 60 microns ) . armrest pad should beinjection molded in nylon and should befitted onto the armrest frame. 4 ) side table assembly: it should bea welded structure assembly made of 0.12±0.013cm thk cr steel sheet with oblong perforations which should bewelded to side strip of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowdercoated ( dft 40 60 microns ) and fitted to understructure assembly. side table size: 20.0 cm ( w ) x 37.2 cm ( d ) all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and must have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chairs ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal should be a.back size 47.5 cm. ( w ) x58.0 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. 3.armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. tubular frame: the powder coated ( dft 40 60 microns ) tubular frame should becantilever type & made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. m.s. er.w. tube. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , periodical display rack ( overall dimensions of all steel periodical displayrack shall be 900mm ( w ) x450mm ( d ) x1830mm ( h ) . rigid knockdown construction , panels shall be made from crca 0.6 mm thick and front frame shall be made from crca 0.8 mm thick . crca d grade as per is 513 . there shall be 5 level racks , display tray shall be suitable for fullscape size magazines, periodicals, aesthetically appealing metal tray at an angle for easy viewing . receding facility to access the storage behind . sliding on plastic rollers . behind storage shelving each of 5 level has a behind storage shelf . uniformly distributed load capacity per each shelf is 40 kg . leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , 3 seater visitor chair without arms ( 1 ) seat shell : the seat shell should bea welded assembly of seat, back and side frame. the seat and back should bemade of 0.12±0.013cm thk cr steel sheet with oblong perforations.they should bewelded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowder coated ( dft 40 60 microns ) . the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. seat size : 47.8 cm ( w ) x 44.6 cm ( d ) back size : 41.6 cm ( w ) x 23.0 cm ( h ) 2 ) understructure assembly: understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should bepowder coated ( dft 40 60 microns ) .the leg assembly should befitted with shoes and levellers in nylon. the leg structure should bedesigned with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould beof uneven flooring.connecting beam should befitted with snap locking end cap.lt also aids in side by side understructure alignment. 3 ) arm rest assembly: armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should bemade up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should bepowder coated ( dft 40 60 microns ) . armrest pad should beinjection molded in nylon and should befitted onto the armrest frame. 4 ) side table assembly: it should bea welded structure assembly made of 0.12±0.013cm thk cr steel sheet with oblong perforations which should bewelded to side strip of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowdercoated ( dft 40 60 microns ) and fitted to understructure assembly. side table size: 20.0 cm ( w ) x 37.2 cm ( d ) all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and must have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , sofa 3 str ( providing, supplying and placing of three seater sofa .overall size :width: 171cm depth : 86cm height : 77cmseating height : 39cmframe material : tropical solid wood , seat foam : polyurethane foam with recron layer. foam density : 18 kg / cubic cm. back foam : polyurethane foam with silicon fill at arms. foam density : 22 kg / cubic cm all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with one drawer unit , size:1500 x 750 x 750 ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chairs ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office storage ( glass door storwel shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the glass door storwel shall have a brass handle and a 2 way locking mechanism with shooting bolt .it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene.4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves, size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves, size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table & drawer, size: 2350x2350x750 ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chair plastic ( 1 ) seat / back: the seat and back should bemade up of injection moulded indoor grade polypropylene compound seat size : 52.5 cm. ( w ) x 53.2 cm. ( d ) back size : 51.6 cm. ( w ) x 40.5 cm. ( h ) 2 ) powder coated understructer:the powder coated ( dft 50±10 microns ) welded tubular frame should bemade from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm mserw tube. 3 ) shoe : the shoes should bemade of indoor grade polypropylene compound and snap fitted with tubular frame. 4 ) armrest : the armrest should bemade of indoor grade polypropylene compound and assembled over the tubular frame. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chair plastic ( 1 ) seat / back: the seat and back should bemade up of injection moulded indoor grade polypropylene compound seat size : 52.5 cm. ( w ) x 53.2 cm. ( d ) back size : 51.6 cm. ( w ) x 40.5 cm. ( h ) 2 ) powder coated understructer:the powder coated ( dft 50±10 microns ) welded tubular frame should bemade from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm mserw tube. 3 ) shoe : the shoes should bemade of indoor grade polypropylene compound and snap fitted with tubular frame. 4 ) armrest : the armrest should bemade of indoor grade polypropylene compound and assembled over the tubular frame. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:1650x750x750 ( trident middle main deskwith eru ( rhs ) size shall be1650 width x 700 depth x 743 height ( main desk ) 1000 widthx 450depthx 743 height ( eru ) .top shall be of 18 mm thickness made of plt board with 2 mm edge banding. wenge and savannah maple plt board shall be used. the understructure shall be in pre laminated panels made with plt boards . 2 drawerand 3 drawer storage units with different combinations to support tops made with 18 mm plt boards of different colours.modesty and back panels made with 18 mm plt boards. the pedestals / storages shall be fitted with necessary locks. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene.4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , file storage ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , desk size:3600 x 600 x 680 ( the worktop is made of 25mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. soft closing dual access flap provided for access to power supply and data cables. the understructure consists of mixture of 25mm and 18mm pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. anodised aluminium alloy 63400 wp profile is added at bottom edges for improving the aesthetics. the product has a knock down construction. a wire raiser made of 0.8mm crca ms is:513. it is epoxy polyester powder coated ( dft 40 60 microns ) for flow of wires and cables. a power box with 2 cutouts on either sides for standard 8 module anchor roma is provided. beside each cutout, an additional cutout with plate is provided for mounting audio visual cables ( eg. hdmi, vga a, etc ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( seat / back assembly: the seat should bemade up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded polyurethane foam. the back should bemade up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. the back ply and foam should bedesigned with contoured lumber support for comfortable seating posture. back size48cm. ( w ) x 76.0cm. ( h ) seat size51.0cm. ( w ) x 48.0cm. ( d ) 2. high resilience ( hr ) polyurethane foam: the hr polyurethane foam for seat and back should bemoulded with density = 45 + / 2 kg / m³ and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the armrest top should bemade of moulded polyurethane ( p.u ) and mounted on to a drop lift height adjustable type m.s. tubular armrest support chrome plated. the armrest height should beadjustable up to 6.5±0.5cm. in 5 steps & also has swivel adjustment of 22º±2° on both sides. 4.knee tilt synchro mechanism with seat depth adjustment mechanism: the mechanism should bedesigned with the following features: •360° revolving type. •single point control. •front pivot for tilt with feet resting on ground ensuring more comfort. •tilt tension adjustment. •4 position locking with anti shock feature. •seat back tilting ratio of 1:2 •seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positions 5.adjustable backrest: the backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 4 positions for correct position of lumber support. 6.pneumatic height adjustment: the pneumatic height adjustment has an adjustment of 9.0 ±0.3cm. 7.pedestal assembly:the pedestal should befabricated from 0.2 ± 0.02 cm thick hr sheet ( should be: dd 1079 / hrskin pass ) , chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twinwheel castors. the pedestal should be66.0±0.5cm. pitch center dia. ( 76.0±1.0 cm with castors ) . 8.twin wheel castors the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal should be a.back size 47.5 cm. ( w ) x58.0 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. 3.armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. tubular frame: the powder coated ( dft 40 60 microns ) tubular frame should becantilever type & made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. m.s. er.w. tube. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , projector trolley ( providing, supplying and placing of projector trolleyproduct size: vision projector trolley width: 545mm, depth: 838mm, height with castor: 1020mm. construction: rigid knock down construction. material: side panels, top / bottom panels, back panel, shelf panels, work surface panel, door andsupport frame panel are made from 18mm thick pre–laminated board of e1 p2 gradeand approved shade confirming to is 12823:1990 with 1.3mm pvc edge lipping.2 platforms are provided for projector and laptop usage. provision for the grommet is provided on the top panel, work surface panel andback panel for better wire management. lockable storage space with shelf is provided for storage of essential equipments. base plate assembly : dia 20mm ms rod bushes are fabricated by argo shield weldingon 8mm thk hr ( is 2062 ) plate and then powder coated. lockable castors are mounted onto the base plate assembly for ease of motion. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates:iaq gold ( by scs global ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:1650x750x750 ( trident middle main deskwith eru ( rhs ) size shall be1650 width x 700 depth x 743 height ( main desk ) 1000 widthx 450depthx 743 height ( eru ) .top shall be of 18 mm thickness made of plt board with 2 mm edge banding. wenge and savannah maple plt board shall be used. the understructure shall be in pre laminated panels made with plt boards . 2 drawerand 3 drawer storage units with different combinations to support tops made with 18 mm plt boards of different colours.modesty and back panels made with 18 mm plt boards. the pedestals / storages shall be fitted with necessary locks. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , file storage ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves, size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table with drawer, size: 2350x2350x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , almirah ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , conference table u shaped 14 str ( the worktop is made of 25mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. soft closing dual access flap provided for access to power supply and data cables. the understructure consists of mixture of 25mm and 18mm pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. anodised aluminium alloy 63400 wp profile is added at bottom edges for improving the aesthetics. the product has a knock down construction. a wire raiser made of 0.8mm crca ms is:513. it is epoxy polyester powder coated ( dft 40 60 microns ) for flow of wires and cables. a power box with 2 cutouts on either sides for standard 8 module anchor roma is provided. beside each cutout, an additional cutout with plate is provided for mounting audio visual cables ( eg. hdmi, vga a, etc ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal areaback size 47.5 cm. ( w ) x58.0 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , projector table ( providing, supplying and placing of projector trolleyproduct size: vision projector trolley width: 545mm, depth: 838mm, height with castor: 1020mm. construction: rigid knock down construction. material: side panels, top / bottom panels, back panel, shelf panels, work surface panel, door andsupport frame panel are made from 18mm thick pre–laminated board of e1 p2 gradeand approved shade confirming to is 12823:1990 with 1.3mm pvc edge lipping.2 platforms are provided for projector and laptop usage. provision for the grommet is provided on the top panel, work surface panel andback panel for better wire management. lockable storage space with shelf is provided for storage of essential equipments. base plate assembly : dia 20mm ms rod bushes are fabricated by argo shield weldingon 8mm thk hr ( is 2062 ) plate and then powder coated. lockable castors are mounted onto the base plate assembly for ease of motion. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates:iaq gold ( by scs global ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , conference table u shaped ( the worktop is made of 25mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. soft closing dual access flap provided for access to power supply and data cables. the understructure consists of mixture of 25mm and 18mm pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. anodised aluminium alloy 63400 wp profile is added at bottom edges for improving the aesthetics. the product has a knock down construction. a wire raiser made of 0.8mm crca ms is:513. it is epoxy polyester powder coated ( dft 40 60 microns ) for flow of wires and cables. a power box with 2 cutouts on either sides for standard 8 module anchor roma is provided. beside each cutout, an additional cutout with plate is provided for mounting audio visual cables ( eg. hdmi, vga a, etc ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , conference chair ( 1.seat assembly: the seat assembly should bemade up of 1.2 ±0.1cm. thick hot pressed plywood, upholstered with fabric upholstery covers and moulded polyurethane foam. seat size: 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.back assembly: the back asembly. should bemade of powder coated ( oft 40 60 microns ) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with contoured lumbar support for extra comfort. the back should beupholstered using double layer spacer mesh fabric with high tenacity yarn. back size : 46.5 cm ( w ) x 60.5 cm ( h ) 3.high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density =45+ / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 4.armrests: the one piece armrests should beinjection moulded from black co polymer polypropylene. 5.centre tilt mechanism: the mechashould be m should bedesigned with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • upright position locking. tilt tension adjustment.. 6.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. 7.telescopic bellow assy: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. 8.pedestal assembly: the pedestal should beinjection moulded in black 33% glass filled nylon66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors. ) 9. twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back chair ( seat / back assembly: the seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per qa method described in ocp qlta pl14 18 ; upholstered with synthetic leather over moulded high resilience polyurethane foam. * high back size:51.8 cm. ( w ) x 75.2 cm. ( h ) * seat size:49.0 cm. ( w ) x 51.4 cm. ( d ) high resilience ( hr ) polyurethane foam: the hr polyurethane foam is moulded with density =55+ / 2 kg / m³ and hardness 16 ± 2 kgf as per is:7888 for 25% compression. armrests: the adjustable armrest is designed with the following features : • up down adjustment– 8 steps ( 8.0±0.5cm range ) • height adjustable armrest structure which is chrome plated & fitted with an armrest top. front pivot synchro mechanism: the adjustable tilting mechanism is designedwith the following features. • 360° revolving type. • single point control. • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 4 position locking with anti shock feature. • seat / back tilting ratio of 1:2. back height adjustability: back can be adjusted in 5 positions by manually. stroke of height adjustable spine is 7 cm. back height adjustability is applicable for for high back and mid back chair. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. pedestal assembly with castors:the pedestal is high pressure die cast polished aluminium and fitted with 5 nos. twin wheel castors. the pedestal is 65.0 ± 0.5cm. pitch center dia. ( 75.0 ± 1.0cm. with castors. ) twin wheel castor: the twin wheel castors are injection moulded in black pp. option of sliding seat mechanism : seat can be slide horizontaly as per user convenience. stroke of seat slide is 5 cm. this option is available for revolving pedstal type of chair. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , projector trolley ( providing, supplying and placing of projector trolleyproduct size: vision projector trolley width: 545mm, depth: 838mm, height with castor: 1020mm. construction: rigid knock down construction. material: side panels, top / bottom panels, back panel, shelf panels, work surface panel, door andsupport frame panel are made from 18mm thick pre–laminated board of e1 p2 gradeand approved shade confirming to is 12823:1990 with 1.3mm pvc edge lipping.2 platforms are provided for projector and laptop usage. provision for the grommet is provided on the top panel, work surface panel andback panel for better wire management. lockable storage space with shelf is provided for storage of essential equipments. base plate assembly : dia 20mm ms rod bushes are fabricated by argo shield weldingon 8mm thk hr ( is 2062 ) plate and then powder coated. lockable castors are mounted onto the base plate assembly for ease of motion. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates:iaq gold ( by scs global ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) ....
Due Date : November 07, 2023
Tender Value : ₹ 59.15 Lakhs
