Health And Family Welfare Department - West Bengal

39408870 e tender for procurement of instruments through smis portal for non cat items ( ( 4th call ) , acrylizer for 16 flasks or more stainless steel lined both outside & inside. temperature is controlled by thermostat from 5°c above ambient to 100°c with a sensitivity of + 5’c with timer can be set 1 / 2 hour to 2 hours. drain valve is provided for dewaxing. to work on 220 / 240 volts ac. , curing pressure pot 5 liter or more capacity pressure pottemperature is preset to approximately 120°f and and manually adjusts to a maximum 160°f and. solid clad bottom provides even heat distribution. includes an easy to read, built in pressure gauge and quick release air valve.the pot has a safety device to prevent overheating, and a secure double locking lid. easy to clean stainless steel interior. rubber feet keep pot firmly in place. with lid gasket , deflasking unit operates on air pressure. with handheld chisel provided with detachable tips provided with variable power control with air inlet and tubing length not less than 1.5 meter. working pressure 1 6 bar , dental dewaxing unit with digital control for water temperature regulation. construction: stainless steel tank sizes ( 300 x 200 x 350 mm ) approximately water filling: manual heater: 2000 watts. with drain valve , duplicator a. programmable brushless agitator motor temperature controls for precision warmup and cool down phases optimised heating strategy and provision for effective disposal of gel and prevention of nozzle blockage maintenance of consistent gel quality voltage: 200230v, 50 / 60hz, b. pressure compaction unit for duplicating silicone materials automatic mixing and metering unit for two component silicone material , flask press flask press with base and cross bar made with high strength steel. the structural elements made with chromium plated steel. capable of pressing upto 1 to 3 flasks at a time. base should have holes for attachment to bench , high speed lathe ( rpm>6500 ) with suction unit electrically operated heavy duty motor unit having power not less than – 0.5hp high speed r.p.m.>6500 rpm arrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with built in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. table mountable heavy base plate for vibration free operation built – in lighting for high visibility , heavy duty lathe with suction unit electrically operated heavy duty motor unit having power not less than – 0.5hp high speed r.p.m. 3000 rpm arrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with built in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. table mountable heavy base plate for vibration free operation built – in lighting for high visibility , hydraulic press the closed circuit hydraulic press should work with a pressure up to 7000 kg of thrust. it can contain up to three flasks at a time. the structural elements in chromium plated steel. provided with dial. , implant retrieval kit implant retrieval & removal kit must contain implant remover compatible with all sizes, implant removal screw with easy identification and placement, screw drivers of different sizes and implant removal ratchet wrench ( indicates minimum & maximum torque ) kit must help in implant fixture fractured screw removal, abutment cover screw remover surgical tool. , mechanical press this equipment with base and cross bar made with high strength steel and the structural elements in chromium plated steel. capable of pressing upto 1 to 3 flasks at a time. base should have holes for attachment to bench , micro surveyor dental surveyor which is fully adjustable, ball type working base support 360 degree overall working interface, complete set with handpiece holder and precise angle. with all necessary surveyor tolls. , model trimmer with carborundum disc motor rpm 2800heavy duty , equipped with 2 ball bearing single speed rating continuous with buffer and 10 inch carborundum disc with heavy base that can be clamped and installed on underline table with water inlet and outflow water system , model trimmer with diamond disc ½ hp, motor rpm 2800, heavy duty, equipped with 2 ball bearing single speed rating continuous with buffer and 10 inch diamond disc rough, with heavy base with water inlet and outflow water system. , palatal trimmer provided with one fast cutting trimmer, electrically operated, rpm2600 or more, body made with304 grade stainless steel or non rusting alloy. dull finished works surface, dust collection with adapter hose. , • stereo microscope wide field eye pieces 10x / 20mm can accept 5x, 15x& 20x eye pieces, inter papillary distance adjustable 55 75mm, sufficient working distance, field of view 40mm at 5x and 20mm at 20xminimum 0.5x objective, erect image with magnification of 2.5x 100x, sufficient light source –led co axial reflected / top light 110v, proper zoom adjustment, dual power, optional auxiliary lens attachment, focus knob inclined lenses ( 45 degree ) . , spindle grinder with vacuum suction foot control and high intensity illumination. safety glass for glare elimination and visual protection. provision for connection dust collector suction. operating voltage 230vac + / 10% 50hz. motor rotation at 24000rpm or more with suction unit & dust collector. , • spot welder with soldering attachment • electrically operated • voltage110 240 volts • applications / indication spot welding • power settings2, 000 amperes • heat settings2 • electrode / tip type hand electrode • welding positions adjustable • includede components brass posts foot switch copper welding tips 2 remote electrode chords insulating material flux carbon points sample of solder prosthodontic work , vacuum mixing machine electrically operated motor 150 watts or more compact automatic regulation of the vacuum the mixing motor remains clean and is easily serviced due to a supporting filter and a fine filter in conjunction with the maintenance free vacuum pumpdirect connection between mixing bowl and vacuum pump – no disturbing exterior hosemechanical coupling to lock the mixing bowl in positionprovided with mixing bowls ( upto 500 g ) , • vibrator • electrically operated size 4.5 x 8 x 6.5 inches or more platform shape rectangular, type heavy duty • construction enamel painted body with rubber plate above body, speed: 3 speed vibration controller • platform shape rectangular , • wall hanging micromotor • dental hanging motoruniversal type, watt 330 400, rpm 10000 18000, rating 60 min. with extendable cord having all types bar attachment and foot control , knife sharpener automatic knife sharpener, equipped with automatic timer 0 60 min. to adjust sharpening time equipment should sharpen all microtome knives upto 140 mm in length. supplied with the following accessories in cabinet, universal knife holder 1 no.honing glass plate 2 nos. honing glass compound 1bottleknife inspection block 1 no.redressing pad 1 no. operating manual, micro abrasives suspension ma 2000 micro abrasive suspension for coarse honing of microtome knives ( 2 bottles of 200 ml. each ) ma 3000 micro abrasive suspension for fine honing of microtome knives ( 2 bottles of 200 ml. each ) . , distilled water plant voltage 220v, capacity 4 5l, driven type electric, semi automatic, stainless steel, single phase, material grade ss 304, type wall mounting , staining basket ( ss ) slide staining assembly of stainless steel with capacity to hold 12 slides , staining trough ( ss ) slide staining trough of stainless steel with capacity 25 slides having minimum dimension of 440*1100*190mm. , staining trough ( glass ) glass trough for staining 5 to 10 slides minimum, should be made of high grade soda glass. chemically stable& reasonably hard and extremely workable. , microtome ( manual ) dimensions ( w x d x h ) : 438 mm x 472 mm x 265 mm ( 17.24 x 18.58 x 10.43 in ) , section thickness setting range: 0.5 60 ?m total horizontal specimen feed: 25 mm, vertical specimen stroke59 mm specimen retraction: on / off approx. 20 ?m specimen orientation: xy ±8° trimming thickness: 10 ?m, 50 ?m , semi automatic microtome section thickness range from 0.5 to 100, vertical specimen stroke vertical 8 degree, z 360 degree, 220v, 50hz / 110v, 60hz, object feed 28mm, argonomic design, compact dimension, vertical guidance by zero backlash andcross roller bearings electronic precision feed mechanism with stepping motor technology. , spencers knife alloy steel, for use in laboratory, tip shape straight, blade width / thickness 1mm, head length 120mm, shape straight, handle plastic , pressure moulding machine ( dental ) thermally controlled heater reaches working temperature in few minutes. with inbuilt vacuum unit. power: 230 v, 850 to1000 w working pressure: 0, 5 – 6, 0 bar measurements ( w x h x l ) : 450 x 230 x 260 mm iso or ce certified , automatic digital electro polisher, auto / manual modes, with timers, electrolyte flow regulation 38 mm disc for psa paper & cloths supply 230 v. ac current – 2.5 amp., voltage – 80v, supply – 230 v.a.c.polishing probes – unique pen type system with recirculation of electrolyte, pump 25 watts reservoir ( 0.5 ltr ) , scanner with transparency adapter for dental use , dry heat sterilizer volume 25l, temp rt+10250 degree centigrade, fastheating with forced convection, adopt two sets of over temperature protection system, computer control, lcd display , anatomical articulator with face bow attached 1. rust free construction. 2. fixed condylar guidance with spring mounted elements that are attached to upper member3.incisal pin 4. mid incisal pin 5. orientation rod 6. incisal guide table 7. face bow attached , tracing table portable with opaque screen light box with led electrically operated with adjustable illumination. , induction casting machine with vacuum pump power:ac220v 50hz 60hz 2000watt or more centrifugal mount:600 r / min, melting type: induction, casting sequence 3 5 minutes , maximum melting temperature 1700 °c, maximum weight of alloy to be melted 60gms, built in vacuum pump with vacuum adjustment by digital software, vacuum level 0.7 bar or lesser, maximum pressure 3.5 bar attachment for argon gas supply. casting ring dimensions minimum 50 x 55mm & maximum 100 x 70mm motor power:350w or more , maximum temp 1200c working temp 1150c with digital display cum temperature controller with safety alarm size : 175x175x225mm 4.0k.w capacity , programmable porcelain furnace with vacuum pump power connection 50 60hz 200 240 v 50 60hz acceptable voltage fluctuations ±10% max. power consumption 8.5 a at 200 240v data for the vacuum pump: max. power consumption: 2.1 a final vacuum: < 50 mbar use only tested pumps display graphic lcd display with background lighting and touch screen display. dimensions of electrical fuses 110 120 v: diameter 6.3 x 32 mm 200 240 v: diameter 5 x 20 mm dimensions of the closed furnace depth: 430 mm width: 305 mm / 410 mm ( with cooling tray ) height: atleast 560 mm usable size of the firing chamber diameter: 80 mm height: 48 mm max. firing temperature 1200 °c / 2192 °f weight furnace base: 12.0 kg furnace head: 7.0 kg , sand blaster unit self illuminated chamber. unit with ventilation slits with rubber gloves, pressure regulator, air filter, provided with glass pane. flow of blasting material from 1 to 6 bar. with wear resistant nozzle tip attached with wear & tear resistant hoses & nozzles. with filter. micro & macro mode. , ceramic unit ceramic sculpturing & finishing kit comprising of high quality sable hair / synthetic filament brush size one zero, two zero and four zero and other sizes, ceramic curver, mosquito forcep, tweezer, ceramic pallete for mixing ceramic powder and other associated carving & finishing instruments , metal grinder high power motor, 1 / 3 horse power with 2850 rpm, adjustable transparent magnifier safety guard, low noise level, low power consumption. less weight , polishing lathe hi power motor, 1 / 3 horse power with 2850 rpm, single speedwith 3 chucks ( buffer , stone & bur chuck ) , metal cable arm and it’s attachment. , oscilating saw for dental use , autoclavefully programmable fully programmableautoclave with vacuum & dry cycle. capacity 22 24 litres chamber size and micro processor control, wrapped / unwrapped, porous, solid instrument including cotton swabs can be sterilised, digital display of pressure & temperature, silicon gasket, prevent any leakage of air, diagnostic automatic alarm for any malfunctioning, can be used at 121 degree c / 134 degree c during sterilisation, to storage times for fresh and used water, chamber size ( inner space ) 190x190x360 mm or more with built in water chamber provided with safety lock on door, gasket lined. provided with 3 trays. with digital display , trauma set including bone plating kit for dental use , implantologykit comprising of surgical armamentarium comprises of: point drill, pilot surgical drill, tap drill, drill extension, counter sink, stopper, connectors, parallel pin, depth gauge, torque ratchet, fixture direction pin, fixture driver, hex driver & other related items , implantologykitwith implantscomprising of surgical armamentarium comprises of: point drill, pilot surgical drill, tap drill, drill extension, counter sink, stopper, connectors, parallel pin, depth gauge, torque ratchet, fixture direction pin, fixture driver, hex driver & other related items dental implants , distraction osteogenesis kit for dental use , piezo surgical kit: device with intermittent operation, 60 sec on then 30 sec off with irrigation, & 30 sec on 120 sec off without irrigation, power supply 240v, 50 / 60 hz, maximum power absorbed 120va. surgical tip capable of modulating from 10, 30 & 60 cycles / s ( hz ) to 29khz. power adjustable from 2.8 to 16w. tip vibration in range of 60 200?m.motor with tips & other accessories , ultrasonic cleaner minimum capacity 13 liters with mesh bucket ultrasonic cleaner 220v, 100 200watt & above, 13 liter capacity, with stainless steel body &cover. , minor oral surgery kit for dental use , lab micromotor with hand piece compact and portable size, continuous variable speed control, r.p.m 1000 40000, on / off foot switch. one touch change of the driving direction for efficient operation with carbon brush motor with handpiece , high volume suction for dental use , automatic periapical x ray developer processes all films from 2 x 3 , 3 x 4, 15 x 30 up to 24 x 30 cms dry in 5 minutes, all auto processing of developing & fixing of x ray films auto temperature control and auto film transport standard packaging / physicalverification of sample may be made , radiovisiography& software with compatible desktop a ) x ray unit: dc x ray with timer & wall mounted scissor arm supported stand, tube voltage65 70 kvp tube current 4 8 ma radiation minimum exposure time 0.02 sec upto 3.2 sec, leakage radiation less than 0.25 mgs / hour maximum at a distance of 1 mt from focal point. compatible to rvg system. aerb approved. b ) digital intra oral sensor: 1.digital intra oral sensor with supporting software for computer to be provided 2.automatic controlled exposure technology sensor of size 1 rounded cornered, 1200 x 1600 pixel minimum, dimension 22 x 30 mm size 2 for all, having clipped corner, 1400 x 1920 pixels minimum, dimension 27 x 36 mm c ) desktop compatible with r.v.g , intra oral camera with 15 inch lcd monitor &software a ) : high resolution, easy to use, narrow head with led illumination, comfortable for patient .intra oral camera with provision of variable lens adjustment that can be attached to computer byusb b ) :provided with 15 inch lcd monitor c ) : software , technical specifications as follows or better saliography equipment & kit for dental use , opg & lateral cephalometry machine lateral tmj ( 2 or 4 views ) , maxillary sinus, segmented panoramic, digital system type, temporomandibular joint ( tmj ) , cone beam ct ( optional ) , cephalometric, segmented bitewing, panoramic, opg / tmj / ceph modes should be available, x ray generator : x ray expose time<=15 second, tube voltage 85 kilo watt, digital detector / panoramic modality, dicom compatible, computer to be supplied with the machine, detail of computer i3 cpu, 4 gb ram, 500gb hdd, 21” monitor, bit depth 14 bit or better, dental imaging software, windows 10 professional operating system, time to process & display image<10 second patient position standing sensor technology : cmos , lab micromotor heavy duty with hps compact and portable size, continuous variable speed control , r.p.m 1000 40000, on / off foot switch one touch change of the driving direction for efficient operation with handpiece. , steam cleaner dental steam cleaner: power 1500w or more, 220v, frequency 50 / 60hz. working pressure: 4 5 bar. capacity 5 10litre or more. with thermostat controller. device with both steam gun & button / lever controlled steaming attachment. stainless steel non rusting inner tank body. , air polisher air driven dental air polishing unit with reservoir hand held with connection to dental chair unit. sterilizable up to 275°f ( 135°c ) , 44 psi. iso or ce certified , composite finishing kit for use with contra angled latch type hand piece. for finishing composite restorations. specification to be quoted by the bidder / manufacturer . , physiodispenser implant motor with handpiece control unit with display panel, powerful motor with integrated thread cutting function, provided with tool control for hands free operation. speed controllable between r.p.m. of 200 40000. brushless micromotor, with upto 8 programmable memory. should have a attached saline stand & accessory irrigation tubings. hands free operation via foot control for speed / coolant solution flow volume / forward reverse / program. handpiece calibration system provided with cooling attachment system.handpiece 20:1 implant contra angle handpiece with pushbutton chuckautoclavable, can generate upto 80ncm torquepump output 70ml / minute , dental implants single stage and two stage dental implants with cover screw, impression analog, cover screw & other attachments , implant maintenance kit to prevent peri implantitis, 4pcs carbon fiber scalers+1pc periodontal probe & explore+1 pc autoclavable cassette , implant guide for multiple implant cases, the drill / parallel pin is kept inserted in the first drilling and that makes the adjacent drilling at 7mm and 9mm away from each other. most common distance between 2 implants placements. this tool maintains the angle of the drilling as well. the drilling will be exactly at the mesio distal distance required , sinus lifting instrument kit: for lateral & crestal approach with s reamer / lateral reamers initial drill / crestal drills bone inserter bone spreader bone carrier bone condenser depth gauge chisels of different width sinus curettes of various designs bone rongeur forceps steel mallet irrigation syringe & tips & other instruments autoclavable cassette 1 piece , osteotome size width: 3mm straight ( thickness at 10mm length: 1.50mm ) width: 4mm straight ( thickness at 10mm length: 1.75mm ) width: 5mm straight ( thickness at 10mm length: 2.00mm ) material handle non magnetic stainless steel 316l , implant removing kit long trephine drills used to remove bone around implants to remove the implant. 5.0 inner diameter: 4mm, outer diameter: 5mm 6.0 inner diameter: 5mm, outer diameter: 6mm , bone fixation screw for the expansion and condensing of the atrophic mandible and maxilla. sizes required expansion screw 2.6mm: 1.8mm ( apical ) to 2.6mm ( at 7mm length ) expansion screw 3.0mm: 2.1mm ( apical ) to 3.0mm ( at 7mm length ) expansion screw 3.4mm: 2.4mm ( apical ) to 3.4mm ( at 7mm length ) expansion screw 3.8mm: 2.7mm ( apical ) to 3.8mm ( at 7mm length ) expansion screw 4.3mm: 2.9mm ( apical ) to 4.3mm ( at 7mm length , bone scrapper it is used to remove the autologous bone for grafting procedure. the bone scraper has 5mm and 6mm wide working ends. made from surgical grade stainless steel for longevity and corrosion resistance. , bone trephine to harvest autologous cortical bone graft. kit of 8 drills having sizes : 3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm , electrocauterykit electrosurgical cautery which is comparatively a newer development functions by applying a high frequency alternating polarity of electrical current to cut, and fulgurate tissues. this process not only minimizes blood loss but also allows for more precise cuts. frequency 1.5 to 1.7 mhz output power 70 watt , typhodont articulator withmetal teeth and wax rim of class i, ii, iii articulated model with soft pink ( not transparent ) acrylic or plastic gingiva material. included:28 anatomically shaped screwabletypodontivorine teeth , articulated model with soft pink ( not transparent ) acrylic or plastic gingiva material. included:28 anatomically shaped screwabletypodontivorine teeth , endodontic hand pieces with micro tips and retro treatment kit comprising of a. ultrasonic piezoelectricscaler with inbuilt irrigation , led & water tank b. ultrasonicendodonticretro surgicaltips ( for anteriorteethupper & lower and posterior teeth of upper and lower arch ) c. ultrasonicpassive irrigation, d. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal , autoclave for hand piece sterilization the machine, characterized by small and elegant. high efficient and thorough sterilization, can be used for the sterilization of small high temperature resistant utensils and articles of medical users. • preset solution volume based on handpiece type ( high speed handpieces, lowspeedhandpieces ) • thorough cleaning and lubrication with simple operation • chuck cleaning function ensures that the chuck is thoroughly cleaned and lubricated • purging select mode ensures complete removal of excess oil integrated large oil tank ( 1.2 litre ) reduces burden of refill , conventional vlc unit led based. light modes fast, ramped & pulsed display for mode & timer selection chordless with rechargeable lithium battery light intensity not less than 1200 mw / cm2output peak wavelength range 450 490 nm ( intensity maximum at 460 nm ) with inbuilt timer, on off switch , endomotor with torque control hand piece. continuous & / or reciprocating motions for root canal shaping, hand piece with integrated on off switch, auto reverse mode, speed 250 1200 rpm. torque range 0.6 4 ncm, multiple adjustable programs standard packaging / physicalverification of sample may be , injectablegutta percha obturation kit containing: dual kit pluggers variable sizes. flexible extra long heat conductible silver alloy cannula, 1 cartridge capable of filling more than 3 root canals preferably with arrangement for back filling. , reconstruction surgical operating microscope with microscopic co observation systems: working distance & focusing 215 500mm continuously variable through motorized multifocal lens that can be controlled & focused through hand & foot control switch & manual adjustment override. magnification upto 18 x eyepieces: 12.5 x powerful led or xenon based illumination system controlled through hand & foot control switch & manual. with built in automatic zoom synchronized illumination field diameter, manual override & iris controller. binocular tube tiltableupto 180 degrees with variable diapter settings. suspension system with height, lateral movement adjustable floor stand, with position locking facility. microscope should have automatic circuit breaker, voltage 230v + 10%, frequency 50 60 hz. ce / fda approved. beam splitter: stereoscopic beam splitter have minimum of four port. have stereo co observervation attachment for assistant 360° movement of binocular with 12 x or more eyepiece with diapter setting from +5d to 8d. face to face attachment with 0 180° tiltable binocular tube with 12 x eyepiece with stereoscope having similar view with main surgeondiapter setting from +5d to 8d. full hd video camera display:hd display system attached with microscope body. ( no external monitor / detachable monitor will be acceptable ) . recording system with integrated hdd. recorder should have hdmi input & output. permit precise movement of camera & microscope in vertical & horizontal plane. ( european ce / fda ( usa ) approved ) , endodontic microsurgical equipment: comprising of a. ultrasonic piezoelectricscaler with inbuilt irrigation , led & water tank b. ultrasonicendodonticretro surgicaltips ( for anteriorteethupper & lower and posterior teeth of upper and lower arch ) c. ultrasonicpassive irrigation, d. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal , magnification loupes 4.5x ergonomically designed binocular loupe that can be worn over spectacle frame capable of 4.5xmagnification at 420mm with 3watt led rechargeable light , technical specifications as follows or better composite polishing kit finishing & polishing kit is designed for finishing and polishing of composite & gic restorations, consisting of dierent color coded stones. • 4 x white stone finishers fg 2 x green silicone polishers , ceramic finishing kit efficient kit designed for fine finishing and polishing of porcelain restorations eliminates the need for re glazing of the porcelain restoration, especially after chairside adjustment. recommended average speed: dura white stones: speed of 5, 000 – 20, 000 rpm ceramiste points: speed of 10, 000 – 12, 000 rpm dura white stones: speed of 5, 000 – 20, 000 rpm , metal finishing kit efficient kit designed for fine finishing and polishing of metal restorations , amalgam finishing kit efficient kit designed for fine finishing and polishing of metal restorations intra orally. , automatic developer used to view of the film processing design, can wash 30*40mm single film. package dimensions 13.9 x 13 x 11.2 inches ( 35.3 x 33 x 28.6 cm ) ; 5.2 pounds ( 2.34 kg ) technical: use for film size:30*40mm the biggest irrigation width:50mm medicine tank capacity: enhancement of 250ml, fixing 250ml, 250ml water washing method: manual developing temperature: room temperature material: environmentally friendly medical plastic net weight:2.5kg products size:395*325*230mm packing list: main machine : one set three potion 250ml cup , chairside microabrasion a portable pneumatic device, easy to install and operate, designated to surface blasting o prosthesis / restoration. work pressure 60 a 80 lbf / pol ( 4 5, 5 kgf / cm ) , bleachng unit led based tooth whitening system with intensity and timer controlling unit with portable multi arm attachment electrically operated , instrument retrieval kit this system is designed to assist in the removal of intra canal obstructions such as file segments, carrier based obturators and silver points. the rugged yet simplistic design makes obstruction removal less challenging. constructed from titanium and stainless steel and redesigned to insure maximum “bite”. features: 4 sizes for all areas of the canal ( ranging from .4mm to 1.3mm i.d. ) geometrically descending sizes to accommodate canal anatomy simplistic 2 piece design constructed using titanium and stainless steel cut out window “tilt back” lumen feature rapid taper titanium screw wedge color coded silicone grip reverse thread , amalgamator with automatic dispenser input voltage 220 230v provided with touch pad selector pre programmed time setting quiet, high speed mix capsules built in automatic timer capsule holder accepts all types of amalgam capsule , glass bead sterilizer electrically temperature regulated to heat contained glass beads with on off switch. small rectangular base for keeping at chairside provided with lid. it should reach operating temperature of approximately 240 c to 270 c in 15 20 minutes time. sterilization is on contact with glass beads .unit can be left in the “on” position all day and is safe for use in laminar flow cabinets. , vibrator • electrically operated size 4.5 x 8 x 6.5 inches or more platform shape rectangular, type heavy duty construction enamel painted body with rubber plate above body, speed: 3 speed vibration controller • platform shape rectangular , cad cam milling machine capable of unattended 5 axis milling with simple one button operation precision milling of wax, zirconia, nano composites and pmma blocks using fully automated 8 position disc changer unit integrated air flow system keeps work area clean sintering unit sintering unit capable of maintaining high temperature of around 1500 degree celsius for 5 hours or more with vacuum unit 110 240 volts 50 60hz with cad / cam unit capable of unattended 5 axis scanning diagnostic notification system alerts user of machine status cam software material sizes supported disc, pin & ingot ( european ce / fda approved ) &iso / dtr 18845 ( dentistry test methods for machining accuracy of computer aided milling machines ) , lab airrotor for precision carving of metal and ceramic , a. laser guided pin drilling system ( pindex system ) electrically operated 220v, laser guided pinsetter, pin drilling for easy die pin attachment. laser light technology with carbide bur drill with high speed motor. to accurately drill parallel holes into the underside of the model b. pins for use with laser guided pin drilling system ( pindex system ) system of various sizes made with non corrosive alloys for use with laser guided pin drilling system . in unit pack of 100 pieces , circular saw the motorised model slitting is the state of the art “precision slitting technique through models. the manual model slitting leads to various errors like inclined plane, non uniform gap and rough slit surface. the high speed slitting by circular saw eliminates all the shortcomings of manual slitting and improves the productivity. the model can be held firmly on the electromagnetic model holder. the illumination lamp gives clear vision of the working model. , vacuum investment unit voltage 85 245v 50 / 60 hz mixing speed 100 500 rpm premix, 100 400 rpm vacuum 27.5 in hg ( 930 mbar ) user programs 25 mixing time1 255 seconds ( 4.25 minutes ) capable of mixing unit amount of investment material under vacuum through a motor , pneumatic chisel • robust high performance chisel operated by compressed air for universal use in the laboratory. • high frequency chisel to deflask dentures and disinvest casting. • avoid, micro cracks formed by unconventional methods of plaster removal. • high quality compressed air control. • filter, lubricator, regulator, unit built in circu , facebow with semi adjustable articulator hanau wide view arcon articulator with spring bow, earpiece, face bow, orbital indicator, bite fork, mounting plates & other accessories , laser ( hard tissue ) hard tissue laser er, cr: ysgg laser, 0.1 9.0w ( 450 mj ) 10 50 hz, laser classification 4, voltage 100 230 vac , of wave length 2780nm erbium yag laser, pulse energy upto 700 mj, power upto 8.4 watt on tissue, frequency 10hz 50hz, wavelength 2940nm...

Health And Family Welfare Department - West Bengal

37864577 e tender for procurement of instruments through smis portal for non cat items ( 3rd call ) , acrylizer for 16 flasks or more stainless steel lined both outside & inside. temperature is controlled by thermostat from 5°c above ambient to 100°c with a sensitivity of + 5’c with timer can be set 1 / 2 hour to 2 hours. drain valve is provided for dewaxing. to work on 220 / 240 volts ac. , curing pressure pot 5 liter or more capacity pressure pottemperature is preset to approximately 120°f and and manually adjusts to a maximum 160°f and. solid clad bottom provides even heat distribution. includes an easy to read, built in pressure gauge and quick release air valve.the pot has a safety device to prevent overheating, and a secure double locking lid. easy to clean stainless steel interior. rubber feet keep pot firmly in place. with lid gasket , deflasking unit operates on air pressure. with handheld chisel provided with detachable tips provided with variable power control with air inlet and tubing length not less than 1.5 meter. working pressure 1 6 bar , dental dewaxing unit with digital control for water temperature regulation. construction: stainless steel tank sizes ( 300 x 200 x 350 mm ) approximately water filling: manual heater: 2000 watts. with drain valve , duplicator a. programmable brushless agitator motor temperature controls for precision warmup and cool down phases optimised heating strategy and provision for effective disposal of gel and prevention of nozzle blockage maintenance of consistent gel quality voltage: 200230v, 50 / 60hz, b. pressure compaction unit for duplicating silicone materials automatic mixing and metering unit for two component silicone material , flask press flask press with base and cross bar made with high strength steel. the structural elements made with chromium plated steel. capable of pressing upto 1 to 3 flasks at a time. base should have holes for attachment to bench , high speed lathe ( rpm>6500 ) with suction unit electrically operated heavy duty motor unit having power not less than – 0.5hp high speed r.p.m.>6500 rpm arrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with built in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. table mountable heavy base plate for vibration free operation built – in lighting for high visibility , heavy duty lathe with suction unit electrically operated heavy duty motor unit having power not less than – 0.5hp high speed r.p.m. 3000 rpm arrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with built in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. table mountable heavy base plate for vibration free operation built – in lighting for high visibility , hydraulic press the closed circuit hydraulic press should work with a pressure up to 7000 kg of thrust. it can contain up to three flasks at a time. the structural elements in chromium plated steel. provided with dial. , implant retrieval kit implant retrieval & removal kit must contain implant remover compatible with all sizes, implant removal screw with easy identification and placement, screw drivers of different sizes and implant removal ratchet wrench ( indicates minimum & maximum torque ) kit must help in implant fixture fractured screw removal, abutment cover screw remover surgical tool. , mechanical press this equipment with base and cross bar made with high strength steel and the structural elements in chromium plated steel. capable of pressing upto 1 to 3 flasks at a time. base should have holes for attachment to bench , micro surveyor dental surveyor which is fully adjustable, ball type working base support 360 degree overall working interface, complete set with handpiece holder and precise angle. with all necessary surveyor tolls. , model trimmer with carborundum disc motor rpm 2800heavy duty , equipped with 2 ball bearing single speed rating continuous with buffer and 10 inch carborundum disc with heavy base that can be clamped and installed on underline table with water inlet and outflow water system , model trimmer with diamond disc ½ hp, motor rpm 2800, heavy duty, equipped with 2 ball bearing single speed rating continuous with buffer and 10 inch diamond disc rough, with heavy base with water inlet and outflow water system. , palatal trimmer provided with one fast cutting trimmer, electrically operated, rpm2600 or more, body made with304 grade stainless steel or non rusting alloy. dull finished works surface, dust collection with adapter hose. , • stereo microscope wide field eye pieces 10x / 20mm can accept 5x, 15x& 20x eye pieces, inter papillary distance adjustable 55 75mm, sufficient working distance, field of view 40mm at 5x and 20mm at 20xminimum 0.5x objective, erect image with magnification of 2.5x 100x, sufficient light source –led co axial reflected / top light 110v, proper zoom adjustment, dual power, optional auxiliary lens attachment, focus knob inclined lenses ( 45 degree ) . , spindle grinder with vacuum suction foot control and high intensity illumination. safety glass for glare elimination and visual protection. provision for connection dust collector suction. operating voltage 230vac + / 10% 50hz. motor rotation at 24000rpm or more with suction unit & dust collector. , • spot welder with soldering attachment • electrically operated • voltage110 240 volts • applications / indication spot welding • power settings2, 000 amperes • heat settings2 • electrode / tip type hand electrode • welding positions adjustable • includede components brass posts foot switch copper welding tips 2 remote electrode chords insulating material flux carbon points sample of solder prosthodontic work , vacuum mixing machine electrically operated motor 150 watts or more compact automatic regulation of the vacuum the mixing motor remains clean and is easily serviced due to a supporting filter and a fine filter in conjunction with the maintenance free vacuum pumpdirect connection between mixing bowl and vacuum pump – no disturbing exterior hosemechanical coupling to lock the mixing bowl in positionprovided with mixing bowls ( upto 500 g ) , • vibrator • electrically operated size 4.5 x 8 x 6.5 inches or more platform shape rectangular, type heavy duty • construction enamel painted body with rubber plate above body, speed: 3 speed vibration controller • platform shape rectangular , • wall hanging micromotor • dental hanging motoruniversal type, watt 330 400, rpm 10000 18000, rating 60 min. with extendable cord having all types bar attachment and foot control , knife sharpener automatic knife sharpener, equipped with automatic timer 0 60 min. to adjust sharpening time equipment should sharpen all microtome knives upto 140 mm in length. supplied with the following accessories in cabinet, universal knife holder 1 no.honing glass plate 2 nos. honing glass compound 1bottleknife inspection block 1 no.redressing pad 1 no. operating manual, micro abrasives suspension ma 2000 micro abrasive suspension for coarse honing of microtome knives ( 2 bottles of 200 ml. each ) ma 3000 micro abrasive suspension for fine honing of microtome knives ( 2 bottles of 200 ml. each ) . , distilled water plant voltage 220v, capacity 4 5l, driven type electric, semi automatic, stainless steel, single phase, material grade ss 304, type wall mounting , staining basket ( ss ) slide staining assembly of stainless steel with capacity to hold 12 slides , staining trough ( ss ) slide staining trough of stainless steel with capacity 25 slides having minimum dimension of 440*1100*190mm. , staining trough ( glass ) glass trough for staining 5 to 10 slides minimum, should be made of high grade soda glass. chemically stable& reasonably hard and extremely workable. , microtome ( manual ) dimensions ( w x d x h ) : 438 mm x 472 mm x 265 mm ( 17.24 x 18.58 x 10.43 in ) , section thickness setting range: 0.5 60 ?m total horizontal specimen feed: 25 mm, vertical specimen stroke59 mm specimen retraction: on / off approx. 20 ?m specimen orientation: xy ±8° trimming thickness: 10 ?m, 50 ?m , semi automatic microtome section thickness range from 0.5 to 100, vertical specimen stroke vertical 8 degree, z 360 degree, 220v, 50hz / 110v, 60hz, object feed 28mm, argonomic design, compact dimension, vertical guidance by zero backlash andcross roller bearings electronic precision feed mechanism with stepping motor technology. , spencers knife alloy steel, for use in laboratory, tip shape straight, blade width / thickness 1mm, head length 120mm, shape straight, handle plastic , pressure moulding machine ( dental ) thermally controlled heater reaches working temperature in few minutes. with inbuilt vacuum unit. power: 230 v, 850 to1000 w working pressure: 0, 5 – 6, 0 bar measurements ( w x h x l ) : 450 x 230 x 260 mm iso or ce certified , automatic digital electro polisher, auto / manual modes, with timers, electrolyte flow regulation 38 mm disc for psa paper & cloths supply 230 v. ac current – 2.5 amp., voltage – 80v, supply – 230 v.a.c.polishing probes – unique pen type system with recirculation of electrolyte, pump 25 watts reservoir ( 0.5 ltr ) , scanner with transparency adapter for dental use , dry heat sterilizer volume 25l, temp rt+10250 degree centigrade, fastheating with forced convection, adopt two sets of over temperature protection system, computer control, lcd display , anatomical articulator with face bow attached 1. rust free construction. 2. fixed condylar guidance with spring mounted elements that are attached to upper member3.incisal pin 4. mid incisal pin 5. orientation rod 6. incisal guide table 7. face bow attached , tracing table portable with opaque screen light box with led electrically operated with adjustable illumination. , induction casting machine with vacuum pump power:ac220v 50hz 60hz 2000watt or more centrifugal mount:600 r / min, melting type: induction, casting sequence 3 5 minutes , maximum melting temperature 1700 °c, maximum weight of alloy to be melted 60gms, built in vacuum pump with vacuum adjustment by digital software, vacuum level 0.7 bar or lesser, maximum pressure 3.5 bar attachment for argon gas supply. casting ring dimensions minimum 50 x 55mm & maximum 100 x 70mm motor power:350w or more , maximum temp 1200c working temp 1150c with digital display cum temperature controller with safety alarm size : 175x175x225mm 4.0k.w capacity , programmable porcelain furnace with vacuum pump power connection 50 60hz 200 240 v 50 60hz acceptable voltage fluctuations ±10% max. power consumption 8.5 a at 200 240v data for the vacuum pump: max. power consumption: 2.1 a final vacuum: < 50 mbar use only tested pumps display graphic lcd display with background lighting and touch screen display. dimensions of electrical fuses 110 120 v: diameter 6.3 x 32 mm 200 240 v: diameter 5 x 20 mm dimensions of the closed furnace depth: 430 mm width: 305 mm / 410 mm ( with cooling tray ) height: atleast 560 mm usable size of the firing chamber diameter: 80 mm height: 48 mm max. firing temperature 1200 °c / 2192 °f weight furnace base: 12.0 kg furnace head: 7.0 kg , sand blaster unit self illuminated chamber. unit with ventilation slits with rubber gloves, pressure regulator, air filter, provided with glass pane. flow of blasting material from 1 to 6 bar. with wear resistant nozzle tip attached with wear & tear resistant hoses & nozzles. with filter. micro & macro mode. , ceramic unit ceramic sculpturing & finishing kit comprising of high quality sable hair / synthetic filament brush size one zero, two zero and four zero and other sizes, ceramic curver, mosquito forcep, tweezer, ceramic pallete for mixing ceramic powder and other associated carving & finishing instruments , metal grinder high power motor, 1 / 3 horse power with 2850 rpm, adjustable transparent magnifier safety guard, low noise level, low power consumption. less weight , polishing lathe hi power motor, 1 / 3 horse power with 2850 rpm, single speedwith 3 chucks ( buffer , stone & bur chuck ) , metal cable arm and it’s attachment. , oscilating saw for dental use , autoclavefully programmable fully programmableautoclave with vacuum & dry cycle. capacity 22 24 litres chamber size and micro processor control, wrapped / unwrapped, porous, solid instrument including cotton swabs can be sterilised, digital display of pressure & temperature, silicon gasket, prevent any leakage of air, diagnostic automatic alarm for any malfunctioning, can be used at 121 degree c / 134 degree c during sterilisation, to storage times for fresh and used water, chamber size ( inner space ) 190x190x360 mm or more with built in water chamber provided with safety lock on door, gasket lined. provided with 3 trays. with digital display , trauma set including bone plating kit for dental use , implantologykit comprising of surgical armamentarium comprises of: point drill, pilot surgical drill, tap drill, drill extension, counter sink, stopper, connectors, parallel pin, depth gauge, torque ratchet, fixture direction pin, fixture driver, hex driver & other related items , implantologykitwith implantscomprising of surgical armamentarium comprises of: point drill, pilot surgical drill, tap drill, drill extension, counter sink, stopper, connectors, parallel pin, depth gauge, torque ratchet, fixture direction pin, fixture driver, hex driver & other related items dental implants , distraction osteogenesis kit for dental use , piezo surgical kit: device with intermittent operation, 60 sec on then 30 sec off with irrigation, & 30 sec on 120 sec off without irrigation, power supply 240v, 50 / 60 hz, maximum power absorbed 120va. surgical tip capable of modulating from 10, 30 & 60 cycles / s ( hz ) to 29khz. power adjustable from 2.8 to 16w. tip vibration in range of 60 200?m.motor with tips & other accessories , ultrasonic cleaner minimum capacity 13 liters with mesh bucket ultrasonic cleaner 220v, 100 200watt & above, 13 liter capacity, with stainless steel body &cover. , minor oral surgery kit for dental use , lab micromotor with hand piece compact and portable size, continuous variable speed control, r.p.m 1000 40000, on / off foot switch. one touch change of the driving direction for efficient operation with carbon brush motor with handpiece , high volume suction for dental use , automatic periapical x ray developer processes all films from 2 x 3 , 3 x 4, 15 x 30 up to 24 x 30 cms dry in 5 minutes, all auto processing of developing & fixing of x ray films auto temperature control and auto film transport standard packaging / physicalverification of sample may be made , radiovisiography& software with compatible desktop a ) x ray unit: dc x ray with timer & wall mounted scissor arm supported stand, tube voltage65 70 kvp tube current 4 8 ma radiation minimum exposure time 0.02 sec upto 3.2 sec, leakage radiation less than 0.25 mgs / hour maximum at a distance of 1 mt from focal point. compatible to rvg system. aerb approved. b ) digital intra oral sensor: 1.digital intra oral sensor with supporting software for computer to be provided 2.automatic controlled exposure technology sensor of size 1 rounded cornered, 1200 x 1600 pixel minimum, dimension 22 x 30 mm size 2 for all, having clipped corner, 1400 x 1920 pixels minimum, dimension 27 x 36 mm c ) desktop compatible with r.v.g , intra oral camera with 15 inch lcd monitor &software a ) : high resolution, easy to use, narrow head with led illumination, comfortable for patient .intra oral camera with provision of variable lens adjustment that can be attached to computer byusb b ) :provided with 15 inch lcd monitor c ) : software , technical specifications as follows or better saliography equipment & kit for dental use , opg & lateral cephalometry machine lateral tmj ( 2 or 4 views ) , maxillary sinus, segmented panoramic, digital system type, temporomandibular joint ( tmj ) , cone beam ct ( optional ) , cephalometric, segmented bitewing, panoramic, opg / tmj / ceph modes should be available, x ray generator : x ray expose time<=15 second, tube voltage 85 kilo watt, digital detector / panoramic modality, dicom compatible, computer to be supplied with the machine, detail of computer i3 cpu, 4 gb ram, 500gb hdd, 21” monitor, bit depth 14 bit or better, dental imaging software, windows 10 professional operating system, time to process & display image<10 second patient position standing sensor technology : cmos , lab micromotor heavy duty with hps compact and portable size, continuous variable speed control , r.p.m 1000 40000, on / off foot switch one touch change of the driving direction for efficient operation with handpiece. , steam cleaner dental steam cleaner: power 1500w or more, 220v, frequency 50 / 60hz. working pressure: 4 5 bar. capacity 5 10litre or more. with thermostat controller. device with both steam gun & button / lever controlled steaming attachment. stainless steel non rusting inner tank body. , air polisher air driven dental air polishing unit with reservoir hand held with connection to dental chair unit. sterilizable up to 275°f ( 135°c ) , 44 psi. iso or ce certified , composite finishing kit for use with contra angled latch type hand piece. for finishing composite restorations. specification to be quoted by the bidder / manufacturer . , physiodispenser implant motor with handpiece control unit with display panel, powerful motor with integrated thread cutting function, provided with tool control for hands free operation. speed controllable between r.p.m. of 200 40000. brushless micromotor, with upto 8 programmable memory. should have a attached saline stand & accessory irrigation tubings. hands free operation via foot control for speed / coolant solution flow volume / forward reverse / program. handpiece calibration system provided with cooling attachment system.handpiece 20:1 implant contra angle handpiece with pushbutton chuckautoclavable, can generate upto 80ncm torquepump output 70ml / minute , dental implants single stage and two stage dental implants with cover screw, impression analog, cover screw & other attachments , implant maintenance kit to prevent peri implantitis, 4pcs carbon fiber scalers+1pc periodontal probe & explore+1 pc autoclavable cassette , implant guide for multiple implant cases, the drill / parallel pin is kept inserted in the first drilling and that makes the adjacent drilling at 7mm and 9mm away from each other. most common distance between 2 implants placements. this tool maintains the angle of the drilling as well. the drilling will be exactly at the mesio distal distance required , sinus lifting instrument kit: for lateral & crestal approach with s reamer / lateral reamers initial drill / crestal drills bone inserter bone spreader bone carrier bone condenser depth gauge chisels of different width sinus curettes of various designs bone rongeur forceps steel mallet irrigation syringe & tips & other instruments autoclavable cassette 1 piece , osteotome size width: 3mm straight ( thickness at 10mm length: 1.50mm ) width: 4mm straight ( thickness at 10mm length: 1.75mm ) width: 5mm straight ( thickness at 10mm length: 2.00mm ) material handle non magnetic stainless steel 316l , implant removing kit long trephine drills used to remove bone around implants to remove the implant. 5.0 inner diameter: 4mm, outer diameter: 5mm 6.0 inner diameter: 5mm, outer diameter: 6mm , bone fixation screw for the expansion and condensing of the atrophic mandible and maxilla. sizes required expansion screw 2.6mm: 1.8mm ( apical ) to 2.6mm ( at 7mm length ) expansion screw 3.0mm: 2.1mm ( apical ) to 3.0mm ( at 7mm length ) expansion screw 3.4mm: 2.4mm ( apical ) to 3.4mm ( at 7mm length ) expansion screw 3.8mm: 2.7mm ( apical ) to 3.8mm ( at 7mm length ) expansion screw 4.3mm: 2.9mm ( apical ) to 4.3mm ( at 7mm length , bone scrapper it is used to remove the autologous bone for grafting procedure. the bone scraper has 5mm and 6mm wide working ends. made from surgical grade stainless steel for longevity and corrosion resistance. , bone trephine to harvest autologous cortical bone graft. kit of 8 drills having sizes : 3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm , electrocauterykit electrosurgical cautery which is comparatively a newer development functions by applying a high frequency alternating polarity of electrical current to cut, and fulgurate tissues. this process not only minimizes blood loss but also allows for more precise cuts. frequency 1.5 to 1.7 mhz output power 70 watt , typhodont articulator withmetal teeth and wax rim of class i, ii, iii articulated model with soft pink ( not transparent ) acrylic or plastic gingiva material. included:28 anatomically shaped screwabletypodontivorine teeth , articulated model with soft pink ( not transparent ) acrylic or plastic gingiva material. included:28 anatomically shaped screwabletypodontivorine teeth , endodontic hand pieces with micro tips and retro treatment kit comprising of a. ultrasonic piezoelectricscaler with inbuilt irrigation , led & water tank b. ultrasonicendodonticretro surgicaltips ( for anteriorteethupper & lower and posterior teeth of upper and lower arch ) c. ultrasonicpassive irrigation, d. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal , autoclave for hand piece sterilization the machine, characterized by small and elegant. high efficient and thorough sterilization, can be used for the sterilization of small high temperature resistant utensils and articles of medical users. • preset solution volume based on handpiece type ( high speed handpieces, lowspeedhandpieces ) • thorough cleaning and lubrication with simple operation • chuck cleaning function ensures that the chuck is thoroughly cleaned and lubricated • purging select mode ensures complete removal of excess oil integrated large oil tank ( 1.2 litre ) reduces burden of refill , conventional vlc unit led based. light modes fast, ramped & pulsed display for mode & timer selection chordless with rechargeable lithium battery light intensity not less than 1200 mw / cm2output peak wavelength range 450 490 nm ( intensity maximum at 460 nm ) with inbuilt timer, on off switch , endomotor with torque control hand piece. continuous & / or reciprocating motions for root canal shaping, hand piece with integrated on off switch, auto reverse mode, speed 250 1200 rpm. torque range 0.6 4 ncm, multiple adjustable programs standard packaging / physicalverification of sample may be , injectablegutta percha obturation kit containing: dual kit pluggers variable sizes. flexible extra long heat conductible silver alloy cannula, 1 cartridge capable of filling more than 3 root canals preferably with arrangement for back filling. , reconstruction surgical operating microscope with microscopic co observation systems: working distance & focusing 215 500mm continuously variable through motorized multifocal lens that can be controlled & focused through hand & foot control switch & manual adjustment override. magnification upto 18 x eyepieces: 12.5 x powerful led or xenon based illumination system controlled through hand & foot control switch & manual. with built in automatic zoom synchronized illumination field diameter, manual override & iris controller. binocular tube tiltableupto 180 degrees with variable diapter settings. suspension system with height, lateral movement adjustable floor stand, with position locking facility. microscope should have automatic circuit breaker, voltage 230v + 10%, frequency 50 60 hz. ce / fda approved. beam splitter: stereoscopic beam splitter have minimum of four port. have stereo co observervation attachment for assistant 360° movement of binocular with 12 x or more eyepiece with diapter setting from +5d to 8d. face to face attachment with 0 180° tiltable binocular tube with 12 x eyepiece with stereoscope having similar view with main surgeondiapter setting from +5d to 8d. full hd video camera display:hd display system attached with microscope body. ( no external monitor / detachable monitor will be acceptable ) . recording system with integrated hdd. recorder should have hdmi input & output. permit precise movement of camera & microscope in vertical & horizontal plane. ( european ce / fda ( usa ) approved ) , endodontic microsurgical equipment: comprising of a. ultrasonic piezoelectricscaler with inbuilt irrigation , led & water tank b. ultrasonicendodonticretro surgicaltips ( for anteriorteethupper & lower and posterior teeth of upper and lower arch ) c. ultrasonicpassive irrigation, d. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal , magnification loupes 4.5x ergonomically designed binocular loupe that can be worn over spectacle frame capable of 4.5xmagnification at 420mm with 3watt led rechargeable light , technical specifications as follows or better composite polishing kit finishing & polishing kit is designed for finishing and polishing of composite & gic restorations, consisting of dierent color coded stones. • 4 x white stone finishers fg 2 x green silicone polishers , ceramic finishing kit efficient kit designed for fine finishing and polishing of porcelain restorations eliminates the need for re glazing of the porcelain restoration, especially after chairside adjustment. recommended average speed: dura white stones: speed of 5, 000 – 20, 000 rpm ceramiste points: speed of 10, 000 – 12, 000 rpm dura white stones: speed of 5, 000 – 20, 000 rpm , metal finishing kit efficient kit designed for fine finishing and polishing of metal restorations , amalgam finishing kit efficient kit designed for fine finishing and polishing of metal restorations intra orally. , automatic developer used to view of the film processing design, can wash 30*40mm single film. package dimensions 13.9 x 13 x 11.2 inches ( 35.3 x 33 x 28.6 cm ) ; 5.2 pounds ( 2.34 kg ) technical: use for film size:30*40mm the biggest irrigation width:50mm medicine tank capacity: enhancement of 250ml, fixing 250ml, 250ml water washing method: manual developing temperature: room temperature material: environmentally friendly medical plastic net weight:2.5kg products size:395*325*230mm packing list: main machine : one set three potion 250ml cup , chairside microabrasion a portable pneumatic device, easy to install and operate, designated to surface blasting o prosthesis / restoration. work pressure 60 a 80 lbf / pol ( 4 5, 5 kgf / cm ) , bleachng unit led based tooth whitening system with intensity and timer controlling unit with portable multi arm attachment electrically operated , instrument retrieval kit this system is designed to assist in the removal of intra canal obstructions such as file segments, carrier based obturators and silver points. the rugged yet simplistic design makes obstruction removal less challenging. constructed from titanium and stainless steel and redesigned to insure maximum “bite”. features: 4 sizes for all areas of the canal ( ranging from .4mm to 1.3mm i.d. ) geometrically descending sizes to accommodate canal anatomy simplistic 2 piece design constructed using titanium and stainless steel cut out window “tilt back” lumen feature rapid taper titanium screw wedge color coded silicone grip reverse thread , amalgamator with automatic dispenser input voltage 220 230v provided with touch pad selector pre programmed time setting quiet, high speed mix capsules built in automatic timer capsule holder accepts all types of amalgam capsule , glass bead sterilizer electrically temperature regulated to heat contained glass beads with on off switch. small rectangular base for keeping at chairside provided with lid. it should reach operating temperature of approximately 240 c to 270 c in 15 20 minutes time. sterilization is on contact with glass beads .unit can be left in the “on” position all day and is safe for use in laminar flow cabinets. , vibrator • electrically operated size 4.5 x 8 x 6.5 inches or more platform shape rectangular, type heavy duty construction enamel painted body with rubber plate above body, speed: 3 speed vibration controller • platform shape rectangular , cad cam milling machine capable of unattended 5 axis milling with simple one button operation precision milling of wax, zirconia, nano composites and pmma blocks using fully automated 8 position disc changer unit integrated air flow system keeps work area clean sintering unit sintering unit capable of maintaining high temperature of around 1500 degree celsius for 5 hours or more with vacuum unit 110 240 volts 50 60hz with cad / cam unit capable of unattended 5 axis scanning diagnostic notification system alerts user of machine status cam software material sizes supported disc, pin & ingot ( european ce / fda approved ) &iso / dtr 18845 ( dentistry test methods for machining accuracy of computer aided milling machines ) , lab airrotor for precision carving of metal and ceramic , a. laser guided pin drilling system ( pindex system ) electrically operated 220v, laser guided pinsetter, pin drilling for easy die pin attachment. laser light technology with carbide bur drill with high speed motor. to accurately drill parallel holes into the underside of the model b. pins for use with laser guided pin drilling system ( pindex system ) system of various sizes made with non corrosive alloys for use with laser guided pin drilling system . in unit pack of 100 pieces , circular saw the motorised model slitting is the state of the art “precision slitting technique through models. the manual model slitting leads to various errors like inclined plane, non uniform gap and rough slit surface. the high speed slitting by circular saw eliminates all the shortcomings of manual slitting and improves the productivity. the model can be held firmly on the electromagnetic model holder. the illumination lamp gives clear vision of the working model. , vacuum investment unit voltage 85 245v 50 / 60 hz mixing speed 100 500 rpm premix, 100 400 rpm vacuum 27.5 in hg ( 930 mbar ) user programs 25 mixing time1 255 seconds ( 4.25 minutes ) capable of mixing unit amount of investment material under vacuum through a motor , pneumatic chisel • robust high performance chisel operated by compressed air for universal use in the laboratory. • high frequency chisel to deflask dentures and disinvest casting. • avoid, micro cracks formed by unconventional methods of plaster removal. • high quality compressed air control. • filter, lubricator, regulator, unit built in circu , facebow with semi adjustable articulator hanau wide view arcon articulator with spring bow, earpiece, face bow, orbital indicator, bite fork, mounting plates & other accessories , laser ( hard tissue ) hard tissue laser er, cr: ysgg laser, 0.1 9.0w ( 450 mj ) 10 50 hz, laser classification 4, voltage 100 230 vac , of wave length 2780nm erbium yag laser, pulse energy upto 700 mj, power upto 8.4 watt on tissue, frequency 10hz 50hz, wavelength 2940nm...

Health And Family Welfare Department - West Bengal

36905405 wbhf/dch/955 e tender(2nd call) for procurement of instruments through smis portal for non cat items , acrylizer for 16 flasks or more stainless steel lined both outside & inside. temperature is controlled by thermostat from 5°c above ambient to 100°c with a sensitivity of + 5’c with timer can be set 1/2 hour to 2 hours. drain valve is provided for dewaxing. to work on 220/240 volts ac. , curing pressure pot 5 liter or more capacity pressure pottemperature is preset to approximately 120°f and and manually adjusts to a maximum 160°f and. solid clad bottom provides even heat distribution. includes an easy to read, built in pressure gauge and quick release air valve.the pot has a safety device to prevent overheating, and a secure double locking lid. easy to clean stainless steel interior. rubber feet keep pot firmly in place. with lid gasket , deflasking unit operates on air pressure. with handheld chisel provided with detachable tips provided with variable power control with air inlet and tubing length not less than 1.5 meter. working pressure 1 6 bar , dental dewaxing unit with digital control for water temperature regulation. construction: stainless steel tank sizes (300 x 200 x 350 mm) approximately water filling: manual heater: 2000 watts. with drain valve , duplicator a. programmable brushless agitator motor temperature controls for precision warmup and cool down phases optimised heating strategy and provision for effective disposal of gel and prevention of nozzle blockage maintenance of consistent gel quality voltage: 200230v, 50/60hz, b. pressure compaction unit for duplicating silicone materials automatic mixing and metering unit for two component silicone material , flask press flask press with base and cross bar made with high strength steel. the structural elements made with chromium plated steel. capable of pressing upto 1 to 3 flasks at a time. base should have holes for attachment to bench , high speed lathe (rpm>6500) with suction unit electrically operated heavy duty motor unit having power not less than – 0.5hp high speed r.p.m.>6500 rpm arrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with built in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. table mountable heavy base plate for vibration free operation built – in lighting for high visibility , heavy duty lathe with suction unit electrically operated heavy duty motor unit having power not less than – 0.5hp high speed r.p.m. 3000 rpm arrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with built in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. table mountable heavy base plate for vibration free operation built – in lighting for high visibility , hydraulic press the closed circuit hydraulic press should work with a pressure up to 7000 kg of thrust. it can contain up to three flasks at a time. the structural elements in chromium plated steel. provided with dial. , implant retrieval kit implant retrieval & removal kit must contain implant remover compatible with all sizes,implant removal screw with easy identification and placement,screw drivers of different sizes and implant removal ratchet wrench(indicates minimum & maximum torque) kit must help in implant fixture fractured screw removal, abutment cover screw remover surgical tool. , mechanical press this equipment with base and cross bar made with high strength steel and the structural elements in chromium plated steel. capable of pressing upto 1 to 3 flasks at a time. base should have holes for attachment to bench , micro surveyor dental surveyor which is fully adjustable, ball type working base support 360 degree overall working interface, complete set with handpiece holder and precise angle. with all necessary surveyor tolls. , model trimmer with carborundum disc motor rpm 2800heavy duty , equipped with 2 ball bearing single speed rating continuous with buffer and 10 inch carborundum disc with heavy base that can be clamped and installed on underline table with water inlet and outflow water system , model trimmer with diamond disc ½ hp, motor rpm 2800, heavy duty, equipped with 2 ball bearing single speed rating continuous with buffer and 10 inch diamond disc rough, with heavy base with water inlet and outflow water system. , palatal trimmer provided with one fast cutting trimmer, electrically operated, rpm2600 or more, body made with304 grade stainless steel or non rusting alloy. dull finished works surface, dust collection with adapter hose. , • stereo microscope wide field eye pieces 10x/20mm can accept 5x,15x& 20x eye pieces,inter papillary distance adjustable 55 75mm,sufficient working distance, field of view 40mm at 5x and 20mm at 20xminimum 0.5x objective, erect image with magnification of 2.5x 100x, sufficient light source –led co axial reflected/ top light 110v,proper zoom adjustment, dual power, optional auxiliary lens attachment, focus knob inclined lenses(45 degree). , spindle grinder with vacuum suction foot control and high intensity illumination. safety glass for glare elimination and visual protection. provision for connection dust collector suction. operating voltage 230vac +/ 10% 50hz. motor rotation at 24000rpm or more with suction unit & dust collector. , • spot welder with soldering attachment • electrically operated • voltage110 240 volts • applications / indication spot welding • power settings2,000 amperes • heat settings2 • electrode / tip type hand electrode • welding positions adjustable • includede components brass posts foot switch copper welding tips 2 remote electrode chords insulating material flux carbon points sample of solder prosthodontic work , vacuum mixing machine electrically operated motor 150 watts or more compact automatic regulation of the vacuum the mixing motor remains clean and is easily serviced due to a supporting filter and a fine filter in conjunction with the maintenance free vacuum pumpdirect connection between mixing bowl and vacuum pump – no disturbing exterior hosemechanical coupling to lock the mixing bowl in positionprovided with mixing bowls (upto 500 g ) , • vibrator • electrically operated size 4.5 x 8 x 6.5 inches or more platform shape rectangular, type heavy duty • construction enamel painted body with rubber plate above body, speed: 3 speed vibration controller • platform shape rectangular , • wall hanging micromotor • dental hanging motoruniversal type, watt 330 400, rpm 10000 18000, rating 60 min. with extendable cord having all types bar attachment and foot control , knife sharpener automatic knife sharpener, equipped with automatic timer 0 60 min. to adjust sharpening time equipment should sharpen all microtome knives upto 140 mm in length. supplied with the following accessories in cabinet, universal knife holder 1 no.honing glass plate 2 nos. honing glass compound 1bottleknife inspection block 1 no.redressing pad 1 no. operating manual,micro abrasives suspension ma 2000 micro abrasive suspension for coarse honing of microtome knives (2 bottles of 200 ml. each) ma 3000 micro abrasive suspension for fine honing of microtome knives (2 bottles of 200 ml. each). , distilled water plant voltage 220v,capacity 4 5l,driven type electric,semi automatic,stainless steel,single phase,material grade ss 304,type wall mounting , staining basket(ss) slide staining assembly of stainless steel with capacity to hold 12 slides , staining trough(ss) slide staining trough of stainless steel with capacity 25 slides having minimum dimension of 440*1100*190mm. , staining trough(glass) glass trough for staining 5 to 10 slides minimum, should be made of high grade soda glass. chemically stable& reasonably hard and extremely workable. , microtome(manual) dimensions (w x d x h): 438 mm x 472 mm x 265 mm (17.24 x 18.58 x 10.43 in), section thickness setting range: 0.5 60 ?m total horizontal specimen feed: 25 mm, vertical specimen stroke59 mm specimen retraction: on/off approx. 20 ?m specimen orientation: xy ±8° trimming thickness: 10 ?m, 50 ?m , semi automatic microtome section thickness range from 0.5 to 100,vertical specimen stroke vertical 8 degree,z 360 degree,220v,50hz/110v,60hz,object feed 28mm,argonomic design, compact dimension, vertical guidance by zero backlash andcross roller bearings electronic precision feed mechanism with stepping motor technology. , spencers knife alloy steel,for use in laboratory, tip shape straight,blade width /thickness 1mm, head length 120mm,shape straight, handle plastic , pressure moulding machine (dental) thermally controlled heater reaches working temperature in few minutes. with inbuilt vacuum unit. power: 230 v, 850 to1000 w working pressure: 0,5 – 6,0 bar measurements (w x h x l): 450 x 230 x 260 mm iso or ce certified , automatic digital electro polisher, auto/manual modes, with timers, electrolyte flow regulation 38 mm disc for psa paper & cloths supply 230 v. ac current – 2.5 amp., voltage – 80v, supply – 230 v.a.c.polishing probes – unique pen type system with recirculation of electrolyte, pump 25 watts reservoir (0.5 ltr) , scanner with transparency adapter for dental use , dry heat sterilizer volume 25l, temp rt+10250 degree centigrade, fastheating with forced convection, adopt two sets of over temperature protection system, computer control, lcd display , anatomical articulator with face bow attached 1. rust free construction. 2. fixed condylar guidance with spring mounted elements that are attached to upper member3.incisal pin 4. mid incisal pin 5. orientation rod 6. incisal guide table 7. face bow attached , tracing table portable with opaque screen light box with led electrically operated with adjustable illumination. , induction casting machine with vacuum pump power:ac220v 50hz 60hz 2000watt or more centrifugal mount:600 r/min, melting type: induction, casting sequence 3 5 minutes ,maximum melting temperature 1700 °c, maximum weight of alloy to be melted 60gms, built in vacuum pump with vacuum adjustment by digital software, vacuum level 0.7 bar or lesser, maximum pressure 3.5 bar attachment for argon gas supply. casting ring dimensions minimum 50 x 55mm & maximum 100 x 70mm motor power:350w or more , maximum temp 1200c working temp 1150c with digital display cum temperature controller with safety alarm size : 175x175x225mm 4.0k.w capacity , programmable porcelain furnace with vacuum pump power connection 50 60hz 200 240 v 50 60hz acceptable voltage fluctuations ±10% max. power consumption 8.5 a at 200 240v data for the vacuum pump: max. power consumption: 2.1 a final vacuum: < 50 mbar use only tested pumps display graphic lcd display with background lighting and touch screen display. dimensions of electrical fuses 110 120 v: diameter 6.3 x 32 mm 200 240 v: diameter 5 x 20 mm dimensions of the closed furnace depth: 430 mm width: 305 mm/410 mm (with cooling tray) height: atleast 560 mm usable size of the firing chamber diameter: 80 mm height: 48 mm max. firing temperature 1200 °c/2192 °f weight furnace base: 12.0 kg furnace head: 7.0 kg , sand blaster unit self illuminated chamber. unit with ventilation slits with rubber gloves, pressure regulator, air filter, provided with glass pane. flow of blasting material from 1 to 6 bar. with wear resistant nozzle tip attached with wear & tear resistant hoses & nozzles. with filter. micro & macro mode. , ceramic unit ceramic sculpturing & finishing kit comprising of high quality sable hair/ synthetic filament brush size one zero, two zero and four zero and other sizes, ceramic curver, mosquito forcep,tweezer, ceramic pallete for mixing ceramic powder and other associated carving & finishing instruments , metal grinder high power motor, 1/3 horse power with 2850 rpm, adjustable transparent magnifier safety guard, low noise level, low power consumption. less weight , polishing lathe hi power motor, 1/3 horse power with 2850 rpm,single speedwith 3 chucks(buffer ,stone & bur chuck),metal cable arm and it’s attachment. , oscilating saw for dental use , autoclavefully programmable fully programmableautoclave with vacuum & dry cycle. capacity 22 24 litres chamber size and micro processor control,wrapped/unwrapped,porous,solid instrument including cotton swabs can be sterilised, digital display of pressure & temperature, silicon gasket, prevent any leakage of air,diagnostic automatic alarm for any malfunctioning,can be used at 121 degree c/134 degree c during sterilisation, to storage times for fresh and used water,chamber size(inner space) 190x190x360 mm or more with built in water chamber provided with safety lock on door, gasket lined. provided with 3 trays. with digital display , trauma set including bone plating kit for dental use , implantologykit comprising of surgical armamentarium comprises of: point drill, pilot surgical drill, tap drill, drill extension, counter sink, stopper, connectors, parallel pin, depth gauge, torque ratchet, fixture direction pin, fixture driver, hex driver & other related items , implantologykitwith implantscomprising of surgical armamentarium comprises of: point drill, pilot surgical drill, tap drill, drill extension, counter sink, stopper, connectors, parallel pin, depth gauge, torque ratchet, fixture direction pin, fixture driver, hex driver & other related items dental implants , distraction osteogenesis kit for dental use , piezo surgical kit: device with intermittent operation, 60 sec on then 30 sec off with irrigation, & 30 sec on 120 sec off without irrigation, power supply 240v,50/60 hz, maximum power absorbed 120va. surgical tip capable of modulating from 10, 30 & 60 cycles/s (hz) to 29khz. power adjustable from 2.8 to 16w. tip vibration in range of 60 200?m.motor with tips & other accessories , ultrasonic cleaner minimum capacity 13 liters with mesh bucket ultrasonic cleaner 220v, 100 200watt & above, 13 liter capacity, with stainless steel body &cover. , minor oral surgery kit for dental use , lab micromotor with hand piece compact and portable size, continuous variable speed control, r.p.m 1000 40000, on/off foot switch. one touch change of the driving direction for efficient operation with carbon brush motor with handpiece , high volume suction for dental use , automatic periapical x ray developer processes all films from 2 x 3 , 3 x 4, 15 x 30 up to 24 x 30 cms dry in 5 minutes, all auto processing of developing & fixing of x ray films auto temperature control and auto film transport standard packaging/physicalverification of sample may be made , radiovisiography& software with compatible desktop a) x ray unit: dc x ray with timer & wall mounted scissor arm supported stand, tube voltage65 70 kvp tube current 4 8 ma radiation minimum exposure time 0.02 sec upto 3.2 sec, leakage radiation less than 0.25 mgs/hour maximum at a distance of 1 mt from focal point. compatible to rvg system. aerb approved. b) digital intra oral sensor: 1.digital intra oral sensor with supporting software for computer to be provided 2.automatic controlled exposure technology sensor of size 1 rounded cornered, 1200 x 1600 pixel minimum, dimension 22 x 30 mm size 2 for all, having clipped corner, 1400 x 1920 pixels minimum, dimension 27 x 36 mm c)desktop compatible with r.v.g , intra oral camera with 15 inch lcd monitor &software a): high resolution, easy to use, narrow head with led illumination, comfortable for patient .intra oral camera with provision of variable lens adjustment that can be attached to computer byusb b):provided with 15 inch lcd monitor c): software , technical specifications as follows or better saliography equipment & kit for dental use , opg & lateral cephalometry machine lateral tmj (2 or 4 views) , maxillary sinus, segmented panoramic, digital system type, temporomandibular joint(tmj),cone beam ct(optional), cephalometric,segmented bitewing,panoramic, opg/tmj/ceph modes should be available, x ray generator : x ray expose time<=15 second, tube voltage 85 kilo watt, digital detector/panoramic modality, dicom compatible, computer to be supplied with the machine, detail of computer i3 cpu,4 gb ram,500gb hdd,21” monitor, bit depth 14 bit or better, dental imaging software, windows 10 professional operating system, time to process & display image<10 second patient position standing sensor technology : cmos , lab micromotor heavy duty with hps compact and portable size, continuous variable speed control , r.p.m 1000 40000,on/off foot switch one touch change of the driving direction for efficient operation with handpiece. , steam cleaner dental steam cleaner: power 1500w or more, 220v, frequency 50/60hz. working pressure: 4 5 bar. capacity 5 10litre or more. with thermostat controller. device with both steam gun & button/lever controlled steaming attachment. stainless steel non rusting inner tank body. , air polisher air driven dental air polishing unit with reservoir hand held with connection to dental chair unit. sterilizable up to 275°f (135°c), 44 psi. iso or ce certified , composite finishing kit for use with contra angled latch type hand piece. for finishing composite restorations. specification to be quoted by the bidder/manufacturer . , physiodispenser implant motor with handpiece control unit with display panel, powerful motor with integrated thread cutting function, provided with tool control for hands free operation. speed controllable between r.p.m. of 200 40000. brushless micromotor, with upto 8 programmable memory. should have a attached saline stand & accessory irrigation tubings. hands free operation via foot control for speed/coolant solution flow volume/forward reverse/program. handpiece calibration system provided with cooling attachment system.handpiece 20:1 implant contra angle handpiece with pushbutton chuckautoclavable, can generate upto 80ncm torquepump output 70ml/minute , dental implants single stage and two stage dental implants with cover screw, impression analog,cover screw & other attachments , implant maintenance kit to prevent peri implantitis,4pcs carbon fiber scalers+1pc periodontal probe & explore+1 pc autoclavable cassette , implant guide for multiple implant cases, the drill/parallel pin is kept inserted in the first drilling and that makes the adjacent drilling at 7mm and 9mm away from each other. most common distance between 2 implants placements. this tool maintains the angle of the drilling as well. the drilling will be exactly at the mesio distal distance required , sinus lifting instrument kit: for lateral & crestal approach with s reamer/lateral reamers initial drill/crestal drills bone inserter bone spreader bone carrier bone condenser depth gauge chisels of different width sinus curettes of various designs bone rongeur forceps steel mallet irrigation syringe & tips & other instruments autoclavable cassette 1 piece , osteotome size width: 3mm straight (thickness at 10mm length: 1.50mm) width: 4mm straight (thickness at 10mm length: 1.75mm) width: 5mm straight (thickness at 10mm length: 2.00mm) material handle non magnetic stainless steel 316l , implant removing kit long trephine drills used to remove bone around implants to remove the implant. 5.0 inner diameter: 4mm, outer diameter: 5mm 6.0 inner diameter: 5mm, outer diameter: 6mm , bone fixation screw for the expansion and condensing of the atrophic mandible and maxilla. sizes required expansion screw 2.6mm: 1.8mm (apical) to 2.6mm (at 7mm length) expansion screw 3.0mm: 2.1mm (apical) to 3.0mm (at 7mm length) expansion screw 3.4mm: 2.4mm (apical) to 3.4mm (at 7mm length) expansion screw 3.8mm: 2.7mm (apical) to 3.8mm (at 7mm length) expansion screw 4.3mm: 2.9mm (apical) to 4.3mm (at 7mm length , bone scrapper it is used to remove the autologous bone for grafting procedure. the bone scraper has 5mm and 6mm wide working ends. made from surgical grade stainless steel for longevity and corrosion resistance. , bone trephine to harvest autologous cortical bone graft. kit of 8 drills having sizes : 3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm , electrocauterykit electrosurgical cautery which is comparatively a newer development functions by applying a high frequency alternating polarity of electrical current to cut, and fulgurate tissues. this process not only minimizes blood loss but also allows for more precise cuts. frequency 1.5 to 1.7 mhz output power 70 watt , typhodont articulator withmetal teeth and wax rim of class i,ii,iii articulated model with soft pink (not transparent) acrylic or plastic gingiva material. included:28 anatomically shaped screwabletypodontivorine teeth , articulated model with soft pink (not transparent) acrylic or plastic gingiva material. included:28 anatomically shaped screwabletypodontivorine teeth , endodontic hand pieces with micro tips and retro treatment kit comprising of a. ultrasonic piezoelectricscaler with inbuilt irrigation , led & water tank b. ultrasonicendodonticretro surgicaltips (for anteriorteethupper & lower and posterior teeth of upper and lower arch) c. ultrasonicpassive irrigation, d. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal , autoclave for hand piece sterilization the machine, characterized by small and elegant. high efficient and thorough sterilization, can be used for the sterilization of small high temperature resistant utensils and articles of medical users. • preset solution volume based on handpiece type (high speed handpieces, lowspeedhandpieces) • thorough cleaning and lubrication with simple operation • chuck cleaning function ensures that the chuck is thoroughly cleaned and lubricated • purging select mode ensures complete removal of excess oil integrated large oil tank (1.2 litre) reduces burden of refill , conventional vlc unit led based. light modes fast, ramped & pulsed display for mode & timer selection chordless with rechargeable lithium battery light intensity not less than 1200 mw/cm2output peak wavelength range 450 490 nm (intensity maximum at 460 nm) with inbuilt timer, on off switch , endomotor with torque control hand piece. continuous &/or reciprocating motions for root canal shaping, hand piece with integrated on off switch, auto reverse mode, speed 250 1200 rpm. torque range 0.6 4 ncm, multiple adjustable programs standard packaging/physicalverification of sample may be , injectablegutta percha obturation kit containing: dual kit pluggers variable sizes. flexible extra long heat conductible silver alloy cannula, 1 cartridge capable of filling more than 3 root canals preferably with arrangement for back filling. , reconstruction surgical operating microscope with microscopic co observation systems: working distance & focusing 215 500mm continuously variable through motorized multifocal lens that can be controlled & focused through hand & foot control switch & manual adjustment override. magnification upto 18 x eyepieces: 12.5 x powerful led or xenon based illumination system controlled through hand & foot control switch & manual. with built in automatic zoom synchronized illumination field diameter, manual override & iris controller. binocular tube tiltableupto 180 degrees with variable diapter settings. suspension system with height, lateral movement adjustable floor stand, with position locking facility. microscope should have automatic circuit breaker, voltage 230v + 10%, frequency 50 60 hz. ce/fda approved. beam splitter: stereoscopic beam splitter have minimum of four port. have stereo co observervation attachment for assistant 360° movement of binocular with 12 x or more eyepiece with diapter setting from +5d to 8d. face to face attachment with 0 180° tiltable binocular tube with 12 x eyepiece with stereoscope having similar view with main surgeondiapter setting from +5d to 8d. full hd video camera display:hd display system attached with microscope body. ( no external monitor/detachable monitor will be acceptable). recording system with integrated hdd. recorder should have hdmi input & output. permit precise movement of camera & microscope in vertical & horizontal plane. (european ce/ fda (usa)approved) , endodontic microsurgical equipment: comprising of a. ultrasonic piezoelectricscaler with inbuilt irrigation , led & water tank b. ultrasonicendodonticretro surgicaltips (for anteriorteethupper & lower and posterior teeth of upper and lower arch) c. ultrasonicpassive irrigation, d. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal , magnification loupes 4.5x ergonomically designed binocular loupe that can be worn over spectacle frame capable of 4.5xmagnification at 420mm with 3watt led rechargeable light , technical specifications as follows or better composite polishing kit finishing & polishing kit is designed for finishing and polishing of composite & gic restorations, consisting of dierent color coded stones. • 4 x white stone finishers fg 2 x green silicone polishers , ceramic finishing kit efficient kit designed for fine finishing and polishing of porcelain restorations eliminates the need for re glazing of the porcelain restoration, especially after chairside adjustment. recommended average speed: dura white stones: speed of 5, 000 – 20,000 rpm ceramiste points: speed of 10,000 – 12,000 rpm dura white stones: speed of 5,000 – 20,000 rpm , metal finishing kit efficient kit designed for fine finishing and polishing of metal restorations , amalgam finishing kit efficient kit designed for fine finishing and polishing of metal restorations intra orally. , automatic developer used to view of the film processing design, can wash 30*40mm single film. package dimensions 13.9 x 13 x 11.2 inches (35.3 x 33 x 28.6 cm); 5.2 pounds (2.34 kg) technical: use for film size:30*40mm the biggest irrigation width:50mm medicine tank capacity: enhancement of 250ml,fixing 250ml,250ml water washing method: manual developing temperature: room temperature material: environmentally friendly medical plastic net weight:2.5kg products size:395*325*230mm packing list: main machine : one set three potion 250ml cup , chairside microabrasion a portable pneumatic device, easy to install and operate, designated to surface blasting o prosthesis/ restoration. work pressure 60 a 80 lbf/pol (4 5,5 kgf/cm) , bleachng unit led based tooth whitening system with intensity and timer controlling unit with portable multi arm attachment electrically operated , instrument retrieval kit this system is designed to assist in the removal of intra canal obstructions such as file segments, carrier based obturators and silver points. the rugged yet simplistic design makes obstruction removal less challenging. constructed from titanium and stainless steel and redesigned to insure maximum “bite”. features: 4 sizes for all areas of the canal (ranging from .4mm to 1.3mm i.d.) geometrically descending sizes to accommodate canal anatomy simplistic 2 piece design constructed using titanium and stainless steel cut out window “tilt back” lumen feature rapid taper titanium screw wedge color coded silicone grip reverse thread , amalgamator with automatic dispenser input voltage 220 230v provided with touch pad selector pre programmed time setting quiet, high speed mix capsules built in automatic timer capsule holder accepts all types of amalgam capsule , glass bead sterilizer electrically temperature regulated to heat contained glass beads with on off switch. small rectangular base for keeping at chairside provided with lid. it should reach operating temperature of approximately 240 c to 270 c in 15 20 minutes time. sterilization is on contact with glass beads .unit can be left in the “on” position all day and is safe for use in laminar flow cabinets. , vibrator • electrically operated size 4.5 x 8 x 6.5 inches or more platform shape rectangular, type heavy duty construction enamel painted body with rubber plate above body, speed: 3 speed vibration controller • platform shape rectangular , cad cam milling machine capable of unattended 5 axis milling with simple one button operation precision milling of wax, zirconia, nano composites and pmma blocks using fully automated 8 position disc changer unit integrated air flow system keeps work area clean sintering unit sintering unit capable of maintaining high temperature of around 1500 degree celsius for 5 hours or more with vacuum unit 110 240 volts 50 60hz with cad/cam unit capable of unattended 5 axis scanning diagnostic notification system alerts user of machine status cam software material sizes supported disc, pin & ingot (european ce/fda approved) &iso/dtr 18845 (dentistry test methods for machining accuracy of computer aided milling machines) , lab airrotor for precision carving of metal and ceramic , a. laser guided pin drilling system (pindex system) electrically operated 220v, laser guided pinsetter, pin drilling for easy die pin attachment. laser light technology with carbide bur drill with high speed motor. to accurately drill parallel holes into the underside of the model b. pins for use with laser guided pin drilling system (pindex system) system of various sizes made with non corrosive alloys for use with laser guided pin drilling system . in unit pack of 100 pieces , circular saw the motorised model slitting is the state of the art “precision slitting technique through models. the manual model slitting leads to various errors like inclined plane, non uniform gap and rough slit surface. the high speed slitting by circular saw eliminates all the shortcomings of manual slitting and improves the productivity. the model can be held firmly on the electromagnetic model holder. the illumination lamp gives clear vision of the working model. , vacuum investment unit voltage 85 245v 50/60 hz mixing speed 100 500 rpm premix, 100 400 rpm vacuum 27.5 in hg (930 mbar )user programs 25 mixing time1 255 seconds (4.25 minutes ) capable of mixing unit amount of investment material under vacuum through a motor , pneumatic chisel • robust high performance chisel operated by compressed air for universal use in the laboratory. • high frequency chisel to deflask dentures and disinvest casting. • avoid, micro cracks formed by unconventional methods of plaster removal. • high quality compressed air control. • filter, lubricator, regulator, unit built in circu , facebow with semi adjustable articulator hanau wide view arcon articulator with spring bow, earpiece, face bow, orbital indicator, bite fork, mounting plates & other accessories , laser (hard tissue) hard tissue laser er,cr: ysgg laser, 0.1 9.0w(450 mj)10 50 hz, laser classification 4, voltage 100 230 vac , of wave length 2780nm erbium yag laser, pulse energy upto 700 mj, power upto 8.4 watt on tissue, frequency 10hz 50hz, wavelength 2940nm...

University Of Burdwan - West Bengal

36524842 tender for supply of minor instruments/consumables/teaching aids 1. minor instruments vertical laminar flow cabinet autoclave colorimeter vertical electrophoresis system transfer system microscope 2. consumables yeast extract powder, type i chloroform ni nta agarose beads micro tips 200 1000ul micro tips 0.2 10 ul petri dish (90 mm) pipette aid fixed volume pipette 10ul phenol:chloroform:isoamyl alcohol 25:24:1) glass pipette 1ml glass pipette 2ml glass pipette 5ml conical flask 250 ml measuring cylinder 250 ml measuring cylinder 500 ml reagent bootle glass slide cover slip test tube stand pcr teaching kit western blotting teaching kit protein estimation teaching kit quantitative) dna estimation teaching kit restriction digestion teaching kit karyotyping teaching kit cloning teaching kit 3. technical aid lcd overhead projector projector screen ...

Health And Family Welfare Department - West Bengal

24862123 re e tender for procurement of dental items used in dentistry for two years from the date of award of contract ( aoc ) 1 self adjusting endodontic file system(saf system)nnspecification:nndigitally controlled endodontic micromotor with peristaltic pump.n self adjusting root canal files, rotary motion with speed and torque control, nreciprocating motion with reverse/ forward angular movement 2 3rd generation apex locatornnspecification:nnwith lip clip, colour display module, file clip & associated chordnstandard packaging/physical verification of sample may be made 3 6th generation adaptive apex locatornnspecification:nnwith lip clip, colour display module, file clip & associated chordnstandard packaging/physical verification of sample may be made 4 acrylisernnspecification:nnfor 16 flasks or more stainless steel lined both outside & inside. temperature is controlled by thermostat from 5°c above ambient to 100°c with a sensitivity of + 5’c with timer can be set 1/2 hour to 2 hours.ndrain valve is provided for dewaxing. to work on 220/230 volts ac. 5 adam’s plier with tungsten carbide tipnnspecification:nnfor orthodontic work. n 6 adam’s pliernnspecification:nnfor orthodontic work. made of hard tempered steel 7 air polishernnspecification:nnair driven dental air polishing unit withreservoir hand held with connection to dental chair unit.n sterilizable up to 275°f (135°c), 44 psi. 8 aluminum slide traysnnspecification:nnmade of aluminumntray dimensions: 11.25 x 7.25 x 0.25 in.holds 20 each of 25 x 75 x 1mm slides 9 amalgamator with plungernnspecification:nn• input voltage 220 230vn• provided with touch pad selectorn• pre programmed time settingn• quiet, high speed mix capsulesn• built in automatic timern• capsule holder accepts all types of amalgam capsulen• with plungern• customized trituration times 10 anatomical articulatornnspecification:n n1. rust free construction. n2.fixed condylar guidance with spring mounted elements that are attached to upper membern3. incisal pin. 4. mid incisal pinn5. orientation rod,6. incisal guide tablen7. support upper & lower plaster cast 11 anterior jacquettennspecification:nnset of three.( 1 pc straight & two pc curved)nmade of high quality stainless steel. 12 austin’s retractorsnnspecification:nnl shaped with one rounded end and one forked end nmade of stainless steel 13 band pinching pliers setnnspecification:nnset of 1 piece each ofleft & rightnfor orthodontic work. made of hard tempered steel 14 band pushernnspecification:nnfor orthodontic work. made of hard tempered steel 15 binocular compound microscopennspecification:nnsharp image display with excellent optical function, small space occupancy with integral stand design, low environment requirement with anti mould technology.ncomfortable operation with ergonomic design principlenviewing head: compensation free binocular head inclined at 30o interpupilary distance 55 75mmneyepiece: wide field eyepiece wf10x/18mm with eye guard, achromatic objective 4x, 10x, 40x, 100x,nfocussing range: co axial coarse and fine adjustment range 13mm fine division 0.002mm with tension control.nnose piece: quadruple nosepiece,nstage: double layer mechanical stage 140 x 140 mm/ 75 x 50 mm n.a1.25 abbe condenser with iris diaphragm and filter. nfocussing: coaxial coarse & fine adjustment system range 24mm, fine division 2mmnillumination: led light with brightness adjustable. iso 13485 or ec certificate/directive 93/42/eec) 16 block holdersnnspecification:n nto be used to hold paraffin blocks and not made of plastic 17 blow torchnnspecification:nnfor casting procedure:nmade of non corrosive high fusing alloy nprovided with air flow regulator, two separate inlet line for lpg gas & oxygen 18 boley gaugennspecification:nnmade of stainless steel for measuring tooth dimensions & others. 19 bone expansion and splitting kitnnspecification:nnthe kit consists ofnosteotomes set of 5 6 of various diametersnspreadersn burs surgical for bone removaln saw discn thumb driver & rachetnautoclavable cassette 1 piece 20 bone file howard type nnspecification:nnstraight or curved working ends nto smooth bone for better contour of alveolar ridge crosscut or straight cutting ridges double ended nmade of stainless steel 21 bone file miller typennspecification:nndouble ended made of martensitic stainless steel 22 bone grafting syringe nnspecification:nnfor “tamp and pack” method for placement of graft material into oral cavity. 23 bone rongeur end cutting nnspecification:nnscissor type handle, cutting edges on top edge of beaks made of martensitic stainless steel 24 boon’s gaugennspecification:nnhigh quality stainless steel framework with minimumnmarking till 6mm 25 bracket debonding plier posteriornnspecification:nnfor band removal in orthodontic work. tungsten carbide tipped 26 brass flask size no 6nnspecification:nnfor acrylic denture fabrication by compression moulding, with detachable upper, body & lower member with keyways. made of brass 27 buck knifennspecification:nnsize ¾ & 5/6 for use in periodontal surgery 28 bur chuck for dental lathennspecification:nnof different shapes for attaching abrasive stone point, stone wheel & other attachments 29 camel hair painting brush size 04 30 canine contouring pliernnspecification:nnfor orthodontic work. made of stainless steel 31 casting ring extra largennspecification:nncasting ring extra largenmade of steel nfor use with centrifugal casting machine nlength 4 & diameter x 4.75or more 32 casting ring large nnspecification:nnmade of steel nfor use with centrifugal casting machine .nlength3 & diameter x 3.75 33 casting ring mediumnnspecification:nnmade of steel for use with centrifugal casting machine .nlength2 & diameter x 2.75 34 casting ring smallnnspecification:nnmade of steel for use with centrifugal casting machine .nlength1.25 & diameter x 1.75 35 casting tongnnspecification:nnmade of stainless steel or high fusing alloy for holding casting ring 36 cement mixing spatulannspecification:nnmade of stainless steel double ended 37 ceramic sculpturing & finishing kitnnspecification:nncomprising of high quality sable hair/ synthetic filament brush size one zero, two zero and four zero and other sizes, ceramic curver, mosquito forcep, tweezer, ceramic pallete for mixing ceramic powder and other associated carving & finishing instruments. 38 chandler chisel with 5mm tipnnspecification:nnwide single bevelled blade chiselnmade of martensitic stainless steel alloy 39 chin retractor obwegeser typennspecification:nnlength 15.5 cm, made of stainless steel 40 circular sawnnspecification:nnfor dental model cutting: with self illuminationnprovided with motor driven circular saw blade and cast holding platform, electrically operated motor driven with push button type on off switches. 41 clinical micromotor brushlessnnspecification:nnelectrically operated with handpiecenhandpiece autoclavable upto 135 degree celcius, handpiece speed 1000 40000rpm, speed maximum output power 1.2w,3.4 3.5 ncm torque,with option of clockwise & anticlockwise rotation.n control box and foot control mechanism. 42 colorado needle and accessories.nnspecification:nnelectrosurgical needle is needle electrode for use in monopolar electrosurgical handpiece made of tungsten carbide. coagulation tips & cutting tipsshould work with most of the diathermy units available in the hospital ,operating frequency above 3 mhz.niso/fda/ce 13485 or ec certificate(directive 93/42/eec) 43 composite curing unit systemnnspecification:nnfor indirect composite worknchamber provided with sliding tray, provided with multiple halogen or led lights light intensity not less than 900 mw/cm2output peak wavelength range 450 490 nm (intensity maximum at 460 nm)ncapable of curing indirect composite veneers/inlaysn. curing chamber dimension :nlength 10 inchesnwidth 7 inchesnheight 4 inches or morenelectrically operated 220 230 voltsnportable with timer 44 crane kaplan pocket marker nnspecification:nnpair of two instruments –right & left 45 crane kaplan scalernnspecification:n n double ended, round handled periodontal instrument for the removal of heavy supragingival calculus. it is a sickle type scaler, with a strong, rigid, sharply angled blade 46 crown gauge (iwanson caliper)nnspecification:nnfor measuring thickness of wax pattern, metal casting.nboth sided scale 0 10mm 47 crucible for small castingnnspecification:nnmade of fused silica/ceramic material, capable of withstanding high temperature for use with centrifugal casting machine 48 curing pressure potnnspecification:nn5 liter or more capacity npressure pot temperature is preset to approximately 120°fand manually adjusts to a maximum 160°f. nsolid clad bottom provides even heat distribution. nincludes an easy to read, built in pressure gauge and quick release air valve.nthe pot has a safety device to prevent overheating, and a secure double locking lid. neasy to clean stainless steel interior. npot holder to keep pot firmly nin place. nwith lid gasket 49 dappen dish made of glass 50 dental dewaxing unitnnspecification:nnwith digital control for water temperature regulation. construction: stainless steelntank sizes (300 x 200 x 350 mm) approximatelynwater filling: manual heater: 2000 watts. with drain valve 51 dental lathe motornnspecification:n nac, hp 1, universal, rpm 2800, equipped with double b.b, single speed, rating continuous with 3 chucks (buffer, stone & bur chuck), three imported b.b. flexible metal cable arm and its attachment. 52 dental muffle furnacennspecification:nn1150c degree celsius, working temperature 900 degree celsius, with er & digital displaynmuffle size 175x175x225mm. 4.0 k.w. capacity 53 dental phantom head unitnnspecification:nnmanikin head fixed with a table, with mounted upper & lower jaw containing screw mounted teeth having 90° swiveling function of head unit, provided with control box for micromotor, foot control & micromotor with contra angle handpiece, should have mounted light unit with illumination power not less than 7000 lux. 54 dental plaster dispensernnspecification:n nbody made of stainless 304 grade, fitted with digital electronic timer, capacity 5 kg or more. will dispense premeasured dose of plaster at touch of a button. 55 dental steam cleanernnspecification:nnpower 1500w or more, 220v, frequency 50/60hz. working pressure: 4 5 bar. capacity 5 10litre. with thermostat controller.device with both steam gun & button/lever controlled steaming attachment with steam regulator. stainless steel non rusting inner tank body. 56 dental surveyor tool kitnnspecification:nntools nanalyzing rod multiple undercut gaugesn carbon marker sheathn wax trimmer 57 dental surveyor ney’s typennspecification:nndental surveyor ney’s type nhorizontal platformn• adjustable spindle for the vertical indicator n• survey table that can be locked at any angle.nwith tools analyzing rod undercut gaugesn carbon marker sheathn wax trimmer etcnprovision for holding micromotor handpiece nstandard packaging/physical verification of sample may be made 58 dental vacuum former machinennspecification:nnelectrically operated, with inbuilt vacuum motor suction unit, heating element with on off switches & adjustable clamping plate.nspecifications:nvoltage : 230v/50 60hz npower : 600w 230v nheater : 400w 230v ndimension : l 23 25 cm, w 17 20 cm 59 endodontic explorer nstraight mono angled (stainless steel), adult standerd size to be addednn 60 diamond glass marker nnspecification:nnmounted in aluminum pencil 5 inches (12.7cm) 61 die cutting machinennspecification:nnelectrically operated with diamond disc. nwith adjustable model holdernself illuminated chamber 62 dingmans retractornnspecification:nnwith three blades made of stainless steel 63 dontrix gaugennspecification:nnspring balance type, minimum measurement till 500ngms to precisely calibrate orthodontic force there are two units of measurement ounce and gram. measuring range: 0 450g/0 16 oz. to measure tension and compression force 64 double wax heater potnnspecification:nnwith thermostat controlled temperature regulator electrically operated 65 dry model trimmernnspecification:nn with attached suction unit 66 duplicating flasknnspecification:nn a. programmable brushless agitator motorntemperature controls for precision warm up and cool down phasesnintelligent heating strategy and provision for effective disposal of gel and prevention of nozzle blockagenmaintainance of consistent gel qualitynvoltage: 200230v, 50/60hz,nb. pressure compaction unit for duplicating silicone materialsnautomatic mixing and metering unit for two component silicone materialnduplicating flask:n(a) individual aluminium duplicating flask with aluminium top and rubber base and 2 base formers (2 sizes)n (b) duplicating flask with stabilizing insert and three replaceable palatal formers of different sizes 67 electrically operated wax carvernnspecification:nnelectrically operated electrical wax curver with thermostat controller. with two detachable carving tools 68 electro polishernnspecification:nnautomatic digital electro polisher, auto/manual modes, nwith trimmers, electrolyte flow regulationn38 mm disc for psa paper & clothsnsupply 230 v. acncurrent – 2.5 amp., voltage – 80v, supply – 230 v.a.c.polishing probes – unique pen type system with recirculation of electrolyte, pump 25 watts reservoir (0.5 ltr) 69 endo activatornnspecification:nnsystem kit that includes handpiece/drivernbox of small, medium & large activator tips. nbox of 100 protective barriers. safe & vigorous energetising intracanal irrigant, capable of debriding & disinfecting root canal system 70 endodontic microsurgical equipment nnspecification:nncomprising of na. ultrasonic piezoelectric scaler with inbuilt irrigation , led & water tanknb. ultrasonic endodontic retro surgical tips (for anterior teeth upper & lower and posterior teeth of upper and lower arch)nc. ultrasonic passive irrigation, nd. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal 71 endomotor with torque control nhand piece.nnspecification:nncontinuous &/or reciprocating motions for root canal shaping, hand piece with integrated on off switch, auto reverse mode, speed 250 1200 rpm.n torque range 0.6 4 ncm,n multiple adjustable programsnstandard packaging/physical verification of sample may be made 72 endovac irrigation systemnnspecification:nn multiple port adapters, hand piece set, extra evacuation system, cannulas, delivery tips & syringes. 73 excavator oval type 74 excavator spoon typennspecification:nnexcavator double ended spoon type 75 extraoral gothic arch tracernnspecification:nnjaw movement recording and centric relationnpositioning, one stylus and one tracing platenattachments to the jaw movement recording basesnoutside the mouthnstandard packaging/physical verification of sample may be made 76 fiber optic lightnnspecification:nnfiber optic based lighting unit consisting of fiber optic cable, led based portable light with controller unit. with rechargeable battery niso 13485 or ec certificate(directive 93/42/eec) 77 flask clamp for brass flasknnspecification:n nmade of steel with clamp compatible with brass flask of size no 6 78 amalgam curver nstandard size triangular cutting blade, stainless steel.n 79 furcation curettes quetinnnspecification:n nbuccal lingual 0.9mm 1pc quetin buccal limgual 1.3mm 1pcnquetin mesial distal 0.9mm 1 pc quetin mesial distal 1.3mm 1pcnconform to iso 13485:2003/ en iso 13485:2012 80 gardner chisel with 3mm tipnnspecification:nnsingle bevel chisel nmade of martensitic stainless steel alloy 81 gates glidden drill setnnspecification:nnstainless steel, drill compatible with latch type handpiece for use in bulk removal of the tooth structurenunit pack containing six different sizes each drill having 28 32 mm length. 82 gillie’s skin hook single prong nnspecification:nnmade of stainless steeln 83 glass bead sterilizernnspecification:nnelectrically temperature regulated to heat contained glass beads with on off switch. nsmall rectangular base for keeping at chairside nprovided with lid. n it should reach operating temperature of approximately 240 c to 270 c in 15 20 minutes time. nsterilization is on contact with glass beadsnunit can be left in the “on” position all day and is safe for use in laminar flow cabinets. 84 glass slab 8mm thicknnspecification:nntransparent rectangular glass slab thickness 8mm, length 6” x 4” inch 85 glass slab bignnspecification:nntransparent square glass slab thickness 4mm, each side of 6 inch 86 glass slab smallnnspecification:nntransparent square glass slab thickness 4mm, each side of 3.5 inch 87 goldmanfox periodontal probennspecification:nndouble ended probe, markings at 1,2,3,5,7,8,9& 10mm.high quality stainless steel with satin finish, antimagnetic rust resistant, acid resistant 88 gracey curette setnnspecification:nnof 9 size ½, ¾,5/6,7/8,9/10, 11/12,13/14, 15/16, 17/18.made of hard tempered steelndouble endednhandle 10.2 10.8cmnshank 3.1 3.6cmnlength 6.8 7.4mmnoffset blade beveled at 60 70 degree to the shankn1.triple tempered steeln2.satin steel handlen3.corrosion resistantn4.rust resistantn5.stain resistantn6.can be sharpened by traditional sharpening stonesnconform to iso 13485:2003/ en iso 13485:2012 iso 13485 or ec certificate(directive 93/42/eec)ce & fda aprroved 89 guarded nasal chisel set of right &leftnnspecification:nnsize : 4, 5, 6, 8mm right & left in pair made of stainless steel 90 half round pliernnspecification:nnfor orthodontic work. made of hard tempered steel 91 hand scaler set of 5 piecennspecification:nnset containing 1 piece each of: sickle, push, universal, broad right & left . 92 hard wire cutternnspecification:n nhard wire cutter made of tungsten carbide tipped 93 heavy duty lathe with suction unitnnspecification:nnelectrically operatedheavy duty motor unit having power not less than – 0.5hp nhigh speed r.p.m. 3000 rpmnarrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided withnbuilt in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection.ntable mountable heavy base plate for vibration free operationnbuilt – in lighting for high visibility 94 hinge articulatornnspecification:nnrust free constructionnpermit opening & closing in hinge like motion. support upper & lower cast.n upper member adjustable with locking nut. 95 hook crimping pliernnspecification:nnfor orthodontic work. made of stainless steel 96 hot plate with wooden handle 97 howe’s pliers anteriornnspecification:nnwith serrations, useful for placement and removal of archwires, pins and other auxiliares nmade of stainless steel 98 howe’s pliers posteriornnspecification:nnpliers with serrations, useful for placement and removal of archwires, pins and other auxiliares 99 hydraulic pressnnspecification:nnthe closed circuit hydraulic press should work with a pressure up to 7000 kg of thrust.n it can contain up to three flasks at a time. nthe structural elements in chromium plated steel.n provided with dial. 100 hydro soldernnspecification:nnmains voltage: 1 x 230 v,mains frequency: 50 x 60 hz, mains fuse: 1 x 10. anmax.gas production: 6 liternmax. nozzle size: 0.07mmn dimensions w x h x d x (mm): 330 x 230 x 310 mmnweight: 22 kgncapacity: 110lt, with accessories 101 implant microsurveyor nnspecification:nnwith compass surveying system, portable hand held surveyor 102 inlay wax curver double ended 103 instrument sharpening kit with arkansas stonennspecification:nn flat arkansas stone with conical shapenplastic test stick(5)nstone oil nmagnifying lens& other accessories 104 intra oral camera with video monitornnspecification:nna)camera:neasy to use, narrow head, comfortable for patient intra oral camera with provision of variable lens adjustment that can be attached to dental chair unitnvideo compatible so that images can be displayed on a computer workstation/lcd monitornstill image resolution: 1024 (h) x 768(v) or morenvideo resolution: 640 (h) x 480 (v) or morenfocus range: 1 mm 25 mmnlens surrounded by led lampninput: 220v 50 60hz noutput: 5v, 2a 105 intraoral camera with fluorescent technologynnspecification:nnintra oral camera with caries detection and periogingival inflammation detection facility based on flurescent technology 106 intraoral sand blastern(microetcher)nnspecification:nnlong tubing with compatible adapter for the airotor handpiece pointnof the dental chair, fully autoclavable, 50 micronsnaluminium oxide particle size, 360 degree adjustable nozzle. 107 intraoralgothic arch tracernnspecification:nnjaw movement recording and centric relationnpositioning, one stylus and one tracing platenattachments to the jaw movement recording basesninside the mouthn 108 kirkland gingivectomy knifennspecification:nnfor use in periodontal surgery n 109 laboratory micromotor with brushless motornnspecification:n ncompact and portable size, continuous variable speed control , r.p.m 1000 40000,on/off foot switchone touch change of the driving direction for efficient operation with brushless motor with handpiece 110 laboratory micromotor with carbon brush motornnspecification:n ncompact and portable size, continuous variable speed control , r.p.m 1000 40000,on/off foot switchone touch change of the driving direction for efficient operation with carbon brush motor with handpiece 111 laser guided pin drilling system with pinsnnspecification:nnelectrically operated 110v/240v, laser guided pinsetter, pin drilling for easy die pin attachment. nlaser light technology with carbide bur drill with high speed motor. nto accurately drill parallel holes into the underside of the model die pins of various sizes(1000 pieces total) made with non corrosive alloys for use with pindex system of die pins. 112 lead apronnnspecification:nnadult size, 0.5 mm thick lead covered with cotton onnboth sides, overstraps, buckles & hand gloves (size 6nto 7.5) with 0.5 mm thickness lead 113 lecron wax curvernnspecification:nnmade of steeln 114 leuckhart piecesnnspecification:nntwo l shaped metallic stands for preparing paraffin wax block 115 light cure unitnnspecification:nn led based. light modes fast, ramped & pulsedndisplay for mode & timernselectionnchordless with rechargeable lithium battery nlight intensity not less than 1200 mw/cm2output peak wavelength range 450 490 nm (intensity maximum at 460 nm)nwith inbuilt timer, on off switch 116 magnification loupes 3.5xnnspecification:nnergonomically designed binocular loupe that can be worn over spectacle frame capable of 3.5x magnification at 420mm with 3watt led rechargeable light 117 magnification loupes 4.5xnnspecification:nnergonomically designed binocular loupe that can be worn over spectacle frame capable of n4.5x magnification at 420mm with 3watt led rechargeable light n 118 magnifying work lampnnspecification:nnwith flexible & adjustable stand and base. inbuilt led based optical illumination system. nglass lens diameter 7 inches or more, magnification power upto 4 x 119 manual crown removernnspecification:nn with adjustable spring with crown remover tip ¬ 2 single crown remover contrangled tip ¬ 3 open¬end adjustment wrench 120 manual pressnnspecification:nnwith base and cross bar made with high strength steel.nthe structural elements made with chromium plated steel.ncapable of pressing upto 1 to 3 flasks at a time.nbase should have holes for attachment to bench 121 marquis colour coded probennspecification:nnfor periodontal surgery made of stainless steel colour coded at 3 6 & 9 12 mm 122 mathieu pliernnspecification:nnstraight & curved for orthodontic worknused for ligature typing and placing of elastics 123 mbt gaugennspecification:nnfor .022” slot nfor orthodontic work. made of stainless steel 124 metal impression tray non perforatednnspecification:nnmade of non corrosive alloynfor edentulous patient set of upper & lower, size 0,1,2,3,4.n(price being same to be supplied as per requirement of user) 125 metal impression tray perforatednnspecification:nnfor dentulous patient nmade of non corrosive alloynset of upper & lower, size 0,1,2,3,4.n(price being same to be supplied as per requirement of user) 126 metal suction tipnnspecification:nna)3mm diameter 10 pcnb)5mm diameter 10 pcnmade of stainless steel 127 micro oscillating saw nnspecification:nncapable of easily cutting channels and bone blocksnmaximum 12,000 oscillations per minute. compact design for easy access .ntwo shaft lengths & 4 blade sizes for optimum access.nincludes external irrigation port for effective bone coolingnuniversal e type coupling that fits implant motor unit 128 microhead air rotor handpiecennspecification:nnsuitable for use in child patient, head size 8.5 x 19.4 mm, provided with water spray, body made with ceramics autoclavable, rotational speed 3,00,000 to 450,00,00 rpm, provided with a bur changer & wrench.nphysical verification required 129 microvascular instrument kitnnspecification:nnkit comprises of n1.micro scissorsn2.micro needle holdern3.jwellers forcepsn4.vessel dilatorsn5.liga clips(no.100.no.200)n6.ligaclip applicatorsn7.vessel clamp (2a,2v,3a,3v) n8. vessel clamp applicatorn9. hand held colour doppler unitn10.pneumatic tourniquetnspecification to be quoted by the bidder / manufacturernmicro scissors ni) adventitia scissors flat handle , 8mm wide, straight length of 15cms, blades 19mm – 5 pcsnii) dissecting scissors – flat handle, 8mm wide , curved,length of 15cms, blades 19mm – 5 pcs niii) adventitia scissors round handle, 8mm diameter of tip,straight, length 15cms, blades 12mm – 5 pcsniv) dissecting scissors – round handle, 8mm diameter of tip,curved, length 15 cms, blades 12mm – 5 pcsnmicro needle holder:ni) flat handle , 8mm wide, curved, 14 cms length – 6 pcsnii) round handle, 8mm, curved, 15 cms length – 6 pcsnjewellers forcepsni) flat handle , 9mm wide, straight, 13.5 cms length – 6 pcsnii) flat handle , 9mm wide, angulated 45 degrees, 13.5 cms length – 6 pcsniii) round handle , 8mm wide, straight, plateau, 15 cms length – 6 pcsnvessel dilators:ni) flat handle , 9mm wide, angulated 10 degrees, nlength 11cms – 6pcsnliga clips – made of stainless steel, autoclavable.nno.100 – 150 sets ( each set containing 6 liga clips)nno.200 150 sets ( each set containing 6 liga clips)nno.400 – 100 sets ( each set containing 6 liga clips)nligaclip applicator:ngrooves on inside jaw surfaces of applier which helps in increasing of jaw clip security.nangled jaws to improve visibility beyond structuresnmechanical stop.nmade of stainless steel and autoclavable. 130 mini pin & ligature wire cutter nnspecification:nntungsten carbide tippedncuts soft wire pins and ligature wire up to .012”(.30 mm) 131 miscellaneous hinnspecification:nn139 plier for orthodontic work. made of stainless steel 132 miscellaneous hi 133 model trimmer with carborundum discnnspecification:nnmotor rpm 2800 heavy duty, equipped with two ball bearing single speed, rating continuous with buffer and 10 carborundum disc , with heavy base that can be clamped and installed on underlying table,with water inlet and out flow water system. 134 model trimmer with diamond discnnspecification:nn1/2hp, rpm 2800, heavy duty equipped with two ball bearings, single speed, rating continuous with buffer and one 10 diamond disc rough or fine without suction.1 piece spare diamond disc to be provided 135 model trimmer with double discnnspecification:nnone diamond & one carborundum discn rpm 2800 double motors horsepower 1/2 or more each, heavy duty, equipped with two ball bearings each motor, single speed, rating continuous with fixed one10 diamond disc fine, one carborundum coarse cutting wheel, base inlet, with outflow water system. 136 molts elevatornnspecification:nnlength 7”double ended with one round, blunted end and one pointed end made of stainless steel 137 mouth propnnspecification:nnautoclavable made of stainless steel with rubber pads for intra oral use over occlusal surfaces during surgery. the rubber pads are of 4 sizes attached by a stainless steel chain. 138 naber’s probennspecification:nnfor use in periodontal surgery double ended furcation probenconform to iso 13485:2003/ en iso 13485:2012 139 omega loop forming pliernnspecification:nnfor orthodontic work. made of stainless steel 140 orban gingivectomy knifennspecification:nnfor use in periodontal surgery n 141 oschenbein chisel curvednnspecification:nnsize no. 1 and no. 2 ochsenbein chisels periodontal chisels. they havethree cutting edges, a flat edge on the tip and a curvededge on each side of the tip. 142 oschenbein chisel straight nnspecification:nn17.5 cm x 4 mmnsize no. 1 and no. 2 ochsenbein chisels periodontal chisels. they havethree cutting edges, a flat edge on the tip and a curvededge on each side of the tip. 143 osteotome 20mm nnspecification:nnmade of stainless steeln 144 paeso rimmer drill setnnspecification:nnstainless steel, drill compatible with latch type handpiece for use in bulk removal of the tooth structurenunit pack containing six different sizes each drill having 28 32 mm length. 145 palatal trimmer nnspecification:nnprovided with1 fast cutting trimmer, electrically operated ,rpm 2600 or morenbody made with 304 grade stainless steel, or non rusting alloy. dull finished work surface, dust collection with adapter hose, provided with1 fast cutting trimmer 146 paquette blade handlenhead dimension 2 cm. length. 15 cm. , made of s.sn 147 paraffin wax bath (thermostatically controlled)nnspecification:nnconstruction – double walled effectively insulated.wax tank of 20 gauge ss sheet. fitted with laminated wooden rim and anodized alumininium cover mounted on 5 cm diameter.nheater two 1 kw each special wax heater.nheat control thermostat to control temperature from 30 degree c to 110 degree cnfinish externally finished in oven bakednaccessories power plug, 1 brush for wax application and aluminium sheet mesh for heater.n 148 pediatric extraction lower incisors & canine forcepnnspecification:nnmade of hard stainless steel with knurnled handle grip,disc type of hinge joint, 4.5 inches of length 149 piezo surgical kitnnspecification:nn device with intermittent operation, 60 sec on then 30 sec off with irrigation, & 30 sec on 120 sec off without irrigation, power supply 240v,50/60 hz, maximum power absorbed 120va. surgical tip capable of modulating from 10 to 30 or more. 29khz or more. power adjustable from 2.8 to 16w. tip vibration in range of 60 200µm.motor with tips & other accessoriesn(european ce/ fda (usa)approved) 150 pikling kitnnspecification:nnelectrically heated and thermostatically controlled pickling unit for acid based pickling agents with low power consumption for pickling of precious metals. swivel sieve and housing made of shock proof and acid resistant polypropylene material 151 plaster knifennspecification:n nwith working length not less than 2 .5inches 152 plaster spatulannspecification:nnround ended steel spatula having width of 1.25 inch & length 5 6 inches, with plastic or wooden handle 153 plastic filling instrumentnward type 154 pneumatic crown removernnspecification:nnpneumatic, autoclavable tips, basic kit includes easy pneumatic crown and bridge remover bridge remover tip ¬ 1 single crown remover tip ¬ 2 single crown remover contrangled tip ¬ 3 open ¬ended adjustment wrench rubber gasket flexi¬wire set 155 pneumatic deflasking unitnnspecification:n n operates on air pressure.nwith handheld chisel provided with detachable tips n provided with variable powercontrol with air inlet and tubing length not less than 1.5 meter.nworking pressure 1 6 bar 156 portable transcutaneous electrical nerve stimulation (tens)nnspecification:nnunit for pain management with replacement electrodes. the machine should have burst, continuous and modulation pulse modes. dual, isolated between channels with a pulse intensity of 0 80ma peak into 500ohm load. pulse rate of 2 120hz adjustable. pulse width 40 260 microseconds, adjustable. maximum voltage: 110v. maximum charge: 21microcoulombs per pulse 157 pressure moulding machine nnspecification:nnthe unique thermally controlled heater reaches working temperature in few minutes.npower: 230 v, 850 wnworking pressure: 0,5 – 6,0 barnmeasurements (w x h x l): 450 x 230 x 260 mm 158 pulp tester digitalnnspecification:n npreset stimulus speed mode, battery 9v, auto off after 3 min, with autoclavable tips, one touch operation, with digital read out of display 159 rme bendernnspecification:nnfor orthodontic work. made of stainless steel 160 robinson black bristle brushnnspecification:nnhaving diameter of not more than 2.5 inch. 161 root canal explorernstainless steel (cow horn design)n 162 rowe zygomatic elevatornnspecification:nnmade of stainless steel (standard adult size)nn 163 rubber bowlnnspecification:nnsize largen13 cm in height made with flexible synthetic rubber material 164 rubber dam kit nnspecification:nnrubber dam clamp forceps nrubber dam punch nrubber dam frame adult nuniversal rubber dam template nfdi rubber damnprovided with different clamp designs such as molar clamps, bicuspid clamps winged, labial clamps wingednit contains:n plastic dental dam frame 6/5n wedjets stabilizing cord pack(s)n hygenic template 6/5n punchn forcepn rubber dam sheets 6x6(36)/pedo 5x5(52)n set of 9 clamps adult/set of 6 pedo 165 sand blaster unitnnspecification:nnself illuminated chamber. unit with ventilation slits with rubber gloves, pressure regulator, air filter ,provided with glass pane. flow of blasting material from 1 to 6 bar. with wear resistant nozzle tip attached with wear & tear resistant hoses & nozzles. with filter. micro & macro mode 166 sanders periodontal knife nsize 1/2 n 167 schluger bone file for use in periodontal surgery 168 self retaining retractor weit laner typennspecification:nn made of stainless steeln 169 semi adjustable articulator with accessoriesnnspecification:nnwide view arcon articulator with spring¬ bow, ear¬piece, face bow, orbital indicator, bite fork & other accessoriesnstandard packaging/physical verification of sample may be made 170 separator placement pliersnnspecification:nnfor orthodontic work. nmade of hard tempered steel 171 sinus lifting instrument kitnnspecification:nnfor lateral & crestal approachn with s reamer/lateral reamersninitial drill/crestal drillsn bone inserternbone spreadern bone carriern bone condenserndepth gaugen chisels of different widthn sinus curettes of various designsn bone rongeur forcepsnmallet nirrigation syringe & tipsn& other instrumentsnautoclavable cassette 1 piece 172 slide storing cabinetnnspecification:nncabinet for 1050 slides consisting of 6 drawers each for 175 slides, arranged in single rowframework made of 15mm plywood with top and sides covered with sunmica laminated sheet. 173 slide warming tablennspecification:nntop surface made of stainless steel (ss 304 grade)nthe surface temperature is controlled from ambient to 70°cnsupplied complete with pilot lamp, cord and plugnto work on 220/230 volts a.c. supply 174 spirit lampnnspecification:n nmade of stainless steel nof 100 ml capacity with wick & detachable cap stainless steel body 175 spot welder with soldering attachmentnnspecification:nn• electrically operatedn• voltage110 240 voltsn• applications / indication spot weldingn• power settings2,000 amperesn• heat settings2n• electrode / tip type hand electroden• welding positions adjustable 176 steel slide racks for stainingnnspecification:nn the 5 slide gripper can accommodate 5 microscope slides in one staining procedure.it fits most coplin and round open staining jarsnit should be made of a special material which is resistant to all chemicals and solvents which are used in stainingnit withstands drying temperatures up to 80°c 177 step pliernnspecification:nnfor orthodontic work. made of hard tempered steel 178 surgical elevators cryer’s patternnnspecification:nnmade of hard stainless steelnlength 145mm, neck diameter 3.6mm, working tip length 9mm for right & leftnset of 2 units cryer’s right, left 179 surveyor mounted miling machinennspecification:n nuniversal precision milling unit. areas of application; wax milling and scraping ; milling, fine grinding, drilling and smoothing of metal with the help of the modeling spindle, it can be used as a surveying instrument and for mounting auxiliary parts. magnetic locking device for model table. drilling depth stop and connection facilities for additional handpiece for finishing. advantages: universal design for measuring, blocking and routing (router head accept spindles, drawing tools and measuring tools). easily movable double articulating arm free from play. routing spindle with quick coupling. controllable, heatable wax knifenrpm can be infinitely controlled from 3000 to 35000 rpm. left/right rotation. route head with micrometer screw for exact vertical bores. good illumination due to integrated led light iso 13485 or ce certificate 180 three prong pliernnspecification:nnfor orthodontic work. made of stainless steel 181 tissue biopsy kitnnspecification:nn1.small and short scalpel blades (no. 15, 11, 12 or even 5) –n 2. mosquito forceps – 2 pc curved & 2 pc straightn3. gauze container made of stainless steel size small 1pcn 4. alley’s tissue forcep 2pcn5. punch biopsy set one piece of three different diameters (circular blade size 3 mm, 5mm & 7 mm) in each kit n6. mc indoe’s dissecting scissor1pcn7. bone scoop small1pcn8. bone curette tip diameter 3 mm 1pcn9. sklar tungsten carbide bozeman 10.needle holder 8 tungsten carbide tipped 1 pc with catch,n11. wards needle holder 1pcn12. toothed dissecting forcep 1pcn13. non toothed dissecting forcep 1pc 182 tissue capsules / tissue embedding cassettesnnspecification:nnmade of acetyl polymer;cassettes should keep specimen safely submerged in liquid, efficient flow through slots,snap latch and hinge lock design prevent early separation of base and lid and allows for one hand operation. large labeling area on two sides of cassette. anterior writing area is at 35° angle.npore size: 1mm square poresnoutside dimensions: 28.5 x 41 x 6.7mm (1.12 x 1.61 x 0.26)ninside dimensions: 26 x 30 x 5mm (1.02 x 1.18 x 0.2) 183 tissue floatation water bathnnspecification:nn(thermostatically controlled) inner tank (single piece) made of black anodized aluminum. housing made of powder coated aluminum. front panel consist of temperature regulator knob, mains switch and pilot lamp. inside black and outer surface finished in powder paint, with wide enough rim for drying the wet slides.nbath size(inner) 225mm*70mmntemperature controlled by capillary tube thermostatntemperature range n+5 degree c to 70 degree c 184 torch, alcohol, dental nnspecification:nnwick volume capacity 90ml or more, with adjustable needle point flame, body metal or plastic 185 torquing pliers malennspecification:n nfor orthodontic work. made of stainless steel 186 torquing pliers malennspecification:n nfor orthodontic work. made of stainless steel 187 tourniquet armnnspecification:nnhaving pressure regulator, tubing and connectors with not less than7 cm inflatable cuff 188 tourniquet legnnspecification:nnhaving pressure regulator, tubing and connectors with wide 14 cm inflatable cuff 189 towel cross section clipnnspecification:nnmade of stainless steel used to fix drapes to tissue with minimal trauma during surgical operations 190 tracing tablennspecification:nnbox portable with opaque screennlight box with led nelectrically operated with ajustbale illumination. box dimension 14” x 16” or more 191 transparency scannernnspecification:nndual lens system, minimum 6,400 dpi opticalnresolution, 4.0 dmax for smooth gradation and finenshadow detection, antireflectivenoptical coating andnhigh reflection mirror, digital ice technology, 8” x 10”ntransparency unit built into lead 192 trephine bur setnnspecification:nn of 3. dia 2,3,4mmnfor harvesting bone cores for use in periodontal surgery iso 13485 or ec certificate(directive 93/42/eec) 193 turretnnspecification:nnzero torquenfor orthodontic work, made of stainless steel. n 194 tweed pliernnspecification:nnfor orthodontic work. made of stainless steel 195 typhodont articulatornnspecification:n narticulated model with soft pink (not transparent) acrylic or plastic gingiva material. included:28 anatomically shaped screwable typhodont ivorine teeth 196 ultrasonic cleanernnspecification:nn 220v, 100 200watt & above, 5 liter capacity, with stainless steel body &cover. 197 ultrasonic dental scaler nnspecification:nnelectrically operated 220/240v 50/60hz ac with control box,multi frequency handpiece with scaling tips,foot control,water connector, tube & other accessories. capable of upto 20khz ultrasonic vibrations/second or moreniso 18397:2016/ iso/fda/ce 13485 or ec certificate 198 unc 15 periodontal probe plasticnnspecification:nn probe with markings at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15colour coded at 5,10 & 15mm, thin shanked probe 199 unc 15 periodontal probe: titaniumnnspecification:nnprobe with markings at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15colour coded at 5,10 & 15mm, thin shanked probenconform to iso 13485:2003/ en iso 13485:2012 iso 13485 or ec certificate(directive 93/42/eec) 200 universal columbia curettennspecification:nncommon properties:n1.triple tempered steeln2.satin steel handlen3.corrosion resistantn4.rust resistantn5.stain resistantn6.can be sharpened by traditional sharpening stonesn7.properly designed & balanced handles to reduce chances of “carpal tunnel syndrome”na) in different sizes nhandle 10 11cmnshank 2.7 3.2cmnblade length 5.8 6.5mm, width 1.3 1.6mm,90 degree offset anglensemicircular cross section with convex base nb) in sizes of sc4r/4l6nhandle 10 11cmshank 2.9 3.4 cmnblade length 5.8 6.5mm, width 1.3 1.6mm,n90 degree offset anglensemicircular cross section with convex base. 201 university of michigan o probennspecification:nnfor use in periodontal surgerynsingle ended probe with markings at 3 6 8mm 202 upper canine extraction forcep english pattern nnspecification:nnmade of hard stainless steel with knurnled handle grip, disc /box type of hinge joint 203 upper incisor extraction forcep english patternnnspecification:nnforcep made of hard stainless steel with knurnled handle grip,disc /box type of hinge joint 204 upper molar extraction forcep english patternnnspecification:nnmade of hard stainless steel with knurnled handle grip, disc /box type of hinge jointnset of one piece right & one piece left upper molar forcep 205 uv sterilisernnspecification:nndimensions of cabinet: 22 x 12 x 8”nfront door with uv protected glass window & magnetic door sealnprovided with multiple tray racks not less than fournelectrically operatednprovided with uv light source 206 vacuum investment unitnnspecification:nncapable of mixing unit amount of investment material under vacuum through a motor 207 vacuum mixing machinen nspecification:nn1. vacuum mixing machinenfor mixing investment material n2. electrically operated motor 1500 watts or moren3. compactn4. automatic regulation of the vacuum n5. the mixing motor remains clean and is easily serviced due to a supporting filter and a fine filter in conjunction with the maintenance free vacuum pumpn6. direct connection between mixing bowl and vacuum pump – no disturbing exterior hosen7. mechanical coupling tolock the mixing bowl in positionn8. a mixing bowls (500 g )niso 13485 or ce certificaten 208 vibratornnspecification:nn• electrically operated size 4.5 x 8 x 6.5 inches or moreplatform shaperectangular, type heavy dutyn• constructionenamel painted body with rubber plate above body,speed: 3 speed vibration controllern• platform shaperectangular 209 warwick james elevatorsnnspecification:nnmade of hard stainless steelnset of 3 units right, left & straight tips 210 wax block storing cabinet nnspecification:nncabinet made out of duro board, externally clad in laminated sheet. dust proof door is lockable. provided with smoothly sliding drawers with sixteen compartments each of size 4x4x2 and have puller knobs. each compartment can store blocks in two rows. 211 wax burnout furnacennspecification:nnmaximum temp 1200c working temp 1150c with digital display cum temperature controller with safety alarm nmuffle size : 175x175x225mmn 4.0k.w 212 wax curver: pkt typennspecification:nnset of 5 instrumentsn 213 wax knifennspecification:nnmade of stainless steelnwith one end bearing knife pointed & other thick, flat with curved end 214 wax spatulannspecification:nnmade of stainless steelnwith one end pointed & other end curved 215 weingart pliernnspecification:nntungsten carbide tippedn 216 who probennspecification:nna. clinicalnb. epidemiologicalnna. clinical – 0.5 mm ball at the tip, making at 3.5mm,8.5mm,11.5 mm, colour coding 3.5 5.55 mmnweight – 5 gmnb. epidemiological marking at 3.5 mm & 5.5 mmn0.5 mm ball at the tip 217 williams probennspecification:nnfor use in periodontal surgeryth marking at 1,2,3,5,7,,9 & 10mm 218 wire tuckernnspecification:nnfor orthodontic work. tungsten carbide tipped 219 wooden / plastic slide boxesnnspecification:nnframework with finger joints fabricated out of teakwood with sunmica top and plywood bottom. wooden grooves for standing 3”x1” glass slide in vertical position individually. inside bottom covered with velvet and inside top with printed index. provided with brass chromium plated hinges clips and card frame. finished in natural color niro cellulose lacquer. 220 wooden malletnnspecification:nnhaving wooden head that is10 cm in length, round at one end of diameter 3 cms while tapered at other end, handle length 28 cmsnfor prosthodontic laboratory use 221 woodson periosteal elevatornnspecification:nndouble ended one end curved(curved working end length: 10 14 mm, width: 5 6mm)nflat tapered end: length – 14 16 mm, width at the widest point 4 6 mm ...

Health And Family Welfare Department - West Bengal

21578709 e tender for procurement of dental items used in dentistry for two years from the date of award of contract ( aoc ) 1 3rd generation 2 6th generation 3 acryliser n 4 adam’s plier with tungsten carbide tip n nspecification: n nfor orthodontic work. n 5 adam’s plier n 6 adson forceps, toothed n 7 adson’s forceps non toothed n 8 air polisher n 9 aluminum slide trays n nspecification: n nmade of aluminum ntray dimensions: 11.25 x 7.25 x 0.25 in.holds 20 each of 25 x 75 x 1mm slides 10 amalgam carrier n nspecification: n nmade of stainless steel 11 amalgam plugger n nspecification: n nmade of stainless steel double ended 12 amalgamator with plunger n nspecification: n n• input voltage 220 230v n• provided with touch pad selector n• pre programmed time setting n• quiet, high speed mix capsules n• built in automatic timer n• capsule holder accepts all types of amalgam capsule n• with plunger n• customized trituration times 13 anatomical articulator n nspecification: n n1. rust free construction. n2.fixed condylar guidance with spring mounted elements that are attached to upper member n3. incisal pin. 4. mid incisal pin n5. orientation rod, 6. incisal guide table n7. support upper & lower plaster cast 14 anterior jacquette n nspecification: n nset of three. ( 1 pc straight & two pc curved ) nmade of high quality stainless steel. 15 apexo elevators n nspecification: n nset of two set of right & left made of stainless steel. 16 austin’s retractors n nspecification: n nl shaped with one rounded end and one forked end nmade of stainless steel 17 babcock’s forcep n nspecification: n nfinger ring, ratcheted, non perforating forceps used to grasp delicate tissue nmade of stainless steel 18 band contouring pliers n nspecification: n nfor orthodontic work. made of hard tempered steel 19 band cutting scissors n nspecification: n nfor orthodontic work. nmade of hard tempered steel 20 band pinching pliers set n nspecification: n nset of 1 piece each ofleft & right nfor orthodontic work. made of hard tempered steel 21 band pusher n nspecification: n nfor orthodontic work. made of hard tempered steel 22 band remover anterior & posterior n nspecification: n nfor orthodontic work. made of stainless steel 23 band seater n nspecification: n nfor orthodontic work. made of hard tempered steel 24 binocular compound microscope n nspecification: n nsharp image display with excellent optical function, small space occupancy with integral stand design, low environment requirement with anti mould technology. ncomfortable operation with ergonomic design principle nviewing head: compensation free binocular head inclined at 30o interpupilary distance 55 75mm neyepiece: wide field eyepiece wf10x / 18mm with eye guard, achromatic objective 4x, 10x, 40x, 100x, nfocussing range: co axial coarse and fine adjustment range 13mm fine division 0.002mm with tension control. nnose piece: quadruple nosepiece, nstage: double layer mechanical stage 140 x 140 mm / 75 x 50 mm n.a1.25 abbe condenser with iris diaphragm and filter. nfocussing: coaxial coarse & fine adjustment system range 24mm, fine division 2mm nillumination: led light with brightness adjustable. iso 13485 or ec certificate / directive 93 / 42 / eec ) 25 block holders n nspecification: n nto be used to hold paraffin blocks and not made of plastic 26 blow torch n nspecification: n nfor casting procedure: nmade of non corrosive high fusing alloy nprovided with air flow regulator, two separate inlet line for lpg gas & oxygen 27 boley gauge n nspecification: n nmade of stainless steel for measuring tooth dimensions & others. 28 bone expansion and splitting kit n nspecification: n nthe kit consists of nosteotomes set of 5 6 of various diameters nspreaders n burs surgical for bone removal n saw disc n thumb driver & rachet nautoclavable cassette 1 piece 29 bone file howard type n nspecification: n nstraight or curved working ends nto smooth bone for better contour of alveolar ridge crosscut or straight cutting ridges double ended nmade of stainless steel 30 bone file miller type n nspecification: n ndouble ended made of martensitic stainless steel 31 bone grafting syringe n nspecification: n nfor “tamp and pack” method for placement of graft material into oral cavity. 32 bone rongeur end cutting n nspecification: n nscissor type handle, cutting edges on top edge of beaks made of martensitic stainless steel 33 bone rongeur side cutting n nspecification: n n scissor type handle, cutting edges on side and top of beaks 34 bone shear n nspecification: n nlength 6 8inches.made of stainless steel 35 boon’s gauge n nspecification: n nhigh quality stainless steel framework with minimum nmarking till 6mm 36 bracket debonding plier anterior n nspecification: n n for band removal orthodontic work. tungsten carbide tipped 37 bracket debonding plier posterior n nspecification: n nfor band removal in orthodontic work. tungsten carbide tipped 38 bracket holding tweezer n nspecification: n nfor orthodontic work. made of hard tempered steel 39 brass flask size no 6 n nspecification: n nfor acrylic denture fabrication by compression moulding, with detachable upper, body & lower member with keyways. made of brass 40 buck knife n nspecification: n nsize ¾ & 5 / 6 for use in periodontal surgery 41 bur chuck for dental lathe n nspecification: n nof different shapes for attaching abrasive stone point, stone wheel & other attachments 42 buser bone chisel n nspecification: n n6mm pointed tip made of martensitic stainless steel alloy 43 camel hair painting brush size 04 44 canine contouring plier n nspecification: n nfor orthodontic work. made of stainless steel 45 casting ring extra large n nspecification: n ncasting ring extra large nmade of steel nfor use with centrifugal casting machine nlength 4 & diameter x 4.75or more 46 casting ring large n nspecification: n nmade of steel nfor use with centrifugal casting machine . nlength3 & diameter x 3.75 47 casting ring medium n nspecification: n nmade of steel for use with centrifugal casting machine . nlength2 & diameter x 2.75 48 casting ring small n nspecification: n nmade of steel for use with centrifugal casting machine . nlength1.25 & diameter x 1.75 49 casting tong n nspecification: n nmade of stainless steel or high fusing alloy for holding casting ring 50 castrovejo needle holder n nspecification: n ncastroviejo microsurgical needle holder is a double spring instrument used for holding small, delicate needles in various microsurgical procedures. it also features a locking mechanism.made of stainless steel, autoclavable 51 castroviejo scissor n nspecification: n ncastroviejo scissor has curved blades. nultra sharp blades microscopic serrations provide a smooth cut. nspring loaded knurled handles provide the control you need to make perfectly smooth cuts in delicate materials. nstainless steel, autoclavable 52 cement mixing spatula n nspecification: n nmade of stainless steel double ended 53 ceramic sculpturing & finishing kit n nspecification: n ncomprising of high quality sable hair / synthetic filament brush size one zero, two zero and four zero and other sizes, ceramic curver, mosquito forcep, tweezer, ceramic pallete for mixing ceramic powder and other associated carving & finishing instruments. 54 chandler chisel with 5mm tip n nspecification: n nwide single bevelled blade chisel nmade of martensitic stainless steel alloy 55 chanel retractor n nspecification: n nlength 17.5 cm, made of stainless steel 56 chin retractor obwegeser type n nspecification: n nlength 15.5 cm, made of stainless steel 57 chisel curved n nspecification: n nchisel curved 20mm nmade of martensitic stainless steel 58 circular saw n nspecification: n nfor dental model cutting: with self illumination nprovided with motor driven circular saw blade and cast holding platform, electrically operated motor driven with push button type on off switches. 59 clinical micromotor brushless n nspecification: n nelectrically operated with handpiece nhandpiece autoclavable upto 135 degree celcius, handpiece speed 1000 40000rpm, speed maximum output power 1.2w, 3.4 3.5 ncm torque, with option of clockwise & anticlockwise rotation. n control box and foot control mechanism. 60 colorado needle and accessories. n nspecification: n nelectrosurgical needle is needle electrode for use in monopolar electrosurgical handpiece made of tungsten carbide. coagulation tips & cutting tipsshould work with most of the diathermy units available in the hospital , operating frequency above 3 mhz. niso / fda / ce 13485 or ec certificate ( directive 93 / 42 / eec ) 61 composite curing unit system n nspecification: n nfor indirect composite work nchamber provided with sliding tray, provided with multiple halogen or led lights light intensity not less than 900 mw / cm2output peak wavelength range 450 490 nm ( intensity maximum at 460 nm ) ncapable of curing indirect composite veneers / inlays n. curing chamber dimension : nlength 10 inches nwidth 7 inches nheight 4 inches or more nelectrically operated 220 230 volts nportable with timer 62 cooley bulldog clamp n nspecification: n nstraight 8.6cm jaw 4.7cm made of stainless steel 63 coplin staining jar vertical type 64 crane kaplan pocket marker n nspecification: n npair of two instruments –right & left 65 crane kaplan scaler n nspecification: n n double ended, round handled periodontal instrument for the removal of heavy supragingival calculus. it is a sickle type scaler, with a strong, rigid, sharply angled blade 66 crown gauge ( iwanson caliper ) n nspecification: n nfor measuring thickness of wax pattern, metal casting. nboth sided scale 0 10mm 67 crucible for small casting n nspecification: n nmade of fused silica / ceramic material, capable of withstanding high temperature for use with centrifugal casting machine 68 curing pressure pot n nspecification: n n5 liter or more capacity npressure pot temperature is preset to approximately 120°fand manually adjusts to a maximum 160°f. nsolid clad bottom provides even heat distribution. nincludes an easy to read, built in pressure gauge and quick release air valve. nthe pot has a safety device to prevent overheating, and a secure double locking lid. neasy to clean stainless steel interior. npot holder to keep pot firmly nin place. nwith lid gasket 69 cushing nerve hook n nspecification: n nused for the retraction of nerves or delicate tissue during neurosurgery. nthe instrument has a ball tip to avoid tearing. this #1 hook is angled 90 degrees with a 4mm ball tip and overall length of 7 1 / 2 inches 70 dandy type nerve hook n nspecification: n n length 16 20cm ntip 4 5mm, deep working tip blunt ended made of stainless steel 71 dappen dish made of glass 72 de la rosa wire contouring plier n nspecification: n nfor orthodontic work. made of stainless steel 73 deans scissors: n nspecification: n nscissors with 1 serrated angular blade used for trimming tissue or cutting sutures. 74 debackey’s forceps n nspecification: n n length 26 cm, tip width 1.5 mm made of stainless steel 75 debackey’s vascular forcep 6” n nspecification: n nmade of stainless steel, autoclavable 76 debakey bulldog clamp 8.5cm n nspecification: n nwith serr.jaws, straight made of stainless steel 77 dental dewaxing unit n nspecification: n nwith digital control for water temperature regulation. construction: stainless steel ntank sizes ( 300 x 200 x 350 mm ) approximately nwater filling: manual heater: 2000 watts. with drain valve 78 dental excavator discoid type n nspecification: n nmade of stainless steel double ended niso 13397 4:1997 79 dental lathe motor n nspecification: n nac, hp 1, universal, rpm 2800, equipped with double b.b, single speed, rating continuous with 3 chucks ( buffer, stone & bur chuck ) , three imported b.b. flexible metal cable arm and its attachment. 80 dental muffle furnace n nspecification: n n1150c degree celsius, working temperature 900 degree celsius, with er & digital display nmuffle size 175x175x225mm. 4.0 k.w. capacity 81 dental phantom head unit n nspecification: n nmanikin head fixed with a table, with mounted upper & lower jaw containing screw mounted teeth having 90° swiveling function of head unit, provided with control box for micromotor, foot control & micromotor with contra angle handpiece, should have mounted light unit with illumination power not less than 7000 lux. 82 dental plaster dispenser n nspecification: n nbody made of stainless 304 grade, fitted with digital electronic timer, capacity 5 kg or more. will dispense premeasured dose of plaster at touch of a button. 83 dental steam cleaner n nspecification: n npower 1500w or more, 220v, frequency 50 / 60hz. working pressure: 4 5 bar. capacity 5 10litre. with thermostat controller.device with both steam gun & button / lever controlled steaming attachment with steam regulator. stainless steel non rusting inner tank body. 84 dental surveyor tool kit n nspecification: n ntools nanalyzing rod multiple undercut gauges n carbon marker sheath n wax trimmer 85 dental surveyor ney’s type n nspecification: n ndental surveyor ney’s type nhorizontal platform n• adjustable spindle for the vertical indicator n• survey table that can be locked at any angle. nwith tools analyzing rod undercut gauges n carbon marker sheath n wax trimmer etc nprovision for holding micromotor handpiece nstandard packaging / physical verification of sample may be made 86 dental tweezer n nspecification: n nwith horizontal serrations at tip, diamond knurling on the outside for good grip, stainless steel alloy 87 dental vacuum former machine n nspecification: n nelectrically operated, with inbuilt vacuum motor suction unit, heating element with on off switches & adjustable clamping plate. nspecifications: nvoltage : 230v / 50 60hz npower : 600w 230v nheater : 400w 230v ndimension : l 23 25 cm, w 17 20 cm 88 dg 16 endodontic explorer 89 diamond glass marker n nspecification: n nmounted in aluminum pencil 5 inches ( 12.7cm ) 90 die cutting machine n nspecification: n nelectrically operated with diamond disc. nwith adjustable model holder nself illuminated chamber 91 dingmans retractor n nspecification: n nwith three blades made of stainless steel 92 distal end bender n nspecification: n nfor orthodontic work. made of stainless steel ) 93 distal end cutter n nspecification: n ntungsten carbide tipped ncutter for all types of wire up to a maximum of .021” x .025” ( .53 mm x .64 mm ) 94 distal end cutter n nspecification: n nfor orthodontic work. made of stainless steel 95 dontrix gauge n nspecification: n nspring balance type, minimum measurement till 500 ngms to precisely calibrate orthodontic force there are two units of measurement ounce and gram. measuring range: 0 450g / 0 16 oz. to measure tension and compression force 96 double wax heater pot n nspecification: n nwith thermostat controlled temperature regulator electrically operated 97 dry model trimmer n nspecification: n n with attached suction unit 98 duplicating flask n nspecification: n n a. programmable brushless agitator motor ntemperature controls for precision warm up and cool down phases nintelligent heating strategy and provision for effective disposal of gel and prevention of nozzle blockage nmaintainance of consistent gel quality nvoltage: 200230v, 50 / 60hz, nb. pressure compaction unit for duplicating silicone materials nautomatic mixing and metering unit for two component silicone material nduplicating flask: n ( a ) individual aluminium duplicating flask with aluminium top and rubber base and 2 base formers ( 2 sizes ) n ( b ) duplicating flask with stabilizing insert and three replaceable palatal formers of different sizes 99 electrically operated wax carver n nspecification: n nelectrically operated electrical wax curver with thermostat controller. with two detachable carving tools 100 electro polisher n nspecification: n nautomatic digital electro polisher, auto / manual modes, nwith trimmers, electrolyte flow regulation n38 mm disc for psa paper & cloths nsupply 230 v. ac ncurrent – 2.5 amp., voltage – 80v, supply – 230 v.a.c.polishing probes – unique pen type system with recirculation of electrolyte, pump 25 watts reservoir ( 0.5 ltr ) 101 endo activator n nspecification: n nsystem kit that includes handpiece / driver nbox of small, medium & large activator tips. nbox of 100 protective barriers. safe & vigorous energetising intracanal irrigant, capable of debriding & disinfecting root canal system 102 endodontic microsurgical equipment n nspecification: n ncomprising of na. ultrasonic piezoelectric scaler with inbuilt irrigation , led & water tank nb. ultrasonic endodontic retro surgical tips ( for anterior teeth upper & lower and posterior teeth of upper and lower arch ) nc. ultrasonic passive irrigation, nd. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal 103 endomotor with torque control nhand piece. n nspecification: n ncontinuous & / or reciprocating motions for root canal shaping, hand piece with integrated on off switch, auto reverse mode, speed 250 1200 rpm. n torque range 0.6 4 ncm, n multiple adjustable programs nstandard packaging / physical verification of sample may be made 104 endovac irrigation system n nspecification: n n multiple port adapters, hand piece set, extra evacuation system, cannulas, delivery tips & syringes. 105 excavator oval type 106 excavator spoon type n nspecification: n nexcavator double ended spoon type 107 extraoral gothic arch tracer n nspecification: n njaw movement recording and centric relation npositioning, one stylus and one tracing plate nattachments to the jaw movement recording bases noutside the mouth nstandard packaging / physical verification of sample may be made 108 farabeufs periosteal elevator n nspecification: n nof different sizes length 6 8inch, width 8 12mm, made of stainless steel. 109 fergusons mouthgag n nspecification: n nmade of stainless steel n 110 fiber optic light n nspecification: n nfiber optic based lighting unit consisting of fiber optic cable, led based portable light with controller unit. with rechargeable battery niso 13485 or ec certificate ( directive 93 / 42 / eec ) 111 flask clamp for brass flask n nspecification: n nmade of steel with clamp compatible with brass flask of size no 6 112 frahm amalgam curver 113 furcation curettes quetin n nspecification: n nbuccal lingual 0.9mm 1pc quetin buccal limgual 1.3mm 1pc nquetin mesial distal 0.9mm 1 pc quetin mesial distal 1.3mm 1pc nconform to iso 13485:2003 / en iso 13485:2012 114 gardner chisel with 3mm tip n nspecification: n nsingle bevel chisel nmade of martensitic stainless steel alloy 115 gates glidden drill set n nspecification: n nstainless steel, drill compatible with latch type handpiece for use in bulk removal of the tooth structure nunit pack containing six different sizes each drill having 28 32 mm length. 116 gillie’s skin hook doubleprong n nspecification: n nmade of stainless steel n 117 gillie’s skin hook single prong n nspecification: n nmade of stainless steel n 118 glass bead sterilizer n nspecification: n nelectrically temperature regulated to heat contained glass beads with on off switch. nsmall rectangular base for keeping at chairside nprovided with lid. n it should reach operating temperature of approximately 240 c to 270 c in 15 20 minutes time. nsterilization is on contact with glass beads nunit can be left in the “on” position all day and is safe for use in laminar flow cabinets. 119 glass slab 8mm thick n nspecification: n ntransparent rectangular glass slab thickness 8mm, length 6” x 4” inch 120 glass slab big n nspecification: n ntransparent square glass slab thickness 4mm, each side of 6 inch 121 glass slab small n nspecification: n ntransparent square glass slab thickness 4mm, each side of 3.5 inch 122 goldmanfox periodontal probe n nspecification: n ndouble ended probe, markings at 1, 2, 3, 5, 7, 8, 9& 10mm.high quality stainless steel with satin finish, antimagnetic rust resistant, acid resistant 123 gracey curette set n nspecification: n nof 9 size ½, ¾, 5 / 6, 7 / 8, 9 / 10, 11 / 12, 13 / 14, 15 / 16, 17 / 18.made of hard tempered steel ndouble ended nhandle 10.2 10.8cm nshank 3.1 3.6cm nlength 6.8 7.4mm noffset blade beveled at 60 70 degree to the shank n1.triple tempered steel n2.satin steel handle n3.corrosion resistant n4.rust resistant n5.stain resistant n6.can be sharpened by traditional sharpening stones nconform to iso 13485:2003 / en iso 13485:2012 iso 13485 or ec certificate ( directive 93 / 42 / eec ) ce & fda aprroved 124 guarded nasal chisel set of right &left n nspecification: n nsize : 4, 5, 6, 8mm right & left in pair made of stainless steel 125 half round plier n nspecification: n nfor orthodontic work. made of hard tempered steel 126 hand scaler set of 5 piece n nspecification: n nset containing 1 piece each of: sickle, push, universal, broad right & left . 127 hard wire cutter n nspecification: n nhard wire cutter made of tungsten carbide tipped 128 heavy duty lathe with suction unit n nspecification: n nelectrically operatedheavy duty motor unit having power not less than – 0.5hp nhigh speed r.p.m. 3000 rpm narrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with nbuilt in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. ntable mountable heavy base plate for vibration free operation nbuilt – in lighting for high visibility 129 heavy wire cutter n nspecification: n nwire cutter tungsten carbide tipped n 130 hinge articulator n nspecification: n nrust free construction npermit opening & closing in hinge like motion. support upper & lower cast. n upper member adjustable with locking nut. 131 hook crimping plier n nspecification: n nfor orthodontic work. made of stainless steel 132 hot plate with wooden handle 133 howarth’s periosteal elevator n nspecification: n ndouble ended: one end flat, broad sharp edge, other end rugine ended made of stainless steel 134 howe’s pliers anterior n nspecification: n nwith serrations, useful for placement and removal of archwires, pins and other auxiliares nmade of stainless steel 135 howe’s pliers posterior n nspecification: n npliers with serrations, useful for placement and removal of archwires, pins and other auxiliares 136 humby’s knife holder n nspecification: n nmade of stainless steel n 137 hydraulic press n nspecification: n nthe closed circuit hydraulic press should work with a pressure up to 7000 kg of thrust. n it can contain up to three flasks at a time. nthe structural elements in chromium plated steel. n provided with dial. 138 hydro solder n nspecification: n nmains voltage: 1 x 230 v, mains frequency: 50 x 60 hz, mains fuse: 1 x 10. a nmax.gas production: 6 liter nmax. nozzle size: 0.07mm n dimensions w x h x d x ( mm ) : 330 x 230 x 310 mm nweight: 22 kg ncapacity: 110lt, with accessories 139 implant microsurveyor n nspecification: n nwith compass surveying system, portable hand held surveyor 140 implant retractor n nspecification: n nmade of stainless steel. autoclavable 141 incubator n nspecification: n nrobust construction nflawless finish nlong functional life ninner chamber size 14 x 14 x 14’’ with two shelves nwith thermostat control & digital display iso / fda / ce or ec certificate 142 inlay wax curver double ended 143 instrument sharpening kit with arkansas stone n nspecification: n n flat arkansas stone with conical shape nplastic test stick ( 5 ) nstone oil nmagnifying lens& other accessories 144 intra oral camera with video monitor n nspecification: n na ) camera: neasy to use, narrow head, comfortable for patient intra oral camera with provision of variable lens adjustment that can be attached to dental chair unit nvideo compatible so that images can be displayed on a computer workstation / lcd monitor nstill image resolution: 1024 ( h ) x 768 ( v ) or more nvideo resolution: 640 ( h ) x 480 ( v ) or more nfocus range: 1 mm 25 mm nlens surrounded by led lamp ninput: 220v 50 60hz noutput: 5v, 2a 145 intraoral camera with fluorescent technology n nspecification: n nintra oral camera with caries detection and periogingival inflammation detection facility based on flurescent technology 146 intraoral sand blaster n ( microetcher ) n nspecification: n nlong tubing with compatible adapter for the airotor handpiece point nof the dental chair, fully autoclavable, 50 microns naluminium oxide particle size, 360 degree adjustable nozzle. 147 intraoralgothic arch tracer n nspecification: n njaw movement recording and centric relation npositioning, one stylus and one tracing plate nattachments to the jaw movement recording bases ninside the mouth n 148 kilner’s cheek retractor n nspecification: n nmade of stainless steel n 149 kirkland gingivectomy knife n nspecification: n nfor use in periodontal surgery n 150 kocher’s forceps n14cm hemostatic forcep. n nspecification: n n it is specifically designed to catch the bleeder that are deep within tissue hence it is ideally used on tough structures made of stainless steel 151 laboratory micromotor with brushless motor n nspecification: n ncompact and portable size, continuous variable speed control , r.p.m 1000 40000, on / off foot switchone touch change of the driving direction for efficient operation with brushless motor with handpiece 152 laboratory micromotor with carbon brush motor n nspecification: n ncompact and portable size, continuous variable speed control , r.p.m 1000 40000, on / off foot switchone touch change of the driving direction for efficient operation with carbon brush motor with handpiece 153 langenback’s retractor n nspecification: n nmade of stainless steel n 154 laser guided pin drilling system with pins n nspecification: n nelectrically operated 110v / 240v, laser guided pinsetter, pin drilling for easy die pin attachment. nlaser light technology with carbide bur drill with high speed motor. nto accurately drill parallel holes into the underside of the model die pins of various sizes ( 1000 pieces total ) made with non corrosive alloys for use with pindex system of die pins. 155 lead apron n nspecification: n nadult size, 0.5 mm thick lead covered with cotton on nboth sides, overstraps, buckles & hand gloves ( size 6 nto 7.5 ) with 0.5 mm thickness lead 156 lecron wax n nspecification: n ncurver made of steel n 157 leuckhart pieces n nspecification: n ntwo l shaped metallic stands for preparing paraffin wax block 158 light cure unit n nspecification: n n led based. light modes fast, ramped & pulsed ndisplay for mode & timer nselection nchordless with rechargeable lithium battery nlight intensity not less than 1200 mw / cm2output peak wavelength range 450 490 nm ( intensity maximum at 460 nm ) nwith inbuilt timer, on off switch 159 lingual arch plier n nspecification: n nfor orthodontic work. made of stainless steel 160 loop forming plier n nspecification: n nfor orthodontic work. nmade of hard tempered steel 161 loop forming plier n nspecification: n nfor orthodontic work. made of stainless steel 162 lower molar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint set of one piece right & one piece lower molar forcep 163 lower premolar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 164 lower roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip 165 lower universal forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint set of one piece right & one piece lower molar forcep 166 magnification loupes 3.5x n nspecification: n nergonomically designed binocular loupe that can be worn over spectacle frame capable of 3.5x magnification at 420mm with 3watt led rechargeable light 167 magnification loupes 4.5x n nspecification: n nergonomically designed binocular loupe that can be worn over spectacle frame capable of n4.5x magnification at 420mm with 3watt led rechargeable light n 168 magnifying work lamp n nspecification: n nwith flexible & adjustable stand and base. inbuilt led based optical illumination system. nglass lens diameter 7 inches or more, magnification power upto 4 x 169 manual crown remover n nspecification: n n with adjustable spring with crown remover tip ¬ 2 single crown remover contrangled tip ¬ 3 open¬end adjustment wrench 170 manual press n nspecification: n nwith base and cross bar made with high strength steel. nthe structural elements made with chromium plated steel. ncapable of pressing upto 1 to 3 flasks at a time. nbase should have holes for attachment to bench 171 marquis colour coded probe n nspecification: n nfor periodontal surgery made of stainless steel colour coded at 3 6 & 9 12 mm 172 mathieu plier n nspecification: n nstraight & curved for orthodontic work nused for ligature typing and placing of elastics 173 mbt gauge n nspecification: n nfor .022” slot nfor orthodontic work. made of stainless steel 174 metal impression tray non perforated n nspecification: n nmade of non corrosive alloy nfor edentulous patient set of upper & lower, size 0, 1, 2, 3, 4. n ( price being same to be supplied as per requirement of user ) 175 metal impression tray perforated n nspecification: n nfor dentulous patient nmade of non corrosive alloy nset of upper & lower, size 0, 1, 2, 3, 4. n ( price being same to be supplied as per requirement of user ) 176 metal suction tip n nspecification: n na ) 3mm diameter 10 pc nb ) 5mm diameter 10 pc nmade of stainless steel 177 micro oscillating saw n nspecification: n ncapable of easily cutting channels and bone blocks nmaximum 12, 000 oscillations per minute. compact design for easy access . ntwo shaft lengths & 4 blade sizes for optimum access. nincludes external irrigation port for effective bone cooling nuniversal e type coupling that fits implant motor unit 178 microhead air rotor handpiece n nspecification: n nsuitable for use in child patient, head size 8.5 x 19.4 mm, provided with water spray, body made with ceramics autoclavable, rotational speed 3, 00, 000 to 450, 00, 00 rpm, provided with a bur changer & wrench. nphysical verification required 179 micropipettes n nspecification: n nfeature built in tip ejectors and autoclavable tip cones. should work on a click stop digital system, are easy to calibrate and maintain, and easy to disassemble for autoclaving. manufactured as per iso 9001:2008. each pipette should be individually calibrated according to iso 8655 standards.calibration certificate must be provided with each pipette. accuracy and precision values should be those laid down in the iso 8655 standards.built in, streamlined tip ejector facilitates easy tip ejection and access to narrow necked bottles and tubes. variable volume pipette: 50 200 μl. increments [ μl ] : 1 9 volume [ μl ] : 50 to 200. accuracy ( ± ) %: 0.6 to 1 11 precision ( ± ) %: 2 to 0.3 12 it should be ce mark 180 microvascular instrument kit n nspecification: n nkit comprises of n1.micro scissors n2.micro needle holder n3.jwellers forceps n4.vessel dilators n5.liga clips ( no.100.no.200 ) n6.ligaclip applicators n7.vessel clamp ( 2a, 2v, 3a, 3v ) n8. vessel clamp applicator n9. hand held colour doppler unit n10.pneumatic tourniquet nspecification to be quoted by the bidder / manufacturer nmicro scissors ni ) adventitia scissors flat handle , 8mm wide, straight length of 15cms, blades 19mm – 5 pcs nii ) dissecting scissors – flat handle, 8mm wide , curved, length of 15cms, blades 19mm – 5 pcs niii ) adventitia scissors round handle, 8mm diameter of tip, straight, length 15cms, blades 12mm – 5 pcs niv ) dissecting scissors – round handle, 8mm diameter of tip, curved, length 15 cms, blades 12mm – 5 pcs nmicro needle holder: ni ) flat handle , 8mm wide, curved, 14 cms length – 6 pcs nii ) round handle, 8mm, curved, 15 cms length – 6 pcs njewellers forceps ni ) flat handle , 9mm wide, straight, 13.5 cms length – 6 pcs nii ) flat handle , 9mm wide, angulated 45 degrees, 13.5 cms length – 6 pcs niii ) round handle , 8mm wide, straight, plateau, 15 cms length – 6 pcs nvessel dilators: ni ) flat handle , 9mm wide, angulated 10 degrees, nlength 11cms – 6pcs nliga clips – made of stainless steel, autoclavable. nno.100 – 150 sets ( each set containing 6 liga clips ) nno.200 150 sets ( each set containing 6 liga clips ) nno.400 – 100 sets ( each set containing 6 liga clips ) nligaclip applicator: ngrooves on inside jaw surfaces of applier which helps in increasing of jaw clip security. nangled jaws to improve visibility beyond structures nmechanical stop. nmade of stainless steel and autoclavable. 181 mini pin & ligature wire cutter n nspecification: n ntungsten carbide tipped ncuts soft wire pins and ligature wire up to .012” ( .30 mm ) 182 miscellaneous hi n nspecification: n n139 plier for orthodontic work. made of stainless steel 183 miscellaneous hi 184 model trimmer with carborundum disc n nspecification: n nmotor rpm 2800 heavy duty, equipped with two ball bearing single speed, rating continuous with buffer and 10 carborundum disc , with heavy base that can be clamped and installed on underlying table, with water inlet and out flow water system. 185 model trimmer with diamond disc n nspecification: n n1 / 2hp, rpm 2800, heavy duty equipped with two ball bearings, single speed, rating continuous with buffer and one 10 diamond disc rough or fine without suction.1 piece spare diamond disc to be provided 186 model trimmer with double disc n nspecification: n none diamond & one carborundum disc n rpm 2800 double motors horsepower 1 / 2 or more each, heavy duty, equipped with two ball bearings each motor, single speed, rating continuous with fixed one10 diamond disc fine, one carborundum coarse cutting wheel, base inlet, with outflow water system. 187 molts elevator n nspecification: n nlength 7”double ended with one round, blunted end and one pointed end made of stainless steel 188 mouth prop n nspecification: n nautoclavable made of stainless steel with rubber pads for intra oral use over occlusal surfaces during surgery. the rubber pads are of 4 sizes attached by a stainless steel chain. 189 naber’s probe n nspecification: n nfor use in periodontal surgery double ended furcation probe nconform to iso 13485:2003 / en iso 13485:2012 190 omega loop forming plier n nspecification: n nfor orthodontic work. made of stainless steel 191 orban gingivectomy knife n nspecification: n nfor use in periodontal surgery n 192 oschenbein chisel curved n nspecification: n nsize no. 1 and no. 2 ochsenbein chisels periodontal chisels. they havethree cutting edges, a flat edge on the tip and a curvededge on each side of the tip. 193 oschenbein chisel straight n nspecification: n n17.5 cm x 4 mm nsize no. 1 and no. 2 ochsenbein chisels periodontal chisels. they havethree cutting edges, a flat edge on the tip and a curvededge on each side of the tip. 194 osteotome 20mm n nspecification: n nmade of stainless steel n 195 paeso rimmer drill set n nspecification: n nstainless steel, drill compatible with latch type handpiece for use in bulk removal of the tooth structure nunit pack containing six different sizes each drill having 28 32 mm length. 196 palatal trimmer n nspecification: n nprovided with1 fast cutting trimmer, electrically operated , rpm 2600 or more nbody made with 304 grade stainless steel, or non rusting alloy. dull finished work surface, dust collection with adapter hose, provided with1 fast cutting trimmer 197 paquette blade handle 198 paraffin wax bath ( thermostatically controlled ) n nspecification: n nconstruction – double walled effectively insulated.wax tank of 20 gauge ss sheet. fitted with laminated wooden rim and anodized alumininium cover mounted on 5 cm diameter. nheater two 1 kw each special wax heater. nheat control thermostat to control temperature fron 30 degree c to 110 degree c nfinish externally finished in oven baked naccessories power plug, 1 brush for wax application and aluminium sheet mesh for heater. 199 pediatric extraction lower incisors & canine forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 200 pediatric extraction lower molar forcep n nspecification: n nfor children nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, n 4.5 inches of length 201 pediatric extraction lower premolar forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 202 pediatric extraction universal forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 203 pediatric extraction upper incisor & canine forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 204 pediatric extraction upper molar forcep left n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 205 pediatric extraction upper molar forcep right & left n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 206 pediatric lower roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 207 pediatric upper roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 208 piezo surgical kit n nspecification: n n device with intermittent operation, 60 sec on then 30 sec off with irrigation, & 30 sec on 120 sec off without irrigation, power supply 240v, 50 / 60 hz, maximum power absorbed 120va. surgical tip capable of modulating from 10 to 30 or more. 29khz or more. power adjustable from 2.8 to 16w. tip vibration in range of 60 200μm.motor with tips & other accessories n ( european ce / fda ( usa ) approved ) 209 pikling kit n nspecification: n nelectrically heated and thermostatically controlled pickling unit for acid based pickling agents with low power consumption for pickling of precious metals. swivel sieve and housing made of shock proof and acid resistant polypropylene material 210 pin & ligature wire cutter n nspecification: n ntungsten carbide tipped ncuts soft wire pins and ligature wire up to .015” ( .38 mm ) 211 plaster knife n nspecification: n nwith working length not less than 2 .5inches 212 plaster spatula n nspecification: n nround ended steel spatula having width of 1.25 inch & length 5 6 inches, with plastic or wooden handle 213 plastic filling instrument nward type 214 pneumatic crown remover n nspecification: n npneumatic, autoclavable tips, basic kit includes easy pneumatic crown and bridge remover bridge remover tip ¬ 1 single crown remover tip ¬ 2 single crown remover contrangled tip ¬ 3 open ¬ended adjustment wrench rubber gasket flexi¬wire set 215 pneumatic deflasking unit n nspecification: n n operates on air pressure. nwith handheld chisel provided with detachable tips n provided with variable powercontrol with air inlet and tubing length not less than 1.5 meter. nworking pressure 1 6 bar 216 portable transcutaneous electrical nerve stimulation ( tens ) n nspecification: n nunit for pain management with replacement electrodes. the machine should have burst, continuous and modulation pulse modes. dual, isolated between channels with a pulse intensity of 0 80ma peak into 500ohm load. pulse rate of 2 120hz adjustable. pulse width 40 260 microseconds, adjustable. maximum voltage: 110v. maximum charge: 21microcoulombs per pulse 217 pressure moulding machine n nspecification: n nthe unique thermally controlled heater reaches working temperature in few minutes. npower: 230 v, 850 w nworking pressure: 0, 5 – 6, 0 bar nmeasurements ( w x h x l ) : 450 x 230 x 260 mm 218 pulp tester digital n nspecification: n npreset stimulus speed mode, battery 9v, auto off after 3 min, with autoclavable tips, one touch operation, with digital read out of display 219 punch biopsy forceps n nspecification: n nmade of stainless steel n 220 rib raspatory right & left n nspecification: n nmade of stainless steel n 221 rib shear ( doyan ) n nspecification: n nmade of stainless steel n 222 ribbon arch plier n nspecification: n nfor orthodontic work. made of stainless steel 223 rme bender n nspecification: n nfor orthodontic work. made of stainless steel 224 robinson black bristle brush n nspecification: n nhaving diameter of not more than 2.5 inch. 225 root canal explorer 226 rowe zygomatic elevator n nspecification: n nmade of stainless steel n 227 rubber bowl n nspecification: n nsize large n13 cm in height made with flexible synthetic rubber material 228 rubber dam kit n nspecification: n nrubber dam clamp forceps nrubber dam punch nrubber dam frame adult nuniversal rubber dam template nfdi rubber dam nprovided with different clamp designs such as molar clamps, bicuspid clamps winged, labial clamps winged nit contains: n plastic dental dam frame 6 / 5 n wedjets stabilizing cord pack ( s ) n hygenic template 6 / 5 n punch n forcep n rubber dam sheets 6x6 ( 36 ) / pedo 5x5 ( 52 ) n set of 9 clamps adult / set of 6 pedo 229 sand blaster unit n nspecification: n nself illuminated chamber. unit with ventilation slits with rubber gloves, pressure regulator, air filter , provided with glass pane. flow of blasting material from 1 to 6 bar. with wear resistant nozzle tip attached with wear & tear resistant hoses & nozzles. with filter. micro & macro mode 230 sanders knife nsize 1 / 2 231 schluger bone file for use in periodontal surgery 232 self adjusting endodontic file system ( saf system ) n nspecification: n ndigitally controlled endodontic micromotor with peristaltic pump. n self adjusting root canal files, rotary motion with speed and torque control, nreciprocating motion with reverse / forward angular movement 233 self retaining retractor weit laner type n nspecification: n n made of stainless steel n 234 semi adjustable articulator with accessories n nspecification: n nwide view arcon articulator with spring¬ bow, ear¬piece, face bow, orbital indicator, bite fork & other accessories nstandard packaging / physical verification of sample may be made 235 separator placement pliers n nspecification: n nfor orthodontic work. nmade of hard tempered steel 236 sinus lifting instrument kit n nspecification: n nfor lateral & crestal approach n with s reamer / lateral reamers ninitial drill / crestal drills n bone inserter nbone spreader n bone carrier n bone condenser ndepth gauge n chisels of different width n sinus curettes of various designs n bone rongeur forceps nmallet nirrigation syringe & tips n& other instruments nautoclavable cassette 1 piece 237 slide storing cabinet n nspecification: n ncabinet for 1050 slides consisting of 6 drawers each for 175 slides, arranged in single rowframework made of 15mm plywood with top and sides covered with sunmica laminated sheet. 238 slide warming table n nspecification: n ntop surface made of stainless steel ( ss 304 grade ) nthe surface temperature is controlled from ambient to 70°c nsupplied complete with pilot lamp, cord and plug nto work on 220 / 230 volts a.c. supply 239 spirit lamp n nspecification: n nmade of stainless steel nof 100 ml capacity with wick & detachable cap stainless steel body 240 spot welder with soldering attachment n nspecification: n n• electrically operated n• voltage110 240 volts n• applications / indication spot welding n• power settings2, 000 amperes n• heat settings2 n• electrode / tip type hand electrode n• welding positions adjustable 241 steel mallet n nspecification: n nfor use in oral surgical work made of stainless steel length 7.5”, nhead diameter 20 22mm 242 steel slide racks for staining n nspecification: n n the 5 slide gripper can accommodate 5 microscope slides in one staining procedure.it fits most coplin and round open staining jars nit should be made of a special material which is resistant to all chemicals and solvents which are used in staining nit withstands drying temperatures up to 80°c 243 step plier n nspecification: n nfor orthodontic work. made of hard tempered steel 244 surgical elevators coopland’s pattern n nspecification: n nmade of hard stainless steel n 245 surgical elevators cryer’s pattern n nspecification: n nmade of hard stainless steel nlength 145mm, neck diameter 3.6mm, working tip length 9mm for right & left nset of 2 units cryer’s right, left 246 surveyor mounted miling machine n nspecification: n nuniversal precision milling unit. areas of application; wax milling and scraping ; milling, fine grinding, drilling and smoothing of metal with the help of the modeling spindle, it can be used as a surveying instrument and for mounting auxiliary parts. magnetic locking device for model table. drilling depth stop and connection facilities for additional handpiece for finishing. advantages: universal design for measuring, blocking and routing ( router head accept spindles, drawing tools and measuring tools ) . easily movable double articulating arm free from play. routing spindle with quick coupling. controllable, heatable wax knife nrpm can be infinitely controlled from 3000 to 35000 rpm. left / right rotation. route head with micrometer screw for exact vertical bores. good illumination due to integrated led light iso 13485 or ce certificate 247 three prong plier n nspecification: n nfor orthodontic work. made of stainless steel 248 tissue biopsy kit n nspecification: n n1.small and short scalpel blades ( no. 15, 11, 12 or even 5 ) – n 2. mosquito forceps – 2 pc curved & 2 pc straight n3. gauze container made of stainless steel size small 1pc n 4. alley’s tissue forcep 2pc n5. punch biopsy set one piece of three different diameters ( circular blade size 3 mm, 5mm & 7 mm ) in each kit n6. mc indoe’s dissecting scissor1pc n7. bone scoop small1pc n8. bone curette tip diameter 3 mm 1pc n9. sklar tungsten carbide bozeman 10.needle holder 8 tungsten carbide tipped 1 pc with catch, n11. wards needle holder 1pc n12. toothed dissecting forcep 1pc n13. non toothed dissecting forcep 1pc 249 tissue capsules / tissue embedding cassettes n nspecification: n nmade of acetyl polymer;cassettes should keep specimen safely submerged in liquid, efficient flow through slots, snap latch and hinge lock design prevent early separation of base and lid and allows for one hand operation. large labeling area on two sides of cassette. anterior writing area is at 35° angle. npore size: 1mm square pores noutside dimensions: 28.5 x 41 x 6.7mm ( 1.12 x 1.61 x 0.26 ) ninside dimensions: 26 x 30 x 5mm ( 1.02 x 1.18 x 0.2 ) 250 tissue floatation water bath n nspecification: n n ( thermostatically controlled ) inner tank ( single piece ) made of black anodized aluminum. housing made of powder coated aluminum. front panel consist of temperature regulator knob, mains switch and pilot lamp. inside black and outer surface finished in powder paint, with wide enough rim for drying the wet slides. nbath size ( inner ) 225mm*70mm ntemperature controlled by capillary tube thermostat ntemperature range n+5 degree c to 70 degree c 251 torch, alcohol, dental n nspecification: n nwick volume capacity 90ml or more, with adjustable needle point flame, body metal or plastic 252 torquing pliers male n nspecification: n nfor orthodontic work. made of stainless steel 253 torquing pliers male n nspecification: n nfor orthodontic work. made of stainless steel 254 tourniquet arm n nspecification: n nhaving pressure regulator, tubing and connectors with not less than7 cm inflatable cuff 255 tourniquet leg n nspecification: n nhaving pressure regulator, tubing and connectors with wide 14 cm inflatable cuff 256 towel clips ( clamps ) nbackhause type n nspecification: n nto secure surgical drapes and to secure plastic and rubber tubing to drapes features: sharp prong tips 31 / 2 inchand 51 / 4 inch additional use: remove metal temporary crowns made of stainless steel 257 towel cross section clip n nspecification: n nmade of stainless steel used to fix drapes to tissue with minimal trauma during surgical operations 258 tracing table n nspecification: n nbox portable with opaque screen nlight box with led nelectrically operated with ajustbale illumination. box dimension 14” x 16” or more 259 transparency scanner n nspecification: n ndual lens system, minimum 6, 400 dpi optical nresolution, 4.0 dmax for smooth gradation and fine nshadow detection, antireflective noptical coating and nhigh reflection mirror, digital ice technology, 8” x 10” ntransparency unit built into lead 260 trephine bur set n nspecification: n n of 3. dia 2, 3, 4mm nfor harvesting bone cores for use in periodontal surgery iso 13485 or ec certificate ( directive 93 / 42 / eec ) 261 turret n nspecification: n nzero torque ( blue ) nfor orthodontic work 262 tweed plier n nspecification: n nfor orthodontic work. made of stainless steel 263 typhodont articulator n nspecification: n narticulated model with soft pink ( not transparent ) acrylic or plastic gingiva material. included:28 anatomically shaped screwable typhodont ivorine teeth 264 ultrasonic cleaner n nspecification: n n 220v, 100 200watt & above, 5 liter capacity, with stainless steel body &cover. 265 ultrasonic dental scaler n nspecification: n nelectrically operated 220 / 240v 50 / 60hz ac with control box, multi frequency handpiece with scaling tips, foot control, water connector, tube & other accessories. capable of upto 20khz ultrasonic vibrations / second or more niso 18397:2016 / iso / fda / ce 13485 or ec certificate 266 unc 15 periodontal probe plastic n nspecification: n n probe with markings at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15colour coded at 5, 10 & 15mm, thin shanked probe 267 unc 15 periodontal probe: titanium n nspecification: n nprobe with markings at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15colour coded at 5, 10 & 15mm, thin shanked probe nconform to iso 13485:2003 / en iso 13485:2012 iso 13485 or ec certificate ( directive 93 / 42 / eec ) 268 universal columbia curette n nspecification: n ncommon properties: n1.triple tempered steel n2.satin steel handle n3.corrosion resistant n4.rust resistant n5.stain resistant n6.can be sharpened by traditional sharpening stones n7.properly designed & balanced handles to reduce chances of “carpal tunnel syndrome” na ) in different sizes nhandle 10 11cm nshank 2.7 3.2cm nblade length 5.8 6.5mm, width 1.3 1.6mm, 90 degree offset angle nsemicircular cross section with convex base nb ) in sizes of sc4r / 4l6 nhandle 10 11cmshank 2.9 3.4 cm nblade length 5.8 6.5mm, width 1.3 1.6mm, n90 degree offset angle nsemicircular cross section with convex base. 269 university of michigan o probe n nspecification: n nfor use in periodontal surgery nsingle ended probe with markings at 3 6 8mm 270 upper canine extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 271 upper incisor extraction forcep english pattern n nspecification: n nforcep made of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 272 upper molar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint nset of one piece right & one piece left upper molar forcep 273 upper premolar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 274 upper roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip 275 upper universal forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip 276 uv steriliser n nspecification: n ndimensions of cabinet: 22 x 12 x 8” nfront door with uv protected glass window & magnetic door seal nprovided with multiple tray racks not less than four nelectrically operated nprovided with uv light source 277 vacuum investment unit n nspecification: n ncapable of mixing unit amount of investment material under vacuum through a motor 278 vacuum mixing machine n nspecification: n n1. vacuum mixing machine nfor mixing investment material n2. electrically operated motor 1500 watts or more n3. compact n4. automatic regulation of the vacuum n5. the mixing motor remains clean and is easily serviced due to a supporting filter and a fine filter in conjunction with the maintenance free vacuum pump n6. direct connection between mixing bowl and vacuum pump – no disturbing exterior hose n7. mechanical coupling tolock the mixing bowl in position n8. a mixing bowls ( 500 g ) niso 13485 or ce certificate n 279 vibrator n nspecification: n n• electrically operated size 4.5 x 8 x 6.5 inches or moreplatform shaperectangular, type heavy duty n• constructionenamel painted body with rubber plate above body, speed: 3 speed vibration controller n• platform shaperectangular 280 warwick james elevators n nspecification: n nmade of hard stainless steel nset of 3 units right, left & straight tips 281 wax block storing cabinet n nspecification: n ncabinet made out of duro board, externally clad in laminated sheet. dust proof door is lockable. provided with smoothly sliding drawers with sixteen compartments each of size 4x4x2 and have puller knobs. each compartment can store blocks in two rows. 282 wax burnout furnace n nspecification: n nmaximum temp 1200c working temp 1150c with digital display cum temperature controller with safety alarm nmuffle size : 175x175x225mm n 4.0k.w 283 wax curver: pkt type n nspecification: n nset of 5 instruments n 284 wax knife n nspecification: n nmade of stainless steel nwith one end bearing knife pointed & other thick, flat with curved end 285 wax spatula n nspecification: n nmade of stainless steel nwith one end pointed & other end curved 286 weingart plier n nspecification: n ntungsten carbide tipped n 287 westcott curved tenotomy scissors n nspecification: n n19mm / 21mm made of stainless steel 288 who probe n nspecification: n na. clinical nb. epidemiological n na. clinical – 0.5 mm ball at the tip, making at 3.5mm, 8.5mm, 11.5 mm, colour coding 3.5 5.55 mm nweight – 5 gm nb. epidemiological marking at 3.5 mm & 5.5 mm n0.5 mm ball at the tip 289 williams probe n nspecification: n nfor use in periodontal surgeryth marking at 1, 2, 3, 5, 7, , 9 & 10mm 290 wire cutter n nspecification: n nmade of hard tempered steel n 291 wire tucker n nspecification: n nfor orthodontic work. tungsten carbide tipped 292 wooden / plastic slide boxes n nspecification: n nframework with finger joints fabricated out of teakwood with sunmica top and plywood bottom. wooden grooves for standing 3”x1” glass slide in vertical position individually. inside bottom covered with velvet and inside top with printed index. provided with brass chromium plated hinges clips and card frame. finished in natural color niro cellulose lacquer. 293 wooden mallet n nspecification: n nhaving wooden head that is10 cm in length, round at one end of diameter 3 cms while tapered at other end, handle length 28 cms nfor prosthodontic laboratory use 294 woodson periosteal elevator n nspecification: n ndouble ended one end curved ( curved working end length: 10 14 mm, width: 5 6mm ) nflat tapered end: length – 14 16 mm, width at the widest point 4 6 mm...

Health And Family Welfare Department - West Bengal

21324641 e tender for procurement of dental items used in dentistry for two years from the date of award of contract ( aoc ) 1 3rd generation 2 6th generation 3 acryliser n 4 adam’s plier with tungsten carbide tip n nspecification: n nfor orthodontic work. n 5 adam’s plier n 6 adson forceps, toothed n 7 adson’s forceps non toothed n 8 air polisher n 9 aluminum slide trays n nspecification: n nmade of aluminum ntray dimensions: 11.25 x 7.25 x 0.25 in.holds 20 each of 25 x 75 x 1mm slides 10 amalgam carrier n nspecification: n nmade of stainless steel 11 amalgam plugger n nspecification: n nmade of stainless steel double ended 12 amalgamator with plunger n nspecification: n n• input voltage 220 230v n• provided with touch pad selector n• pre programmed time setting n• quiet, high speed mix capsules n• built in automatic timer n• capsule holder accepts all types of amalgam capsule n• with plunger n• customized trituration times 13 anatomical articulator n nspecification: n n1. rust free construction. n2.fixed condylar guidance with spring mounted elements that are attached to upper member n3. incisal pin. 4. mid incisal pin n5. orientation rod, 6. incisal guide table n7. support upper & lower plaster cast 14 anterior jacquette n nspecification: n nset of three. ( 1 pc straight & two pc curved ) nmade of high quality stainless steel. 15 apexo elevators n nspecification: n nset of two set of right & left made of stainless steel. 16 austin’s retractors n nspecification: n nl shaped with one rounded end and one forked end nmade of stainless steel 17 babcock’s forcep n nspecification: n nfinger ring, ratcheted, non perforating forceps used to grasp delicate tissue nmade of stainless steel 18 band contouring pliers n nspecification: n nfor orthodontic work. made of hard tempered steel 19 band cutting scissors n nspecification: n nfor orthodontic work. nmade of hard tempered steel 20 band pinching pliers set n nspecification: n nset of 1 piece each ofleft & right nfor orthodontic work. made of hard tempered steel 21 band pusher n nspecification: n nfor orthodontic work. made of hard tempered steel 22 band remover anterior & posterior n nspecification: n nfor orthodontic work. made of stainless steel 23 band seater n nspecification: n nfor orthodontic work. made of hard tempered steel 24 binocular compound microscope n nspecification: n nsharp image display with excellent optical function, small space occupancy with integral stand design, low environment requirement with anti mould technology. ncomfortable operation with ergonomic design principle nviewing head: compensation free binocular head inclined at 30o interpupilary distance 55 75mm neyepiece: wide field eyepiece wf10x / 18mm with eye guard, achromatic objective 4x, 10x, 40x, 100x, nfocussing range: co axial coarse and fine adjustment range 13mm fine division 0.002mm with tension control. nnose piece: quadruple nosepiece, nstage: double layer mechanical stage 140 x 140 mm / 75 x 50 mm n.a1.25 abbe condenser with iris diaphragm and filter. nfocussing: coaxial coarse & fine adjustment system range 24mm, fine division 2mm nillumination: led light with brightness adjustable. iso 13485 or ec certificate / directive 93 / 42 / eec ) 25 block holders n nspecification: n nto be used to hold paraffin blocks and not made of plastic 26 blow torch n nspecification: n nfor casting procedure: nmade of non corrosive high fusing alloy nprovided with air flow regulator, two separate inlet line for lpg gas & oxygen 27 boley gauge n nspecification: n nmade of stainless steel for measuring tooth dimensions & others. 28 bone expansion and splitting kit n nspecification: n nthe kit consists of nosteotomes set of 5 6 of various diameters nspreaders n burs surgical for bone removal n saw disc n thumb driver & rachet nautoclavable cassette 1 piece 29 bone file howard type n nspecification: n nstraight or curved working ends nto smooth bone for better contour of alveolar ridge crosscut or straight cutting ridges double ended nmade of stainless steel 30 bone file miller type n nspecification: n ndouble ended made of martensitic stainless steel 31 bone grafting syringe n nspecification: n nfor “tamp and pack” method for placement of graft material into oral cavity. 32 bone rongeur end cutting n nspecification: n nscissor type handle, cutting edges on top edge of beaks made of martensitic stainless steel 33 bone rongeur side cutting n nspecification: n n scissor type handle, cutting edges on side and top of beaks 34 bone shear n nspecification: n nlength 6 8inches.made of stainless steel 35 boon’s gauge n nspecification: n nhigh quality stainless steel framework with minimum nmarking till 6mm 36 bracket debonding plier anterior n nspecification: n n for band removal orthodontic work. tungsten carbide tipped 37 bracket debonding plier posterior n nspecification: n nfor band removal in orthodontic work. tungsten carbide tipped 38 bracket holding tweezer n nspecification: n nfor orthodontic work. made of hard tempered steel 39 brass flask size no 6 n nspecification: n nfor acrylic denture fabrication by compression moulding, with detachable upper, body & lower member with keyways. made of brass 40 buck knife n nspecification: n nsize ¾ & 5 / 6 for use in periodontal surgery 41 bur chuck for dental lathe n nspecification: n nof different shapes for attaching abrasive stone point, stone wheel & other attachments 42 buser bone chisel n nspecification: n n6mm pointed tip made of martensitic stainless steel alloy 43 camel hair painting brush size 04 44 canine contouring plier n nspecification: n nfor orthodontic work. made of stainless steel 45 casting ring extra large n nspecification: n ncasting ring extra large nmade of steel nfor use with centrifugal casting machine nlength 4 & diameter x 4.75or more 46 casting ring large n nspecification: n nmade of steel nfor use with centrifugal casting machine . nlength3 & diameter x 3.75 47 casting ring medium n nspecification: n nmade of steel for use with centrifugal casting machine . nlength2 & diameter x 2.75 48 casting ring small n nspecification: n nmade of steel for use with centrifugal casting machine . nlength1.25 & diameter x 1.75 49 casting tong n nspecification: n nmade of stainless steel or high fusing alloy for holding casting ring 50 castrovejo needle holder n nspecification: n ncastroviejo microsurgical needle holder is a double spring instrument used for holding small, delicate needles in various microsurgical procedures. it also features a locking mechanism.made of stainless steel, autoclavable 51 castroviejo scissor n nspecification: n ncastroviejo scissor has curved blades. nultra sharp blades microscopic serrations provide a smooth cut. nspring loaded knurled handles provide the control you need to make perfectly smooth cuts in delicate materials. nstainless steel, autoclavable 52 cement mixing spatula n nspecification: n nmade of stainless steel double ended 53 ceramic sculpturing & finishing kit n nspecification: n ncomprising of high quality sable hair / synthetic filament brush size one zero, two zero and four zero and other sizes, ceramic curver, mosquito forcep, tweezer, ceramic pallete for mixing ceramic powder and other associated carving & finishing instruments. 54 chandler chisel with 5mm tip n nspecification: n nwide single bevelled blade chisel nmade of martensitic stainless steel alloy 55 chanel retractor n nspecification: n nlength 17.5 cm, made of stainless steel 56 chin retractor obwegeser type n nspecification: n nlength 15.5 cm, made of stainless steel 57 chisel curved n nspecification: n nchisel curved 20mm nmade of martensitic stainless steel 58 circular saw n nspecification: n nfor dental model cutting: with self illumination nprovided with motor driven circular saw blade and cast holding platform, electrically operated motor driven with push button type on off switches. 59 clinical micromotor brushless n nspecification: n nelectrically operated with handpiece nhandpiece autoclavable upto 135 degree celcius, handpiece speed 1000 40000rpm, speed maximum output power 1.2w, 3.4 3.5 ncm torque, with option of clockwise & anticlockwise rotation. n control box and foot control mechanism. 60 colorado needle and accessories. n nspecification: n nelectrosurgical needle is needle electrode for use in monopolar electrosurgical handpiece made of tungsten carbide. coagulation tips & cutting tipsshould work with most of the diathermy units available in the hospital , operating frequency above 3 mhz. niso / fda / ce 13485 or ec certificate ( directive 93 / 42 / eec ) 61 composite curing unit system n nspecification: n nfor indirect composite work nchamber provided with sliding tray, provided with multiple halogen or led lights light intensity not less than 900 mw / cm2output peak wavelength range 450 490 nm ( intensity maximum at 460 nm ) ncapable of curing indirect composite veneers / inlays n. curing chamber dimension : nlength 10 inches nwidth 7 inches nheight 4 inches or more nelectrically operated 220 230 volts nportable with timer 62 cooley bulldog clamp n nspecification: n nstraight 8.6cm jaw 4.7cm made of stainless steel 63 coplin staining jar vertical type 64 crane kaplan pocket marker n nspecification: n npair of two instruments –right & left 65 crane kaplan scaler n nspecification: n n double ended, round handled periodontal instrument for the removal of heavy supragingival calculus. it is a sickle type scaler, with a strong, rigid, sharply angled blade 66 crown gauge ( iwanson caliper ) n nspecification: n nfor measuring thickness of wax pattern, metal casting. nboth sided scale 0 10mm 67 crucible for small casting n nspecification: n nmade of fused silica / ceramic material, capable of withstanding high temperature for use with centrifugal casting machine 68 curing pressure pot n nspecification: n n5 liter or more capacity npressure pot temperature is preset to approximately 120°fand manually adjusts to a maximum 160°f. nsolid clad bottom provides even heat distribution. nincludes an easy to read, built in pressure gauge and quick release air valve. nthe pot has a safety device to prevent overheating, and a secure double locking lid. neasy to clean stainless steel interior. npot holder to keep pot firmly nin place. nwith lid gasket 69 cushing nerve hook n nspecification: n nused for the retraction of nerves or delicate tissue during neurosurgery. nthe instrument has a ball tip to avoid tearing. this #1 hook is angled 90 degrees with a 4mm ball tip and overall length of 7 1 / 2 inches 70 dandy type nerve hook n nspecification: n n length 16 20cm ntip 4 5mm, deep working tip blunt ended made of stainless steel 71 dappen dish made of glass 72 de la rosa wire contouring plier n nspecification: n nfor orthodontic work. made of stainless steel 73 deans scissors: n nspecification: n nscissors with 1 serrated angular blade used for trimming tissue or cutting sutures. 74 debackey’s forceps n nspecification: n n length 26 cm, tip width 1.5 mm made of stainless steel 75 debackey’s vascular forcep 6” n nspecification: n nmade of stainless steel, autoclavable 76 debakey bulldog clamp 8.5cm n nspecification: n nwith serr.jaws, straight made of stainless steel 77 dental dewaxing unit n nspecification: n nwith digital control for water temperature regulation. construction: stainless steel ntank sizes ( 300 x 200 x 350 mm ) approximately nwater filling: manual heater: 2000 watts. with drain valve 78 dental excavator discoid type n nspecification: n nmade of stainless steel double ended niso 13397 4:1997 79 dental lathe motor n nspecification: n nac, hp 1, universal, rpm 2800, equipped with double b.b, single speed, rating continuous with 3 chucks ( buffer, stone & bur chuck ) , three imported b.b. flexible metal cable arm and its attachment. 80 dental muffle furnace n nspecification: n n1150c degree celsius, working temperature 900 degree celsius, with er & digital display nmuffle size 175x175x225mm. 4.0 k.w. capacity 81 dental phantom head unit n nspecification: n nmanikin head fixed with a table, with mounted upper & lower jaw containing screw mounted teeth having 90° swiveling function of head unit, provided with control box for micromotor, foot control & micromotor with contra angle handpiece, should have mounted light unit with illumination power not less than 7000 lux. 82 dental plaster dispenser n nspecification: n nbody made of stainless 304 grade, fitted with digital electronic timer, capacity 5 kg or more. will dispense premeasured dose of plaster at touch of a button. 83 dental steam cleaner n nspecification: n npower 1500w or more, 220v, frequency 50 / 60hz. working pressure: 4 5 bar. capacity 5 10litre. with thermostat controller.device with both steam gun & button / lever controlled steaming attachment with steam regulator. stainless steel non rusting inner tank body. 84 dental surveyor tool kit n nspecification: n ntools nanalyzing rod multiple undercut gauges n carbon marker sheath n wax trimmer 85 dental surveyor ney’s type n nspecification: n ndental surveyor ney’s type nhorizontal platform n• adjustable spindle for the vertical indicator n• survey table that can be locked at any angle. nwith tools analyzing rod undercut gauges n carbon marker sheath n wax trimmer etc nprovision for holding micromotor handpiece nstandard packaging / physical verification of sample may be made 86 dental tweezer n nspecification: n nwith horizontal serrations at tip, diamond knurling on the outside for good grip, stainless steel alloy 87 dental vacuum former machine n nspecification: n nelectrically operated, with inbuilt vacuum motor suction unit, heating element with on off switches & adjustable clamping plate. nspecifications: nvoltage : 230v / 50 60hz npower : 600w 230v nheater : 400w 230v ndimension : l 23 25 cm, w 17 20 cm 88 dg 16 endodontic explorer 89 diamond glass marker n nspecification: n nmounted in aluminum pencil 5 inches ( 12.7cm ) 90 die cutting machine n nspecification: n nelectrically operated with diamond disc. nwith adjustable model holder nself illuminated chamber 91 dingmans retractor n nspecification: n nwith three blades made of stainless steel 92 distal end bender n nspecification: n nfor orthodontic work. made of stainless steel ) 93 distal end cutter n nspecification: n ntungsten carbide tipped ncutter for all types of wire up to a maximum of .021” x .025” ( .53 mm x .64 mm ) 94 distal end cutter n nspecification: n nfor orthodontic work. made of stainless steel 95 dontrix gauge n nspecification: n nspring balance type, minimum measurement till 500 ngms to precisely calibrate orthodontic force there are two units of measurement ounce and gram. measuring range: 0 450g / 0 16 oz. to measure tension and compression force 96 double wax heater pot n nspecification: n nwith thermostat controlled temperature regulator electrically operated 97 dry model trimmer n nspecification: n n with attached suction unit 98 duplicating flask n nspecification: n n a. programmable brushless agitator motor ntemperature controls for precision warm up and cool down phases nintelligent heating strategy and provision for effective disposal of gel and prevention of nozzle blockage nmaintainance of consistent gel quality nvoltage: 200230v, 50 / 60hz, nb. pressure compaction unit for duplicating silicone materials nautomatic mixing and metering unit for two component silicone material nduplicating flask: n ( a ) individual aluminium duplicating flask with aluminium top and rubber base and 2 base formers ( 2 sizes ) n ( b ) duplicating flask with stabilizing insert and three replaceable palatal formers of different sizes 99 electrically operated wax carver n nspecification: n nelectrically operated electrical wax curver with thermostat controller. with two detachable carving tools 100 electro polisher n nspecification: n nautomatic digital electro polisher, auto / manual modes, nwith trimmers, electrolyte flow regulation n38 mm disc for psa paper & cloths nsupply 230 v. ac ncurrent – 2.5 amp., voltage – 80v, supply – 230 v.a.c.polishing probes – unique pen type system with recirculation of electrolyte, pump 25 watts reservoir ( 0.5 ltr ) 101 endo activator n nspecification: n nsystem kit that includes handpiece / driver nbox of small, medium & large activator tips. nbox of 100 protective barriers. safe & vigorous energetising intracanal irrigant, capable of debriding & disinfecting root canal system 102 endodontic microsurgical equipment n nspecification: n ncomprising of na. ultrasonic piezoelectric scaler with inbuilt irrigation , led & water tank nb. ultrasonic endodontic retro surgical tips ( for anterior teeth upper & lower and posterior teeth of upper and lower arch ) nc. ultrasonic passive irrigation, nd. set of assorted ultrasonic tip for instrument retrieval and chasing calcified canal 103 endomotor with torque control nhand piece. n nspecification: n ncontinuous & / or reciprocating motions for root canal shaping, hand piece with integrated on off switch, auto reverse mode, speed 250 1200 rpm. n torque range 0.6 4 ncm, n multiple adjustable programs nstandard packaging / physical verification of sample may be made 104 endovac irrigation system n nspecification: n n multiple port adapters, hand piece set, extra evacuation system, cannulas, delivery tips & syringes. 105 excavator oval type 106 excavator spoon type n nspecification: n nexcavator double ended spoon type 107 extraoral gothic arch tracer n nspecification: n njaw movement recording and centric relation npositioning, one stylus and one tracing plate nattachments to the jaw movement recording bases noutside the mouth nstandard packaging / physical verification of sample may be made 108 farabeufs periosteal elevator n nspecification: n nof different sizes length 6 8inch, width 8 12mm, made of stainless steel. 109 fergusons mouthgag n nspecification: n nmade of stainless steel n 110 fiber optic light n nspecification: n nfiber optic based lighting unit consisting of fiber optic cable, led based portable light with controller unit. with rechargeable battery niso 13485 or ec certificate ( directive 93 / 42 / eec ) 111 flask clamp for brass flask n nspecification: n nmade of steel with clamp compatible with brass flask of size no 6 112 frahm amalgam curver 113 furcation curettes quetin n nspecification: n nbuccal lingual 0.9mm 1pc quetin buccal limgual 1.3mm 1pc nquetin mesial distal 0.9mm 1 pc quetin mesial distal 1.3mm 1pc nconform to iso 13485:2003 / en iso 13485:2012 114 gardner chisel with 3mm tip n nspecification: n nsingle bevel chisel nmade of martensitic stainless steel alloy 115 gates glidden drill set n nspecification: n nstainless steel, drill compatible with latch type handpiece for use in bulk removal of the tooth structure nunit pack containing six different sizes each drill having 28 32 mm length. 116 gillie’s skin hook doubleprong n nspecification: n nmade of stainless steel n 117 gillie’s skin hook single prong n nspecification: n nmade of stainless steel n 118 glass bead sterilizer n nspecification: n nelectrically temperature regulated to heat contained glass beads with on off switch. nsmall rectangular base for keeping at chairside nprovided with lid. n it should reach operating temperature of approximately 240 c to 270 c in 15 20 minutes time. nsterilization is on contact with glass beads nunit can be left in the “on” position all day and is safe for use in laminar flow cabinets. 119 glass slab 8mm thick n nspecification: n ntransparent rectangular glass slab thickness 8mm, length 6” x 4” inch 120 glass slab big n nspecification: n ntransparent square glass slab thickness 4mm, each side of 6 inch 121 glass slab small n nspecification: n ntransparent square glass slab thickness 4mm, each side of 3.5 inch 122 goldmanfox periodontal probe n nspecification: n ndouble ended probe, markings at 1, 2, 3, 5, 7, 8, 9& 10mm.high quality stainless steel with satin finish, antimagnetic rust resistant, acid resistant 123 gracey curette set n nspecification: n nof 9 size ½, ¾, 5 / 6, 7 / 8, 9 / 10, 11 / 12, 13 / 14, 15 / 16, 17 / 18.made of hard tempered steel ndouble ended nhandle 10.2 10.8cm nshank 3.1 3.6cm nlength 6.8 7.4mm noffset blade beveled at 60 70 degree to the shank n1.triple tempered steel n2.satin steel handle n3.corrosion resistant n4.rust resistant n5.stain resistant n6.can be sharpened by traditional sharpening stones nconform to iso 13485:2003 / en iso 13485:2012 iso 13485 or ec certificate ( directive 93 / 42 / eec ) ce & fda aprroved 124 guarded nasal chisel set of right &left n nspecification: n nsize : 4, 5, 6, 8mm right & left in pair made of stainless steel 125 half round plier n nspecification: n nfor orthodontic work. made of hard tempered steel 126 hand scaler set of 5 piece n nspecification: n nset containing 1 piece each of: sickle, push, universal, broad right & left . 127 hard wire cutter n nspecification: n nhard wire cutter made of tungsten carbide tipped 128 heavy duty lathe with suction unit n nspecification: n nelectrically operatedheavy duty motor unit having power not less than – 0.5hp nhigh speed r.p.m. 3000 rpm narrangement to attach bur holding chuck – electroplated spindle on one side for polishing buff wheel, on the other arm is a grinding stone wheel of diameter 2.5 inch or more. provided with nbuilt in high power dust suction unit for clean, unpolluted, dust free work environment, attached with dust collection bag – easily removable tray for debris collection. ntable mountable heavy base plate for vibration free operation nbuilt – in lighting for high visibility 129 heavy wire cutter n nspecification: n nwire cutter tungsten carbide tipped n 130 hinge articulator n nspecification: n nrust free construction npermit opening & closing in hinge like motion. support upper & lower cast. n upper member adjustable with locking nut. 131 hook crimping plier n nspecification: n nfor orthodontic work. made of stainless steel 132 hot plate with wooden handle 133 howarth’s periosteal elevator n nspecification: n ndouble ended: one end flat, broad sharp edge, other end rugine ended made of stainless steel 134 howe’s pliers anterior n nspecification: n nwith serrations, useful for placement and removal of archwires, pins and other auxiliares nmade of stainless steel 135 howe’s pliers posterior n nspecification: n npliers with serrations, useful for placement and removal of archwires, pins and other auxiliares 136 humby’s knife holder n nspecification: n nmade of stainless steel n 137 hydraulic press n nspecification: n nthe closed circuit hydraulic press should work with a pressure up to 7000 kg of thrust. n it can contain up to three flasks at a time. nthe structural elements in chromium plated steel. n provided with dial. 138 hydro solder n nspecification: n nmains voltage: 1 x 230 v, mains frequency: 50 x 60 hz, mains fuse: 1 x 10. a nmax.gas production: 6 liter nmax. nozzle size: 0.07mm n dimensions w x h x d x ( mm ) : 330 x 230 x 310 mm nweight: 22 kg ncapacity: 110lt, with accessories 139 implant microsurveyor n nspecification: n nwith compass surveying system, portable hand held surveyor 140 implant retractor n nspecification: n nmade of stainless steel. autoclavable 141 incubator n nspecification: n nrobust construction nflawless finish nlong functional life ninner chamber size 14 x 14 x 14’’ with two shelves nwith thermostat control & digital display iso / fda / ce or ec certificate 142 inlay wax curver double ended 143 instrument sharpening kit with arkansas stone n nspecification: n n flat arkansas stone with conical shape nplastic test stick ( 5 ) nstone oil nmagnifying lens& other accessories 144 intra oral camera with video monitor n nspecification: n na ) camera: neasy to use, narrow head, comfortable for patient intra oral camera with provision of variable lens adjustment that can be attached to dental chair unit nvideo compatible so that images can be displayed on a computer workstation / lcd monitor nstill image resolution: 1024 ( h ) x 768 ( v ) or more nvideo resolution: 640 ( h ) x 480 ( v ) or more nfocus range: 1 mm 25 mm nlens surrounded by led lamp ninput: 220v 50 60hz noutput: 5v, 2a 145 intraoral camera with fluorescent technology n nspecification: n nintra oral camera with caries detection and periogingival inflammation detection facility based on flurescent technology 146 intraoral sand blaster n ( microetcher ) n nspecification: n nlong tubing with compatible adapter for the airotor handpiece point nof the dental chair, fully autoclavable, 50 microns naluminium oxide particle size, 360 degree adjustable nozzle. 147 intraoralgothic arch tracer n nspecification: n njaw movement recording and centric relation npositioning, one stylus and one tracing plate nattachments to the jaw movement recording bases ninside the mouth n 148 kilner’s cheek retractor n nspecification: n nmade of stainless steel n 149 kirkland gingivectomy knife n nspecification: n nfor use in periodontal surgery n 150 kocher’s forceps n14cm hemostatic forcep. n nspecification: n n it is specifically designed to catch the bleeder that are deep within tissue hence it is ideally used on tough structures made of stainless steel 151 laboratory micromotor with brushless motor n nspecification: n ncompact and portable size, continuous variable speed control , r.p.m 1000 40000, on / off foot switchone touch change of the driving direction for efficient operation with brushless motor with handpiece 152 laboratory micromotor with carbon brush motor n nspecification: n ncompact and portable size, continuous variable speed control , r.p.m 1000 40000, on / off foot switchone touch change of the driving direction for efficient operation with carbon brush motor with handpiece 153 langenback’s retractor n nspecification: n nmade of stainless steel n 154 laser guided pin drilling system with pins n nspecification: n nelectrically operated 110v / 240v, laser guided pinsetter, pin drilling for easy die pin attachment. nlaser light technology with carbide bur drill with high speed motor. nto accurately drill parallel holes into the underside of the model die pins of various sizes ( 1000 pieces total ) made with non corrosive alloys for use with pindex system of die pins. 155 lead apron n nspecification: n nadult size, 0.5 mm thick lead covered with cotton on nboth sides, overstraps, buckles & hand gloves ( size 6 nto 7.5 ) with 0.5 mm thickness lead 156 lecron wax n nspecification: n ncurver made of steel n 157 leuckhart pieces n nspecification: n ntwo l shaped metallic stands for preparing paraffin wax block 158 light cure unit n nspecification: n n led based. light modes fast, ramped & pulsed ndisplay for mode & timer nselection nchordless with rechargeable lithium battery nlight intensity not less than 1200 mw / cm2output peak wavelength range 450 490 nm ( intensity maximum at 460 nm ) nwith inbuilt timer, on off switch 159 lingual arch plier n nspecification: n nfor orthodontic work. made of stainless steel 160 loop forming plier n nspecification: n nfor orthodontic work. nmade of hard tempered steel 161 loop forming plier n nspecification: n nfor orthodontic work. made of stainless steel 162 lower molar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint set of one piece right & one piece lower molar forcep 163 lower premolar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 164 lower roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip 165 lower universal forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint set of one piece right & one piece lower molar forcep 166 magnification loupes 3.5x n nspecification: n nergonomically designed binocular loupe that can be worn over spectacle frame capable of 3.5x magnification at 420mm with 3watt led rechargeable light 167 magnification loupes 4.5x n nspecification: n nergonomically designed binocular loupe that can be worn over spectacle frame capable of n4.5x magnification at 420mm with 3watt led rechargeable light n 168 magnifying work lamp n nspecification: n nwith flexible & adjustable stand and base. inbuilt led based optical illumination system. nglass lens diameter 7 inches or more, magnification power upto 4 x 169 manual crown remover n nspecification: n n with adjustable spring with crown remover tip ¬ 2 single crown remover contrangled tip ¬ 3 open¬end adjustment wrench 170 manual press n nspecification: n nwith base and cross bar made with high strength steel. nthe structural elements made with chromium plated steel. ncapable of pressing upto 1 to 3 flasks at a time. nbase should have holes for attachment to bench 171 marquis colour coded probe n nspecification: n nfor periodontal surgery made of stainless steel colour coded at 3 6 & 9 12 mm 172 mathieu plier n nspecification: n nstraight & curved for orthodontic work nused for ligature typing and placing of elastics 173 mbt gauge n nspecification: n nfor .022” slot nfor orthodontic work. made of stainless steel 174 metal impression tray non perforated n nspecification: n nmade of non corrosive alloy nfor edentulous patient set of upper & lower, size 0, 1, 2, 3, 4. n ( price being same to be supplied as per requirement of user ) 175 metal impression tray perforated n nspecification: n nfor dentulous patient nmade of non corrosive alloy nset of upper & lower, size 0, 1, 2, 3, 4. n ( price being same to be supplied as per requirement of user ) 176 metal suction tip n nspecification: n na ) 3mm diameter 10 pc nb ) 5mm diameter 10 pc nmade of stainless steel 177 micro oscillating saw n nspecification: n ncapable of easily cutting channels and bone blocks nmaximum 12, 000 oscillations per minute. compact design for easy access . ntwo shaft lengths & 4 blade sizes for optimum access. nincludes external irrigation port for effective bone cooling nuniversal e type coupling that fits implant motor unit 178 microhead air rotor handpiece n nspecification: n nsuitable for use in child patient, head size 8.5 x 19.4 mm, provided with water spray, body made with ceramics autoclavable, rotational speed 3, 00, 000 to 450, 00, 00 rpm, provided with a bur changer & wrench. nphysical verification required 179 micropipettes n nspecification: n nfeature built in tip ejectors and autoclavable tip cones. should work on a click stop digital system, are easy to calibrate and maintain, and easy to disassemble for autoclaving. manufactured as per iso 9001:2008. each pipette should be individually calibrated according to iso 8655 standards.calibration certificate must be provided with each pipette. accuracy and precision values should be those laid down in the iso 8655 standards.built in, streamlined tip ejector facilitates easy tip ejection and access to narrow necked bottles and tubes. variable volume pipette: 50 200 μl. increments [ μl ] : 1 9 volume [ μl ] : 50 to 200. accuracy ( ± ) %: 0.6 to 1 11 precision ( ± ) %: 2 to 0.3 12 it should be ce mark 180 microvascular instrument kit n nspecification: n nkit comprises of n1.micro scissors n2.micro needle holder n3.jwellers forceps n4.vessel dilators n5.liga clips ( no.100.no.200 ) n6.ligaclip applicators n7.vessel clamp ( 2a, 2v, 3a, 3v ) n8. vessel clamp applicator n9. hand held colour doppler unit n10.pneumatic tourniquet nspecification to be quoted by the bidder / manufacturer nmicro scissors ni ) adventitia scissors flat handle , 8mm wide, straight length of 15cms, blades 19mm – 5 pcs nii ) dissecting scissors – flat handle, 8mm wide , curved, length of 15cms, blades 19mm – 5 pcs niii ) adventitia scissors round handle, 8mm diameter of tip, straight, length 15cms, blades 12mm – 5 pcs niv ) dissecting scissors – round handle, 8mm diameter of tip, curved, length 15 cms, blades 12mm – 5 pcs nmicro needle holder: ni ) flat handle , 8mm wide, curved, 14 cms length – 6 pcs nii ) round handle, 8mm, curved, 15 cms length – 6 pcs njewellers forceps ni ) flat handle , 9mm wide, straight, 13.5 cms length – 6 pcs nii ) flat handle , 9mm wide, angulated 45 degrees, 13.5 cms length – 6 pcs niii ) round handle , 8mm wide, straight, plateau, 15 cms length – 6 pcs nvessel dilators: ni ) flat handle , 9mm wide, angulated 10 degrees, nlength 11cms – 6pcs nliga clips – made of stainless steel, autoclavable. nno.100 – 150 sets ( each set containing 6 liga clips ) nno.200 150 sets ( each set containing 6 liga clips ) nno.400 – 100 sets ( each set containing 6 liga clips ) nligaclip applicator: ngrooves on inside jaw surfaces of applier which helps in increasing of jaw clip security. nangled jaws to improve visibility beyond structures nmechanical stop. nmade of stainless steel and autoclavable. 181 mini pin & ligature wire cutter n nspecification: n ntungsten carbide tipped ncuts soft wire pins and ligature wire up to .012” ( .30 mm ) 182 miscellaneous hi n nspecification: n n139 plier for orthodontic work. made of stainless steel 183 miscellaneous hi 184 model trimmer with carborundum disc n nspecification: n nmotor rpm 2800 heavy duty, equipped with two ball bearing single speed, rating continuous with buffer and 10 carborundum disc , with heavy base that can be clamped and installed on underlying table, with water inlet and out flow water system. 185 model trimmer with diamond disc n nspecification: n n1 / 2hp, rpm 2800, heavy duty equipped with two ball bearings, single speed, rating continuous with buffer and one 10 diamond disc rough or fine without suction.1 piece spare diamond disc to be provided 186 model trimmer with double disc n nspecification: n none diamond & one carborundum disc n rpm 2800 double motors horsepower 1 / 2 or more each, heavy duty, equipped with two ball bearings each motor, single speed, rating continuous with fixed one10 diamond disc fine, one carborundum coarse cutting wheel, base inlet, with outflow water system. 187 molts elevator n nspecification: n nlength 7”double ended with one round, blunted end and one pointed end made of stainless steel 188 mouth prop n nspecification: n nautoclavable made of stainless steel with rubber pads for intra oral use over occlusal surfaces during surgery. the rubber pads are of 4 sizes attached by a stainless steel chain. 189 naber’s probe n nspecification: n nfor use in periodontal surgery double ended furcation probe nconform to iso 13485:2003 / en iso 13485:2012 190 omega loop forming plier n nspecification: n nfor orthodontic work. made of stainless steel 191 orban gingivectomy knife n nspecification: n nfor use in periodontal surgery n 192 oschenbein chisel curved n nspecification: n nsize no. 1 and no. 2 ochsenbein chisels periodontal chisels. they havethree cutting edges, a flat edge on the tip and a curvededge on each side of the tip. 193 oschenbein chisel straight n nspecification: n n17.5 cm x 4 mm nsize no. 1 and no. 2 ochsenbein chisels periodontal chisels. they havethree cutting edges, a flat edge on the tip and a curvededge on each side of the tip. 194 osteotome 20mm n nspecification: n nmade of stainless steel n 195 paeso rimmer drill set n nspecification: n nstainless steel, drill compatible with latch type handpiece for use in bulk removal of the tooth structure nunit pack containing six different sizes each drill having 28 32 mm length. 196 palatal trimmer n nspecification: n nprovided with1 fast cutting trimmer, electrically operated , rpm 2600 or more nbody made with 304 grade stainless steel, or non rusting alloy. dull finished work surface, dust collection with adapter hose, provided with1 fast cutting trimmer 197 paquette blade handle 198 paraffin wax bath ( thermostatically controlled ) n nspecification: n nconstruction – double walled effectively insulated.wax tank of 20 gauge ss sheet. fitted with laminated wooden rim and anodized alumininium cover mounted on 5 cm diameter. nheater two 1 kw each special wax heater. nheat control thermostat to control temperature fron 30 degree c to 110 degree c nfinish externally finished in oven baked naccessories power plug, 1 brush for wax application and aluminium sheet mesh for heater. 199 pediatric extraction lower incisors & canine forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 200 pediatric extraction lower molar forcep n nspecification: n nfor children nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, n 4.5 inches of length 201 pediatric extraction lower premolar forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 202 pediatric extraction universal forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 203 pediatric extraction upper incisor & canine forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 204 pediatric extraction upper molar forcep left n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 205 pediatric extraction upper molar forcep right & left n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 206 pediatric lower roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 207 pediatric upper roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc type of hinge joint, 4.5 inches of length 208 piezo surgical kit n nspecification: n n device with intermittent operation, 60 sec on then 30 sec off with irrigation, & 30 sec on 120 sec off without irrigation, power supply 240v, 50 / 60 hz, maximum power absorbed 120va. surgical tip capable of modulating from 10 to 30 or more. 29khz or more. power adjustable from 2.8 to 16w. tip vibration in range of 60 200μm.motor with tips & other accessories n ( european ce / fda ( usa ) approved ) 209 pikling kit n nspecification: n nelectrically heated and thermostatically controlled pickling unit for acid based pickling agents with low power consumption for pickling of precious metals. swivel sieve and housing made of shock proof and acid resistant polypropylene material 210 pin & ligature wire cutter n nspecification: n ntungsten carbide tipped ncuts soft wire pins and ligature wire up to .015” ( .38 mm ) 211 plaster knife n nspecification: n nwith working length not less than 2 .5inches 212 plaster spatula n nspecification: n nround ended steel spatula having width of 1.25 inch & length 5 6 inches, with plastic or wooden handle 213 plastic filling instrument nward type 214 pneumatic crown remover n nspecification: n npneumatic, autoclavable tips, basic kit includes easy pneumatic crown and bridge remover bridge remover tip ¬ 1 single crown remover tip ¬ 2 single crown remover contrangled tip ¬ 3 open ¬ended adjustment wrench rubber gasket flexi¬wire set 215 pneumatic deflasking unit n nspecification: n n operates on air pressure. nwith handheld chisel provided with detachable tips n provided with variable powercontrol with air inlet and tubing length not less than 1.5 meter. nworking pressure 1 6 bar 216 portable transcutaneous electrical nerve stimulation ( tens ) n nspecification: n nunit for pain management with replacement electrodes. the machine should have burst, continuous and modulation pulse modes. dual, isolated between channels with a pulse intensity of 0 80ma peak into 500ohm load. pulse rate of 2 120hz adjustable. pulse width 40 260 microseconds, adjustable. maximum voltage: 110v. maximum charge: 21microcoulombs per pulse 217 pressure moulding machine n nspecification: n nthe unique thermally controlled heater reaches working temperature in few minutes. npower: 230 v, 850 w nworking pressure: 0, 5 – 6, 0 bar nmeasurements ( w x h x l ) : 450 x 230 x 260 mm 218 pulp tester digital n nspecification: n npreset stimulus speed mode, battery 9v, auto off after 3 min, with autoclavable tips, one touch operation, with digital read out of display 219 punch biopsy forceps n nspecification: n nmade of stainless steel n 220 rib raspatory right & left n nspecification: n nmade of stainless steel n 221 rib shear ( doyan ) n nspecification: n nmade of stainless steel n 222 ribbon arch plier n nspecification: n nfor orthodontic work. made of stainless steel 223 rme bender n nspecification: n nfor orthodontic work. made of stainless steel 224 robinson black bristle brush n nspecification: n nhaving diameter of not more than 2.5 inch. 225 root canal explorer 226 rowe zygomatic elevator n nspecification: n nmade of stainless steel n 227 rubber bowl n nspecification: n nsize large n13 cm in height made with flexible synthetic rubber material 228 rubber dam kit n nspecification: n nrubber dam clamp forceps nrubber dam punch nrubber dam frame adult nuniversal rubber dam template nfdi rubber dam nprovided with different clamp designs such as molar clamps, bicuspid clamps winged, labial clamps winged nit contains: n plastic dental dam frame 6 / 5 n wedjets stabilizing cord pack ( s ) n hygenic template 6 / 5 n punch n forcep n rubber dam sheets 6x6 ( 36 ) / pedo 5x5 ( 52 ) n set of 9 clamps adult / set of 6 pedo 229 sand blaster unit n nspecification: n nself illuminated chamber. unit with ventilation slits with rubber gloves, pressure regulator, air filter , provided with glass pane. flow of blasting material from 1 to 6 bar. with wear resistant nozzle tip attached with wear & tear resistant hoses & nozzles. with filter. micro & macro mode 230 sanders knife nsize 1 / 2 231 schluger bone file for use in periodontal surgery 232 self adjusting endodontic file system ( saf system ) n nspecification: n ndigitally controlled endodontic micromotor with peristaltic pump. n self adjusting root canal files, rotary motion with speed and torque control, nreciprocating motion with reverse / forward angular movement 233 self retaining retractor weit laner type n nspecification: n n made of stainless steel n 234 semi adjustable articulator with accessories n nspecification: n nwide view arcon articulator with spring¬ bow, ear¬piece, face bow, orbital indicator, bite fork & other accessories nstandard packaging / physical verification of sample may be made 235 separator placement pliers n nspecification: n nfor orthodontic work. nmade of hard tempered steel 236 sinus lifting instrument kit n nspecification: n nfor lateral & crestal approach n with s reamer / lateral reamers ninitial drill / crestal drills n bone inserter nbone spreader n bone carrier n bone condenser ndepth gauge n chisels of different width n sinus curettes of various designs n bone rongeur forceps nmallet nirrigation syringe & tips n& other instruments nautoclavable cassette 1 piece 237 slide storing cabinet n nspecification: n ncabinet for 1050 slides consisting of 6 drawers each for 175 slides, arranged in single rowframework made of 15mm plywood with top and sides covered with sunmica laminated sheet. 238 slide warming table n nspecification: n ntop surface made of stainless steel ( ss 304 grade ) nthe surface temperature is controlled from ambient to 70°c nsupplied complete with pilot lamp, cord and plug nto work on 220 / 230 volts a.c. supply 239 spirit lamp n nspecification: n nmade of stainless steel nof 100 ml capacity with wick & detachable cap stainless steel body 240 spot welder with soldering attachment n nspecification: n n• electrically operated n• voltage110 240 volts n• applications / indication spot welding n• power settings2, 000 amperes n• heat settings2 n• electrode / tip type hand electrode n• welding positions adjustable 241 steel mallet n nspecification: n nfor use in oral surgical work made of stainless steel length 7.5”, nhead diameter 20 22mm 242 steel slide racks for staining n nspecification: n n the 5 slide gripper can accommodate 5 microscope slides in one staining procedure.it fits most coplin and round open staining jars nit should be made of a special material which is resistant to all chemicals and solvents which are used in staining nit withstands drying temperatures up to 80°c 243 step plier n nspecification: n nfor orthodontic work. made of hard tempered steel 244 surgical elevators coopland’s pattern n nspecification: n nmade of hard stainless steel n 245 surgical elevators cryer’s pattern n nspecification: n nmade of hard stainless steel nlength 145mm, neck diameter 3.6mm, working tip length 9mm for right & left nset of 2 units cryer’s right, left 246 surveyor mounted miling machine n nspecification: n nuniversal precision milling unit. areas of application; wax milling and scraping ; milling, fine grinding, drilling and smoothing of metal with the help of the modeling spindle, it can be used as a surveying instrument and for mounting auxiliary parts. magnetic locking device for model table. drilling depth stop and connection facilities for additional handpiece for finishing. advantages: universal design for measuring, blocking and routing ( router head accept spindles, drawing tools and measuring tools ) . easily movable double articulating arm free from play. routing spindle with quick coupling. controllable, heatable wax knife nrpm can be infinitely controlled from 3000 to 35000 rpm. left / right rotation. route head with micrometer screw for exact vertical bores. good illumination due to integrated led light iso 13485 or ce certificate 247 three prong plier n nspecification: n nfor orthodontic work. made of stainless steel 248 tissue biopsy kit n nspecification: n n1.small and short scalpel blades ( no. 15, 11, 12 or even 5 ) – n 2. mosquito forceps – 2 pc curved & 2 pc straight n3. gauze container made of stainless steel size small 1pc n 4. alley’s tissue forcep 2pc n5. punch biopsy set one piece of three different diameters ( circular blade size 3 mm, 5mm & 7 mm ) in each kit n6. mc indoe’s dissecting scissor1pc n7. bone scoop small1pc n8. bone curette tip diameter 3 mm 1pc n9. sklar tungsten carbide bozeman 10.needle holder 8 tungsten carbide tipped 1 pc with catch, n11. wards needle holder 1pc n12. toothed dissecting forcep 1pc n13. non toothed dissecting forcep 1pc 249 tissue capsules / tissue embedding cassettes n nspecification: n nmade of acetyl polymer;cassettes should keep specimen safely submerged in liquid, efficient flow through slots, snap latch and hinge lock design prevent early separation of base and lid and allows for one hand operation. large labeling area on two sides of cassette. anterior writing area is at 35° angle. npore size: 1mm square pores noutside dimensions: 28.5 x 41 x 6.7mm ( 1.12 x 1.61 x 0.26 ) ninside dimensions: 26 x 30 x 5mm ( 1.02 x 1.18 x 0.2 ) 250 tissue floatation water bath n nspecification: n n ( thermostatically controlled ) inner tank ( single piece ) made of black anodized aluminum. housing made of powder coated aluminum. front panel consist of temperature regulator knob, mains switch and pilot lamp. inside black and outer surface finished in powder paint, with wide enough rim for drying the wet slides. nbath size ( inner ) 225mm*70mm ntemperature controlled by capillary tube thermostat ntemperature range n+5 degree c to 70 degree c 251 torch, alcohol, dental n nspecification: n nwick volume capacity 90ml or more, with adjustable needle point flame, body metal or plastic 252 torquing pliers male n nspecification: n nfor orthodontic work. made of stainless steel 253 torquing pliers male n nspecification: n nfor orthodontic work. made of stainless steel 254 tourniquet arm n nspecification: n nhaving pressure regulator, tubing and connectors with not less than7 cm inflatable cuff 255 tourniquet leg n nspecification: n nhaving pressure regulator, tubing and connectors with wide 14 cm inflatable cuff 256 towel clips ( clamps ) nbackhause type n nspecification: n nto secure surgical drapes and to secure plastic and rubber tubing to drapes features: sharp prong tips 31 / 2 inchand 51 / 4 inch additional use: remove metal temporary crowns made of stainless steel 257 towel cross section clip n nspecification: n nmade of stainless steel used to fix drapes to tissue with minimal trauma during surgical operations 258 tracing table n nspecification: n nbox portable with opaque screen nlight box with led nelectrically operated with ajustbale illumination. box dimension 14” x 16” or more 259 transparency scanner n nspecification: n ndual lens system, minimum 6, 400 dpi optical nresolution, 4.0 dmax for smooth gradation and fine nshadow detection, antireflective noptical coating and nhigh reflection mirror, digital ice technology, 8” x 10” ntransparency unit built into lead 260 trephine bur set n nspecification: n n of 3. dia 2, 3, 4mm nfor harvesting bone cores for use in periodontal surgery iso 13485 or ec certificate ( directive 93 / 42 / eec ) 261 turret n nspecification: n nzero torque ( blue ) nfor orthodontic work 262 tweed plier n nspecification: n nfor orthodontic work. made of stainless steel 263 typhodont articulator n nspecification: n narticulated model with soft pink ( not transparent ) acrylic or plastic gingiva material. included:28 anatomically shaped screwable typhodont ivorine teeth 264 ultrasonic cleaner n nspecification: n n 220v, 100 200watt & above, 5 liter capacity, with stainless steel body &cover. 265 ultrasonic dental scaler n nspecification: n nelectrically operated 220 / 240v 50 / 60hz ac with control box, multi frequency handpiece with scaling tips, foot control, water connector, tube & other accessories. capable of upto 20khz ultrasonic vibrations / second or more niso 18397:2016 / iso / fda / ce 13485 or ec certificate 266 unc 15 periodontal probe plastic n nspecification: n n probe with markings at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15colour coded at 5, 10 & 15mm, thin shanked probe 267 unc 15 periodontal probe: titanium n nspecification: n nprobe with markings at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15colour coded at 5, 10 & 15mm, thin shanked probe nconform to iso 13485:2003 / en iso 13485:2012 iso 13485 or ec certificate ( directive 93 / 42 / eec ) 268 universal columbia curette n nspecification: n ncommon properties: n1.triple tempered steel n2.satin steel handle n3.corrosion resistant n4.rust resistant n5.stain resistant n6.can be sharpened by traditional sharpening stones n7.properly designed & balanced handles to reduce chances of “carpal tunnel syndrome” na ) in different sizes nhandle 10 11cm nshank 2.7 3.2cm nblade length 5.8 6.5mm, width 1.3 1.6mm, 90 degree offset angle nsemicircular cross section with convex base nb ) in sizes of sc4r / 4l6 nhandle 10 11cmshank 2.9 3.4 cm nblade length 5.8 6.5mm, width 1.3 1.6mm, n90 degree offset angle nsemicircular cross section with convex base. 269 university of michigan o probe n nspecification: n nfor use in periodontal surgery nsingle ended probe with markings at 3 6 8mm 270 upper canine extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 271 upper incisor extraction forcep english pattern n nspecification: n nforcep made of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 272 upper molar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint nset of one piece right & one piece left upper molar forcep 273 upper premolar extraction forcep english pattern n nspecification: n nmade of hard stainless steel with knurnled handle grip, disc / box type of hinge joint 274 upper roots forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip 275 upper universal forcep n nspecification: n nmade of hard stainless steel with knurnled handle grip 276 uv steriliser n nspecification: n ndimensions of cabinet: 22 x 12 x 8” nfront door with uv protected glass window & magnetic door seal nprovided with multiple tray racks not less than four nelectrically operated nprovided with uv light source 277 vacuum investment unit n nspecification: n ncapable of mixing unit amount of investment material under vacuum through a motor 278 vacuum mixing machine n nspecification: n n1. vacuum mixing machine nfor mixing investment material n2. electrically operated motor 1500 watts or more n3. compact n4. automatic regulation of the vacuum n5. the mixing motor remains clean and is easily serviced due to a supporting filter and a fine filter in conjunction with the maintenance free vacuum pump n6. direct connection between mixing bowl and vacuum pump – no disturbing exterior hose n7. mechanical coupling tolock the mixing bowl in position n8. a mixing bowls ( 500 g ) niso 13485 or ce certificate n 279 vibrator n nspecification: n n• electrically operated size 4.5 x 8 x 6.5 inches or moreplatform shaperectangular, type heavy duty n• constructionenamel painted body with rubber plate above body, speed: 3 speed vibration controller n• platform shaperectangular 280 warwick james elevators n nspecification: n nmade of hard stainless steel nset of 3 units right, left & straight tips 281 wax block storing cabinet n nspecification: n ncabinet made out of duro board, externally clad in laminated sheet. dust proof door is lockable. provided with smoothly sliding drawers with sixteen compartments each of size 4x4x2 and have puller knobs. each compartment can store blocks in two rows. 282 wax burnout furnace n nspecification: n nmaximum temp 1200c working temp 1150c with digital display cum temperature controller with safety alarm nmuffle size : 175x175x225mm n 4.0k.w 283 wax curver: pkt type n nspecification: n nset of 5 instruments n 284 wax knife n nspecification: n nmade of stainless steel nwith one end bearing knife pointed & other thick, flat with curved end 285 wax spatula n nspecification: n nmade of stainless steel nwith one end pointed & other end curved 286 weingart plier n nspecification: n ntungsten carbide tipped n 287 westcott curved tenotomy scissors n nspecification: n n19mm / 21mm made of stainless steel 288 who probe n nspecification: n na. clinical nb. epidemiological n na. clinical – 0.5 mm ball at the tip, making at 3.5mm, 8.5mm, 11.5 mm, colour coding 3.5 5.55 mm nweight – 5 gm nb. epidemiological marking at 3.5 mm & 5.5 mm n0.5 mm ball at the tip 289 williams probe n nspecification: n nfor use in periodontal surgeryth marking at 1, 2, 3, 5, 7, , 9 & 10mm 290 wire cutter n nspecification: n nmade of hard tempered steel n 291 wire tucker n nspecification: n nfor orthodontic work. tungsten carbide tipped 292 wooden / plastic slide boxes n nspecification: n nframework with finger joints fabricated out of teakwood with sunmica top and plywood bottom. wooden grooves for standing 3”x1” glass slide in vertical position individually. inside bottom covered with velvet and inside top with printed index. provided with brass chromium plated hinges clips and card frame. finished in natural color niro cellulose lacquer. 293 wooden mallet n nspecification: n nhaving wooden head that is10 cm in length, round at one end of diameter 3 cms while tapered at other end, handle length 28 cms nfor prosthodontic laboratory use 294 woodson periosteal elevator n nspecification: n ndouble ended one end curved ( curved working end length: 10 14 mm, width: 5 6mm ) nflat tapered end: length – 14 16 mm, width at the widest point 4 6 mm...