39525517 bids are invited for custom bid for services annual rate contract for maintenance servicing and calibration of thermogravimetric analyser tga model701 and automated bomb calorimeter modelac 500 make ms leco corporation for two 02 years at mtps dvc total quantity :...
39425350 bomb calorimeter (automatic) with digital display and data acquisition as per tender document...
39320968 tender for procurement of an automatic isoperibol bomb calorimeter (make leco/parr/ika)at chemical dept/dpps/dpl....
39314790 bids are invited for fully automatic microprocessor controlled bomb calorimeter ( q3 ) mse total quantity : 5...
38807847 repairing of bom calorimeter of kunustoria area laboratory. o ring, part no: 1583500, o ring, part no: 1583600, magnetic valve, part no: 3784400, slip coupling angled, part no: 3087100, o ring, part no: 1515200, pump, part no: 3190800, nut hexagon nut m4 934, part no: 2410800, nut hexagon nut m4 934, part no: 7045100, valve piston, part no: 7158400, set of valves, part no: 3851500, gas refilling and pcb repairing of chiller for bomb calorimeter...
38352143 supply and installation of ups with batteries for bomb calorimeter....
37580179 bids are invited for automatic bomb calorimeter (q3) total quantity : 1...
37565120 tender for procurement of bomb calorimeter & proximate analyser ( thermogravimetric analyser tga ) for sgtpp chemical laboratory under capex 2023 24 1 procurement of bomb calorimeter & proximate analyser ( thermogravimetric analyser tga ) for sgtpp chemical laboratory under capex 2023 24 2 automatic bomb calorimeter ( detail technical descriptions as per annexure ) 3 thermo gravimetric analyser for proximate analysis of coal ( detail technical descriptions as per annexure ) ...
36550161 tender for supply of the under mentioned goods or articles, bomb calorimeter....
36231758 bids are invited for bomb calorimeter total quantity : 1...
35931493 bids are invited for bomb calorimeter bomb calorimeter total quantity : 1...
35902233 bids are invited for isoperibol automated bomb calorimeter total quantity : 1...
35859455 bids are invited for bomb calorimeter mse cover large 5 per pkg , spindle drive , valve sol 3w vdc , pad foam oven bottom , blower assy 230v , crucible large tga glazed tga 5 per pk , mount resilient sq , tran 230v ncfm , crucible 10 per pkg spare parts of thermo gravimetric analyser and automated total quantity : 24...
35758703 bids are invited for bomb calorimeter (q3) total quantity : 1...
35578182 bids are invited for bomb calorimeter mse bomb calorimeter total quantity : 1...
35346007 calibration of laboratory equipment / items for use at sonepur bazari area laboratory. testing sieve ( 3.35 mm ) testing sieve ( 12.5 mm ) testing sieve ( 212 micron ) dry and wet bulb thermometer cap. ( ) 08 to 50° c 4 specific gravity hydrometer, range 1.000 2.000, sp. gr 5 glass thermometer, range ( ) 10° 250° c. 6 weight box, range 10mg to 100 gr. pipette, range 25 ml... 9 burette, range 50 ml. 10 measuring cylinder 500 ml 11 measuring cylinder 1000 ml 12 volumetric flask, cap 1000 ml 13 volumetric flask, cap 2000 ml 14 pressure gauge range 0 70 kgs. / cm2 15 digital temp. controller of muffle furnace, range 0 to 1000°. 16 v.m. furnace controller 0 to 1200° c. digital temp. controller of equilibration chamber range 17 18 hot air oven, range 0° 300° 19 hot air oven, range 0° 200° 20 21 digital balance, range 120 gm. digital balance, range 40 gm. to 80 kg 2 temp. ( digital ) indicator of bomb calorimeter, range 0 ohms to 100°. 1. j~ csty etc...
35089531 annual maintenance contract ( non comprehensive ) of bomb calorimeter at jhanjra area laboratory of eastern coalfields ltd....
35069098 annual maintenance contract ( non comprehensive ) of bomb calorimeter at jhanjra area laboratory of eastern coalfields ltd....
35013172 tender for spares of bomb calorimeter, lead wire ingniton ( pk of 2 ) , benzoic acid plts 100 g bottle , capsule holder , ingnition thread , o ring nbr , o ring nbr , o ring nbr , o ring ep 3 , nut , electrode t316 , 1 / 8 od tubing , tubing kit , ferrule set , nut 1 / 8 t , washer monel , 6 32 *1 / 4 rhms t316 , heat wire 60...
34963061 procurement of spares for bomb calorimeter....
34592612 bids are invited for bomb calorimeter bomb calorimeter total quantity : 1...
34503864 annual maintenance contract ( amc ) of ika equipment bomb calorimeter c2000 with chiller....
34492375 annual maintenance contract non comprehensive of bomb calorimeter at jhanjra area laboratory of eastern coalfields ltd....
34444085 annual maintenance contract ( non comprehensive ) of bomb calorimeter at jhanjra area laboratory of eastern coalfields ltd....
34361742 procurement of instrument / equipment for the department of geography, knu , equipments: , total station ( trimble c3 mechanical ) , differntial global positioning system ( dgps ) , core cutting and grinding machine , core drilling machine , point load index tester , bomb calorimeter ( automatic / semiautomatic, microprocessor based ) , automatic proximate analyser [ tga ] , muffle furnace , humidity chamber , primary jaw crusher , jaw crusher , double roller crusher , disc pulveriser with automatic feeding system , animal fossils , plant fossils...
33523661 domestic single e tender for procurement of spares and consumables of bomb calorimeter (make ika) under satgram area ...
33483211 procurement of spares and consumables of bomb calorimeter ( make ika ) under satgram area. 1. c6000 1 water project ( aqua pro ) 100 ml, part no.: 20014031 standard specification as per oem. 2. c 723 benzoic acid , blister package, 50 pc, part no.: 3243000 3. piston ( assy. ) , part no.: 3088000 4. pump, part no.: 3190800 5. connector, part no.: 39777100 6. o rings set, part no.: 1583500 7. magnetic valve, part no.: 3784400 8. sealing washer , part no.: 7159100 9. valve piston, part no.: 7158400 10. controller for chiller...
33085332 bids are invited for isoperibol automated bomb calorimeter (q3)mse total quantity : 1...
32887200 calibration work of laboratory equipment related works. i f1 weight box 2 test sieve ( 12.5 mm ) 3 test sieve 3 mm ) 4 test sieve ( 72 mesh ) 5 digital thermo hydrometer 6 : digital temperature indicator 7 digital balance ( 6000 grm. ) 8 digital balance ( 160 grm. ) 9 digital balance ( 220 grm. ) 10 digital temperature controller of muffle furnace 11 digital temperature controller of air oven 12 digital temperature controller of vni furnace 14 digital ph meter 15 i ) digital temp. indicator of bomb calorimeter. 16 pressure gauge ( heathit & pumping ) ...
32627631 e tender document for procurement of instrument/equipment for the department of mining engineering, knu 1. mechanical vane anemometer 2 rock triaxial cum unconfined compression testing machine 3 core cutting and grinding machine 4 core drilling machine 5 point load index tester 6 bomb calorimeter (automatic/ semiautomatic, microprocessor based) 7 automatic proximate analyser [tga] 8 muffle furnace 9 humidity chamber 10 primary jaw crusher 11 jaw crusher 12 double roller crusher 13 disc pulveriserwith automatic feeding system 14 animal fossils 15 plant fossils ...
32591819 procurement of instrument / equipment for the department of mining engineering, knu purchasing of equipment , equipments: , mechanical vane anemometer , rock triaxial cum unconfined compression testing machine , core cutting and grinding machine , core drilling machine , point load index tester , bomb calorimeter ( automatic / semiautomatic, microprocessor based ) , automatic proximate analyser [ tga ] , muffle furnace , humidity chamber , primary jaw crusher , jaw crusher , double roller crusher , disc pulveriser with automatic feeding system , animal fossils , plant fossils...
32236781 required comprehensive annual maintenance contract of bomb calorimeter...
32171837 spares for bomb calorimeter. 1. tubing kit, make – parr instruments. 2. capsule holder, 1136 / 1138, make – parr instruments. 3. nut, electrode t 316 (2/pk), make – parr instruments. 4. 1/8 od tubing, pressure; nylon (25 ft), make – parr instruments. 5. ferrule set, 1/8 t brass, make – parr instruments....
31982142 procurement of laboratory equipments 1 weston’s differential pulley block 2 rockwell hardness testing machine 3 brinell hardness testing machine 4 charpy &izod impact testing machine ( mechanical type ) 5 universal testing machine 6 torsion testing machine 7 center gauge 8 combination square set 9 dial indicators, ( metric standard ) 10 feeler gauge 11 gear tooth vernier caliper 12 inside micrometer 13 magnetic stand with fine adjustment 14 outside micrometer 15 outside vernier micrometer 16 precision spirit level 17 radius gauge 18 ring gauge 19 screw pitch gauge 20 sine bar 21 slip gauge, ( metric set ) 22 snap gauge 23 surface plate 24 universal bevel protractor 25 vernier caliper, ( metric / inch scale ) 26 vernier height gauge, ( metric / inch scale ) 27 120° v block with two clamp 28 optical flat with monochromatic light source 29 gear tooth micrometer ( analog ) – interchangeable ball anvil / spindle tip type 30 screw thread micrometers interchangeable anvil / spindle tip type 31 air conditioning tutor 32 bomb calorimeter with complete outfit 33 cut out model of room air conditioner 34 cut section model of fire tube cochran boiler 35 cut section model of lancashire boiler 36 cut section model of water tube babcock and wilcox boiler 37 cut section of model of actual hermetically sealed reciprocating compressor 38 refrigeration demonstration unit 39 separating & throttling steam calorimeter with boiler 40 thermal solar water heating system 41 stefan boltzmann’s apparatus 42 dead weight pressure gauge tester 43 apparatus to measure thermal conductivity of a solid metallic rod 44 shell and tube heat exchanger 45 heat exchanger parallel flow and counter flow type 46 single stage, single cylinder reciprocating compressor 47 cam analysis apparatus 48 cut section model ofsynchromesh gear box 4 forward speed & 1 reverse speed with single plate clutch 49 cut section model of constant mesh gear box 50 actual cut section model of differential gear box with rear axle assembly 51 static and dynamic balancing of rotating masses apparatus 52 universal governor apparatus 53 power transmitted by any belt drive using any one dynamometer 54 cut section model of single shoe brake 55 cut section model ofband brake 56 cut section model of plate clutch 57 cut section model of multi plate clutch 58 all geared lathemachine 59 universalmillingmachine 60 shaping machine 61 bench grinder machine 62 bench drilling machine 63 digital logic trainer board ( in build bread boards provision ) ( common for edc and dld lab ) 64 ic 65 7 segment led display 66 resistance 67 led 68 jumper wire 69 jumper wire cutter 70 twizzer 71 magnifying glass 72 function generator 73 diode trainer kit 74 transistor trainer kit 75 operational amplifier trainer kit 76 electronic trainer board ( in build bread boards provision ) ( common for edc and dld lab ) 77 555 timer in astable, monostable operation 78 discrete components resister 79 digital multimeter 80 discrete components capacitors 81 dual channel cro 30mhz 82 8086 trainer kit 83 unmanaged switch 84 hub 85 cat 5e / 6 cable 86 rj 45 connectors 87 rj 45 crimping tools 88 network lan cable tester ( rj 45 ) 89 access point ( wifi router / wireless router ) 90 ph meter 91 v notch 92 experimental set up for determination of frictional loss 93 jaw crusher 94 ball mill 95 plate & frame filter press 96 centrifuge 97 buckner funnel 98 centrifugal pump & gear pump 99 linear expansion of metal rod 100 double pipe heat exchanger 101 rotameter calibration equipment 102 thermocouples 103 control valve 104 thermostatic water bath 105 digital multimeter 106 open pan evaporator 107 hot air oven 108 muffle furnace 109 smoke point apparatus 110 softening point apparatus ( ring & ball ) 111 aniline point apparatus 112 astm distillation apparatus 113 conradson carbon residue apparatus 114 ramsbottom carbon residue apparatus 115 redwood viscometer no. i, 116 redwood viscometer no.ii 117 dean & stark apparatus ( glass apparatus ) 118 resin kettle & accessories 119 melting pointapparatus 120 surface tensiometer 121 thermostatic water bath 122 bubble cap distillation column 123 sieve plate distillation column 124 packed bed absorption column 125 vapour in air diffusion apparatus 126 natural draft tray dryer 127 forced draft tray dryer 128 packed bed liquid liquid extraction apparatus 129 spray tower for liquid extraction 130 solid liquid extraction ( bonnoto type ) 131 solid liquid extraction ( packed bed type ) 132 simple batch distillation column 133 wetted wall absorption column 134 batch crystallizer 135 vapour liquid equilibrium set up 136 experimental water cooling tower 137 humidification & dehumidification setup 138 packed bed reactor 139 plug flow tubluarreactor...
31596198 bids are invited for 1 uhplc with pda& fld detector 2 hplc with pda& ri detector 3 bomb calorimeter 4 bottle top dispenser 5 autotitrator 6 laboratory grinding mill 7 bod incubator 8 microwave muffle furnace 9 hot air oven 10 moisture analyser 11 muffle furnace 12 conductivity meter & turbidity meter 13 centrifugal vaccumconcentrator 14 cooling centrifuge benchtop 15 deep freezer mini product 80°c 16 ftir with atr & liquid cells 17 biosafety cabinet 18 multi tube vortex extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes. ( for anunlimited time ) average turn over of last 3 years 170 lakh ( s ) mse total quantity : 1...
31403262 procurement of lcd display & lcd transition for bomb calorimeter ( parr , usa make ) ....
31026297 bids are invited for procurement of auto bomb calorimeter (q3) total quantity : 1...
30258040 supply, installation and commissioning of equipments. machineries, tools etc. notice inviting e tender for procurement of machineries, implements, equipments, and tools etc. for murshidabad institute of technology. , concrete core cutter ( portable ) , blaine air permeability test apparatus for measuring fineness of cement , digital rebound hammer with calibraton anvil ( for concrete compressive strength analysis in the field and material hardness testing. ) , ductility testing apparatus , estimating software for like quepro 05 users , flash and fire point apparatus , liquid limit device, motorised , marshall apparatus ( electrically operated ) astm d 1559 , pycnometer for determination of specific gravity of sand and fine gravel , rebar locator ( metric scale hand held unit with charger in carrying case ) , ring and ball apparatus conform to is:1205 ( electrically operated ) , viscometer ( electrically heated ) as per is 1206 part ii astm d 88, e 102 , total station , cube mould ( 70.6 mm ) , digital theodolite , i.s. sieves [ for aggregate ( coarse and fine ) &soil ] , prismatic compass , ranging rod , manual compression testing machine , mould board plough , disc plough , self propelled paddy reaper , manually operated thresher , knapsack sprayer , power weeder , parabolic solar cooker , solar water heater , hydraulic tractor trolley , hydraulic jack , power sprayer , sieve shaker, motorised , aluminium air tight containers set , vacuum desiccator , hydrometer including all accessories , electronic weighing balance ( upto 0.01 gm accuracy ) , steel tape ( 30m ) , cross staff , offset rod , alidade , spirit level , dumpy level , plane table with accessories & tripod ( wooden ) , automatic level with box, stand and all standard accessories ( 32x or better ) , arrow , core cutter , cassagrande tools / astm tools , plastic limit apparatus , shrinkage limit apparatus , permeability test apparatus with accessories , horizontal centrifugal pump with motor , vertical centrifugal pump with motor , rotary gear pumps , submersible water pump , non recording rain gauge , rapid moisture meter , auger , refrigerator , laboratory cream separator ( disc bowl type ) , laboratory shell and tube heat exchanger ( water to water ) , laboratory plate heat exchanger ( water to water ) , hot air oven , electronic weighing balance , aluminium moisture box , desiccators , sling psychrometer , hygrometer , baking oven , lawn mower ( petrol engine ) , lab model grain / rice grader , tyre pressure gauge , tool box , conical flask ( 250 ml ) , beaker ( 100 ml ) , burette ( 50 ml ) , burette stand with clamp , bunsen burner with flame stabilizer , reagent bottle ( glass made, 250 ml ) , pipette ( 25 ml ) , apron , arsenic detection kit , volumetric flask ( 1 litre ) , volumetric flask ( 500 ml ) , volumetric flask ( 250 ml ) , measuring cylinder ( 10 ml ) , measuring cylinder ( 100 ml ) , centrifugal pump test rig to determine overall efficiency. , reciprocating pump test rig to determine overall efficiency. , tig welding machine, , actual cut section model of solex carburetor along with complete layout petrol fuel supply system, , simple screw jack, ( new ) , single plate coil spring type clutch , working model of clutch , hydraulic brake system , epicyclic gear train & holding torque apparatus , complete dynamometer set up for determination of power transmitted by any belt drive. , oil hydraulic circuit trainer unit , cut out model of gear pump , cut out model of vane pump , cut model of spool type direction control valve system. , cut model of rotary type direction control valve system. , experimental setup for measurement of flow of liquid using rotameter , experimental setup for measuring strain by using strain gauge, , experimental setup for temperature measurement & control using thermister, , digital tachometer , anemometer to measure velocity of compressible fluid across a duct. , bomb calorimeter with complete outfit, , solar water heating system, , apparatus to determine thermal conductivity of metal rod ( table top good quality apparatus ) , separating & throttling steam calorimeter with boiler, , indexing head , index plate , machine vice , air plasma cutting machine , electrode holder heavy duty , welding glass , welding goggles , second cut hand file , hackshaw frame , flat chisel , diamond point chisel , round file , half round file , flexible hand grinder , micro processor trainer kit ( 8085 ) ( lab instrument ) , soldering iron kit box , digital multimeter auto ranging with analogbargraph , screwdriver set ( kit box ) , micro processor tranner kit ( 8086 ) ( lab instrument ) , microcontroller tranner kit ( 8051 ) ( lab instrument ) , ic burner kit , d.c. network analyzer. , to simulate ac distributor , pyranometer , complete set up for directional over current relay: suitable for studying the characteristics and testing , relay test kit ( numerical relay testing kit ) , complete set up for idmtl type over current relay: suitable for studying the characteristics and testing. , complete set up for under voltage relay: suitable for studying the characteristics and testing. , complete set up for earth fault relay: suitable for studying the characteristics and testing , complete set up for transformer differential relay: suitable for studying the characteristics and testing , induction motor ( slip ring ) with suitable loading arrangement. , starter ( for ac motors ) : , synchronization of 3 phase alternator coupled with dc motor for parallel operation , study of active and reactive power flow control of an alternator , contact type digital tachomater , ammeter ( moving iron ) 0 2amp, sett & de or equivalent , ammeter ( moving iron ) 0 10amp, sett & de or equivalent , ammeter ( moving iron ) 0 20amp, sett & de or equivalent , ammeter ( moving coil, dc ) 0 10amp, 0 20amp sett & de or equivalent , digital multimeter, 3.5 digits display, data hold, overload, high frequency, capacitor, inductor measurement , voltmeter ( moving iron ) 0 10v / 20v, sett & de or equivalent , voltmeter ( moving iron ) 0 100v / 200v, sett & de or equivalent , voltmeter ( moving iron ) 0 500v, sett & de or equivalent , voltmeter ( moving coil, dc ) 0 250 / 500v, sett & de or equivalent , wattmeter ( electrodynamometer ) 0 50watt , wattmeter ( electrodynamometer ) 0 500watt , wattmeter ( electrodynamometer ) 0 2000watt , clip on ammeter , r l c series parallel circuit , testing kit for verification of maximum power transfer theorem , insulation testing by megger , kelvin double bridge kit , maxwell’s bridge for inductance , wein’s bridge for capacitance , shearing bridge for unknown capacitance , study of position control system ( dc ) kit , study of position control system ( ac ) of 2phase servomotor kit , dc series motor with belt pully arrangement kit , dc shunt motor with speed control arrangement kit , dc shunt motor with belt pully arrangement for load testing kit , dc shunt motor generator coupled set for no load and full load characterisitics kit , slip ring induction motor with suitable loading arrangement kit , parallel operation of single phase transformer , lux meter , optical bench method , trainer kit of inverse square law , sodium vapour lamp, mercury vapour lamp , slide calipas , digital slide calipas , screw gauge , specific gravity bottle , boyle’s law apparatus , glass slab , hydrostatic balance with weight box , optical bench , travelling microscope , stokes’ law apparatus , optical lens , regulated power supply , voltmeter , ammeter , galvanometer , resistance box , meter bridge , p.o box , scientific calculator , stop watch , digital multimeter 3 ½ digit multimeter with backlight , ncv, 1999 count, true rmsn torch function, hfe test , barometer , analog hg thermometer , resonance air column apparatus , bar magnet , metal bob ( solid sphere ) , wooden scale , p n junction diode characteristic apparatus , battery case , ohm s law apparatus...
30125337 bids are invited for uhplc with pda& fld detector uhplc with pda& fld detector , hplc with pda& ri detector hplc with pda& ri detector , bomb calorimeter bomb calorimeter , bottle top dispenser bottle top dispenser , autotitrator autotitrator , laboratory grinding mill laboratory grinding mill , bod incubator bod incubator , microwave muffle furnace microwave muffle furnace , hot air oven hot air oven , moisture analyser moisture analyser , muffle furnace muffle furnace , conductivity meter & turbidity meter conductivity meter & turbidity meter , centrifugal vaccumconcentrator centrifugal vaccumconcentrator , cooling centrifuge benchtop cooling centrifuge benchtop , deep freezer mini product 80°c deep freezer mini product 80°c , ftir with atr & liquid cells ftir with atr & liquid cells , biosafety cabinet biosafety cabinet , multi tube vortex multi tube vortex total quantity : 1...
30116574 bids are invited for uhplc with pda& fld detector uhplc with pda& fld detector , hplc with pda& ri detector hplc with pda& ri detector , bomb calorimeter bomb calorimeter , bottle top dispenser bottle top dispenser , autotitrator autotitrator , laboratory grinding mill laboratory grinding mill , bod incubator bod incubator , microwave muffle furnace microwave muffle furnace , hot air oven hot air oven , moisture analyser moisture analyser , muffle furnace muffle furnace , conductivity meter & turbidity meter conductivity meter & turbidity meter , centrifugal vaccumconcentrator centrifugal vaccumconcentrator , cooling centrifuge benchtop cooling centrifuge benchtop , deep freezer mini product 80°c deep freezer mini product 80°c , ftir with atr & liquid cells ftir with atr & liquid cells , biosafety cabinet biosafety cabinet , multi tube vortex multi tube vortex total quantity : 1...
29757982 bids are invited for fully automatic microprocessor controlled bomb calorimeter (q3) () total quantity : 5...
29637543 replacing of false ceiling at bomb calorimeter and gas analysis room of laboratory under jhanjra area....
29588492 replacing of false ceiling at bomb calorimeter and gas analysis room of laboratory under jhanjra area....
29545413 instruments , 2 blast freezer 3 cmos camera with computing & printing for existing inverted microscope 4 colorimeter for measurement of pigments 5 digital hot plate 6 electronic balance 7 feed analyzer with computing and printing 8 feed pelletizer 9 interacting duel display touch screen kiosk information system with installation for displaying scientific information on the fishes 10 laboratory spray dryer 11 lamps for atomic absorption spectrophotometer ( varian make ) 12 lyophilizer ( freeze dryer ) 13 microprocessor based isoperibol automatic bomb calorimeter 14 refrigerated centrifuge 15 serological water bath 16 single chamber hematology analyzer 17 upright fluorescent microscope with photomicrography and image analysis software 18 vortexshaker 19 vortex mixer 20 vacuum packaging machine...
29539502 procurement of oxygen gas (industrial) of 1260 procurement of oxygen gas (industrial) of 1260 nm3 for thermo gravimetric analyzer (tga 701) and automated bomb calorimeter (ac 500) for two years for chemical laboratory (u 1 8), mtps, dvc , ...
29505582 supply, installation and demonstration of different equipments, instruments, trainer kits, models, study setups etc. for different laboratories of renewable engineering department of basirhat government polytechnic, bhyabla,basirhat, north 24 pgs supply, installation and demonstration of different equipments, instruments, trainer kits, models, study setups etc. for different laboratories of renewable engineering department of basirhat government polytechnic, bhyabla,basirhat, north 24 pgs , setup to plot current – voltage (i v) characteristics of single crystalline silicon solar cell , setup to plotcurrent – voltage (i v) characteristics of poly crystalline silicon solar cell and find out the following to study – i) the solar cell parameters – o.c. voltage (voc), short circuit current (isc), voltage current power at maximum power point (vmp, imp, mpp), fill factor, efficiency. , study the effect of shading on parameters of solar cell connected in series parallel combination. , study the effect of tilt angle on solar cell parameters (voc, isc, vmp, imp, mpp, fill factor, efficiency) , assemble and dismantle the solar pv system. , set up for performance analysis of single phase bridge inverter with r l load and voltage control by single pulse width modulation. , study of solar smart metering system and its troubleshooting. , experiment to run water pumping system using solar power. , solar street lighting system for dc supply. , identify different components of solar street lighting system for ac supply. , assemble the components of solar home lighting system & study the system. , setup to measure beam, diffuse and global radiation on horizontal and tilted surface using pyranometer and plot radiation vs. time characteristics for certain duration. , datalogger , multimeter , setup for characterization of a solar flat plate collector and evaluate its parameters. , setup for characterization of evacuated tube collector and evaluate its parameters. , setup for characterization of a solar concentrating collector and evaluate its parameters. , setup to measure thermal performance of a solar cooker with varying reflector. , setup to measure the parameters of a solar dryer. , setup to plot and analyse the characteristics curve of strain gauge. , setupto plot and analyse the characteristics curve of lvdt with distance as input. , setupto plot the load cell characteristics using different load as input. , setup to measure level of a tank using gauge glass, differential pressure transmitter. , setupto measure level of a tank using displacer, ultrasonic level meter. , setup to measure the flow of liquid using rotameter, and differential pressure transmitter. , setup to measure the temperature using pt100 and thermocouple. , identification of different parts of c type burdon tube pressure gauge. , study of operation of dead weight tester and calibration of pressure gauge using it. , study & measure calorific value of solid fuel using bomb calorimeter. , study of different parts of water turbines such as pelton wheel, francics and kaplan. , study of schematic layout of a hydroelectric power plant. , study of different parts of vane pump / gear pump generally used in hydraulic system. , study the different parts of a hydraulic trainer system. , setup to determine brake power, indicated power, efficiencies of four stroke cycle diesel engine. , identify the different parts of a dc machine and make a report on it. , setupfor speed control of a dc shunt motor below and above its rated speed. , identify the different parts of a single phase transformer and a three phase transformer (from a slide if machine is not available) & make a report on it. , identify the different parts of a 3 phase induction motor and make a report on it. , setup for no load test and blocked rotor test of a 3 phase induction motor & determine equivalent circuit parameters. , 3 phase, 5kva, 415v variac , setupto plot the o.c.c. of an alternator & observe the effect of excitation and speed on induced e.m.f.ii) perform experiment to find the percentage regulation of 3 phase alternator by synchronous impedance method at various power factor and load. , setupto synchronise two 3 phase alternators by – a) three lamp method orb) synchroscope and to study the sharing of load between the alternators. , identify different parts of permanent magnet synchronous generator (pmsg) and make a report on it. , identify the different parts of an – a) electromagnetic energy meter, b) electronic energy meter make a report on it. , setup to calibrate single phase energy meter using resistive or inductive loads. , setupto measure energy of 3 phase balanced load using electronic energy meter. , setup to measure 3 phase power of balanced 3 phase load by 2 wattmeter method. , setupto measure current ratio, voltage ratio and polarity test of ct and pt. , set up a small wind turbine (swt) system and identify its specified components. , setup to test the performance of squirrel cage induction generator (scig) – measurement of active and reactive power with respect to speed of scig and its analysis. , setupto test the performance of permanent magnet synchronous generator (pmsg) – a) no load test, b) load test. , set up of a anaerobic digestion biogas plant toi) measure the calorific value of the biogas.ii) measure the yield of the biogas changing the input parameters e.g. temperature, input raw materials.iii) calculate the efficiency of the biogas plant.iv) set up of a gas cleaning system with h2s and h2o filter. , study the construction and operation of energy efficient lamps – cfl, led, fluorescent lamp. , setupto calculate power and energy consumed by a florescent lamp using electronic ballast and magnetic ballast. , setupto compare lighting energy consumption of a model room using only artificial lighting and artificial lighting integrated with natural daylighting. , study the parts of a – i) lead acid battery and experiment for charging & discharging characterization of the battery and measure its parameters. , study the parts of a ni cd battery and experiment for charging & discharging characterization of the battery and measure its parameters. , study the parts of a li ion battery and experiment for charging & discharging characterization of the battery and measure its parameters. , setupconnect lead acid batteries in different connections to verify its voltage & ampere hour....
29101821 bas/etender/2021/135 supply, installation and demonstration of different equipments, instruments, trainer kits, models, study setups etc. for different laboratories of renewable engineering department of basirhat government polytechnic, bhyabla,basirhat, north 24 pgs , setup to plot current – voltage (i v) characteristics of single crystalline silicon solar cell , setup to plotcurrent – voltage (i v) characteristics of poly crystalline silicon solar cell and find out the following to study – i) the solar cell parameters – o.c. voltage (voc), short circuit current (isc), voltage current power at maximum power point (vmp, imp, mpp), fill factor, efficiency. , study the effect of shading on parameters of solar cell connected in series parallel combination. , study the effect of tilt angle on solar cell parameters (voc, isc, vmp, imp, mpp, fill factor, efficiency) , assemble and dismantle the solar pv system. , set up for performance analysis of single phase bridge inverter with r l load and voltage control by single pulse width modulation. , study of solar smart metering system and its troubleshooting. , experiment to run water pumping system using solar power. , solar street lighting system for dc supply. , identify different components of solar street lighting system for ac supply. , assemble the components of solar home lighting system & study the system. , setup to measure beam, diffuse and global radiation on horizontal and tilted surface using pyranometer and plot radiation vs. time characteristics for certain duration. , datalogger , multimeter , setup for characterization of a solar flat plate collector and evaluate its parameters. , setup for characterization of evacuated tube collector and evaluate its parameters. , setup for characterization of a solar concentrating collector and evaluate its parameters. , setup to measure thermal performance of a solar cooker with varying reflector. , setup to measure the parameters of a solar dryer. , setup to plot and analyse the characteristics curve of strain gauge. , setupto plot and analyse the characteristics curve of lvdt with distance as input. , setupto plot the load cell characteristics using different load as input. , setup to measure level of a tank using gauge glass, differential pressure transmitter. , setupto measure level of a tank using displacer, ultrasonic level meter. , setup to measure the flow of liquid using rotameter, and differential pressure transmitter. , setup to measure the temperature using pt100 and thermocouple. , identification of different parts of c type burdon tube pressure gauge. , study of operation of dead weight tester and calibration of pressure gauge using it. , study & measure calorific value of solid fuel using bomb calorimeter. , study of different parts of water turbines such as pelton wheel, francics and kaplan. , study of schematic layout of a hydroelectric power plant. , study of different parts of vane pump / gear pump generally used in hydraulic system. , study the different parts of a hydraulic trainer system. , setup to determine brake power, indicated power, efficiencies of four stroke cycle diesel engine. , identify the different parts of a dc machine and make a report on it. , setupfor speed control of a dc shunt motor below and above its rated speed. , identify the different parts of a single phase transformer and a three phase transformer (from a slide if machine is not available) & make a report on it. , identify the different parts of a 3 phase induction motor and make a report on it. , setup for no load test and blocked rotor test of a 3 phase induction motor & determine equivalent circuit parameters. , 3 phase, 5kva, 415v variac , setupto plot the o.c.c. of an alternator & observe the effect of excitation and speed on induced e.m.f.ii) perform experiment to find the percentage regulation of 3 phase alternator by synchronous impedance method at various power factor and load. , setupto synchronise two 3 phase alternators by – a) three lamp method orb) synchroscope and to study the sharing of load between the alternators. , identify different parts of permanent magnet synchronous generator (pmsg) and make a report on it. , identify the different parts of an – a) electromagnetic energy meter, b) electronic energy meter make a report on it. , setup to calibrate single phase energy meter using resistive or inductive loads. , setupto measure energy of 3 phase balanced load using electronic energy meter. , setup to measure 3 phase power of balanced 3 phase load by 2 wattmeter method. , setupto measure current ratio, voltage ratio and polarity test of ct and pt. , set up a small wind turbine (swt) system and identify its specified components. , setup to test the performance of squirrel cage induction generator (scig) – measurement of active and reactive power with respect to speed of scig and its analysis. , setupto test the performance of permanent magnet synchronous generator (pmsg) – a) no load test, b) load test. , set up of a anaerobic digestion biogas plant toi) measure the calorific value of the biogas.ii) measure the yield of the biogas changing the input parameters e.g. temperature, input raw materials.iii) calculate the efficiency of the biogas plant.iv) set up of a gas cleaning system with h2s and h2o filter. , study the construction and operation of energy efficient lamps – cfl, led, fluorescent lamp. , setupto calculate power and energy consumed by a florescent lamp using electronic ballast and magnetic ballast. , setupto compare lighting energy consumption of a model room using only artificial lighting and artificial lighting integrated with natural daylighting. , study the parts of a – i) lead acid battery and experiment for charging & discharging characterization of the battery and measure its parameters. , study the parts of a ni cd battery and experiment for charging & discharging characterization of the battery and measure its parameters. , study the parts of a li ion battery and experiment for charging & discharging characterization of the battery and measure its parameters. , setupconnect lead acid batteries in different connections to verify its voltage & ampere hour....
29095095 supply, installation and demonstration of different equipments, instruments, trainer kits, models, study setups etc. for different laboratories of renewable energy department of canning government polytechnic, canning, south 24 pgs, setup to plot current – voltage ( i v ) characteristics of single crystalline silicon solar cell , setup to plotcurrent – voltage ( i v ) characteristics of poly crystalline silicon solar cell and find out the following to study – i ) the solar cell parameters – o.c. voltage ( voc ) , short circuit current ( isc ) , voltage current power at maximum power point ( vmp, imp, mpp ) , fill factor, efficiency. , study the effect of shading on parameters of solar cell connected in series parallel combination. , study the effect of tilt angle on solar cell parameters ( voc, isc, vmp, imp, mpp, fill factor, efficiency ) , assemble and dismantle the solar pv system. , set up for performance analysis of single phase bridge inverter with r l load and voltage control by single pulse width modulation. , study of solar smart metering system and its troubleshooting. , experiment to run water pumping system using solar power. , solar street lighting system for dc supply. , identify different components of solar street lighting system for ac supply. , assemble the components of solar home lighting system & study the system. , setup to measure beam, diffuse and global radiation on horizontal and tilted surface using pyranometer and plot radiation vs. time characteristics for certain duration. , datalogger , multimeter , setup for characterization of a solar flat plate collector and evaluate its parameters. , setup for characterization of evacuated tube collector and evaluate its parameters. , setup for characterization of a solar concentrating collector and evaluate its parameters. , setup to measure thermal performance of a solar cooker with varying reflector. , setup to measure the parameters of a solar dryer. , setup to plot and analyse the characteristics curve of strain gauge. , setupto plot and analyse the characteristics curve of lvdt with distance as input. , setupto plot the load cell characteristics using different load as input. , setup to measure level of a tank using gauge glass, differential pressure transmitter. , setupto measure level of a tank using displacer, ultrasonic level meter. , setup to measure the flow of liquid using rotameter, and differential pressure transmitter. , setup to measure the temperature using pt100 and thermocouple. , identification of different parts of c type burdon tube pressure gauge. , study of operation of dead weight tester and calibration of pressure gauge using it. , study & measure calorific value of solid fuel using bomb calorimeter. , study of different parts of water turbines such as pelton wheel, francics and kaplan. , study of schematic layout of a hydroelectric power plant. , study of different parts of vane pump / gear pump generally used in hydraulic system. , study the different parts of a hydraulic trainer system. , setup to determine brake power, indicated power, efficiencies of four stroke cycle diesel engine. , identify the different parts of a dc machine and make a report on it. , setupfor speed control of a dc shunt motor below and above its rated speed. , identify the different parts of a single phase transformer and a three phase transformer ( from a slide if machine is not available ) & make a report on it. , identify the different parts of a 3 phase induction motor and make a report on it. , setup for no load test and blocked rotor test of a 3 phase induction motor & determine equivalent circuit parameters. , 3 phase, 5kva, 415v variac , setupto plot the o.c.c. of an alternator & observe the effect of excitation and speed on induced e.m.f.ii ) perform experiment to find the percentage regulation of 3 phase alternator by synchronous impedance method at various power factor and load. , setupto synchronise two 3 phase alternators by – a ) three lamp method orb ) synchroscope and to study the sharing of load between the alternators. , identify different parts of permanent magnet synchronous generator ( pmsg ) and make a report on it. , identify the different parts of an – a ) electromagnetic energy meter, b ) electronic energy meter make a report on it. , setup to calibrate single phase energy meter using resistive or inductive loads. , setupto measure energy of 3 phase balanced load using electronic energy meter. , setup to measure 3 phase power of balanced 3 phase load by 2 wattmeter method. , setupto measure current ratio, voltage ratio and polarity test of ct and pt. , set up a small wind turbine ( swt ) system and identify its specified components. , setup to test the performance of squirrel cage induction generator ( scig ) – measurement of active and reactive power with respect to speed of scig and its analysis. , setupto test the performance of permanent magnet synchronous generator ( pmsg ) – a ) no load test, b ) load test. , set up of a anaerobic digestion biogas plant toi ) measure the calorific value of the biogas.ii ) measure the yield of the biogas changing the input parameters e.g. temperature, input raw materials.iii ) calculate the efficiency of the biogas plant.iv ) set up of a gas cleaning system with h2s and h2o filter. , study the construction and operation of energy efficient lamps – cfl, led, fluorescent lamp. , setupto calculate power and energy consumed by a florescent lamp using electronic ballast and magnetic ballast. , setupto compare lighting energy consumption of a model room using only artificial lighting and artificial lighting integrated with natural daylighting. , study the parts of a – i ) lead acid battery and experiment for charging & discharging characterization of the battery and measure its parameters. , study the parts of a ni cd battery and experiment for charging & discharging characterization of the battery and measure its parameters. , study the parts of a li ion battery and experiment for charging & discharging characterization of the battery and measure its parameters. , setupconnect lead acid batteries in different connections to verify its voltage & ampere hour....
29048526 wbtet / dtet / klm / nit 1 / 2021 e tender for procurement of equipments, instruments, machineries, tools etc. related to laboratories of civil engineering, mechanical engineering, electronics and telecommunication engineering departments of kalimpong govt. polytechnic, kalimpong, di , c.e. lab. items , air permeability apparatus ( blaine type ) : , sieve: of brass frame 20cm dia x 90 micron [ bis:460 part i & ii 1985, reaffirmed2008 ] , vicat apparatus with isi certification mark is:5513:1976 or latest fitted in aluminium box ( is 1727, 2541 ( p.1 ) , 2645, 4031 ) , vibrating machine is:10080 1982 , motorized compression testing machine, capacity 2000kn, digital [ conform is – 14858 ( 2000 ) ] with nccbm certified load gauge. with nabl / nccbm certificate , le chatelier mould with isi certification mark is:5514 reaffirmed 2011: , le chatelier water bath: , autoclave, with analogue pressure gauge & temp controller as per is: 4031 ( part 3 ) . , graduated measuring cylinder: of transparent material ( glass – make borosil ) , sieve shaker, motorised , pycnometer with necessary attachment as per relevant is code , aggregate impact test apparatus with counter , los angeles abrasion testing machine: ( is: 10070 1982 ) [ test procedure as in 2386 part iv reaffirmed in 2011 ] ( with counter ) , density basket is : 2386 ( part iii ) – 196 , electronic digital balance ( 25kg / 1g ) , electronic digital balance ( 20kg / 1g ) , bouyancy balance , standard pycnometer of capacity one litre and weighing balance of capacity 2 kg or more and accurate to0.5 g , slump test apparatus is: 7320 1974 , compaction factor apparatusis: 5515 1983 , vee bee consistometer is : 10510 1983 , flow table ( as per is: 5512 ) : , digital rebound hammer with calibration anvil , ultrasonic pulse velocity apparatus: , ring and ball apparatusis: 1205, ip:58 / 63 , pensky martens flash point ( closed ) tester ( electrically operated ) is: 1448 ( part 1 ) 1209, ip 34 / 58, , cloveland flash ( open ) and fire point apparatus [ electrically heated ] is: 1448 p:69 ip 36 / 63 , ductility testing machineis: 1208 1978 , viscometer ( electrically heated ) as per is 1206 part ii astm d 88, e 102 , marshall apparatus ( electrically operated ) astm d 1559 supplied complete with proving ring ( 30 kn capacity ) & dial gauge ( least count 0.002 mm, provided with calibration certificate as per is: 4169 ) . , digital mastic asphalt hardness tester, 0.01 mm , universal testing machinecapacity, 1000 kn , tile flexural strength testing machine ( ref standard is: 654, 1237 1980 ) . , total station , tile abrasion testing machine ( ref standard is:1237 1980, 1706 1972 ) , equipment for study of venturimeter , rapid moisture meter conforming to is: 12175 , hot air oven , flash and fire point apparatus , sand replacement apparatus [ small ] , plastic limit apparatus conforming to is: 2720 ( part v ) , shrinkage limit apparatus ( supplied with requisite quantity of mercury ) withthe apparatus conforms to is: 10077, and the test is performed as per is: 2720 ( part vi ) . , i.s. sieves [ for aggregate ( coarse and fine ) & soil ] , hydrometer [ as per is:2720 ( part iv ) ] , cut section model of reaction turbine , direct shear apparatus, 12 speed, motorised is: 2720 ( part xiii ) is: 11229 , laboratory vane shear apparatus ( motorized ) , prismatic compass , proctor compaction test ( standard ) bis: 2720 part 7 1974 standard: , triaxial test apparatus bis: 2720 – part 11 ( 1971 ) , part 12 ( 1981 ) , part 35 ( 1974 ) , , triaxial cell , circular ranging rod , spectrophotometer , turbidimeter , flocculator ( jar test apparatus , universal extractor frame ( manually operated ) , non corrodible air tight moisture can, made of aluminium, number engravedat lid and container body , liquid limit device, motorised , cube moulds mould, m. steel, for 70.6mm cube as per is: 10080 1982 , cube mould ( 150mm ) with i.s.i markas per is:10086 1982 , desiccator complete with desiccator plate ( glass ) 300 mm dia , experimental setup for measurement of speed of a shaft by stroboscope, , apparatus for determining radius of rotation of a porter governor at different speed of an engine , portable conductivity / resistivity / salinity / tds meter t , portable ph meter , automatic soil compaction machine as per i.s. : 2720 ( part vii & viii ) , length gauge conforms to is:2386 ( part i ) , thickness gauge conforms to is 2386 ( part i ) , survey umbrella , standard vernier theodolite with erect image, optical plummet alongwith aluminium stand , electrical table saw small , 200 amp igbt arc welding machine dc inverter , classic arc 300 two phase and three phase amps mosfet welding , e.t.c.e. lab. items , 30 mhz dual channel cro. , function generator , digital multimeter , 50 mhz dual trace cro , variable dcpower supply dual supply , 0v to 30v , 2a ; ±3 to ±15v , 1a;5v, 5a fixed, digital display. , diode characteristics trainer kit , bjt characteristic trainer kit , class b push pull amplifier trainer , to study the fet characteristics trainer , rc coupled amplifier circuit trainer , mosfet characteristics trainer kit , power electronics trainer kit { to study various components ujt, diac, triac, power mosfet, powed diode and power bjt ) , power factor meter ( single phase ) , crystal oscillator study , tuned amplifier trainer , complete setup to design / construct programmable up / down counter. , op amp trainer kit ( ic 741 based ) , multivibrator using ic555 timer trainer , multi o / p programmable linear dc power supply 32 v / 3 a, 32v / 3 a, 3.3v / 5a fixed, , digital logic trainer kit ( to verify the truth table of not, or, and, nand, nor, xor, x nor with ttl logic gates and cmos logic gates ) . , complete setup to implement encoder, decoder , multiplexer andde multiplexer. , experimental setup to design ofuniversal shift register , complete setup to design / construct parity generator, checker and comparator. , adc and dac trainer kit , digital flip flop trainer kit , binary synchronous and asynchronous counter trainer , network and bridges trainer kit , digital i.c tester , series and parallelresonant circuit trainer , a kit of basic electricity & electronics components , passive filter trainer , t and pi network trainer kit , training kit tostudy of linear series and shunt regulator , single phase transformer by performing ( i ) o.c. test ( ii ) s.c. test. , study of three point and four point starter , 8085microprocessor traineer kit , microprocessor 8086 trainer kit , to study the amplitude modulation and demodulation ttrainer kit , am / fm radio receiver kit , analog signal sampling & reconstruction trainer kit , dsb / ssb amtransmitter / receiver trainer. , frequency modulation anddemodulation trainer kit , delta / sigma delta and adaptive delta modulation demodulation kit , dpcm & adpcm modulation / demodulation kit dpcm & adpcm modulation / demodulation kit , epbax trainer kit , digital communication trainer , dth tv and set top box trainer kit , colour tv trainer with provision of fault finding , tdm and pcm modulation / demodulation trainer kit , digital storage oscilloscope , microwave test bench ( klystronbased ) , ask / psk / fsk modulation and demodulation kit , satellite communication trainer , 1.5 ghz spectrum analyser , antenna trainer kit , training kit to study chopper using scr , speed control of induction motor ( frequency changing with required panel & drive ) . , to study drive circuit of scr , frequency counter , to study smps with pwm regulator chip , ac servo voltage stabilizer as servo mechanism , jones chopper trainer , different starters for induction motor , to study the speed control of dc motor , stepper motor study set , single phase bridge inverter , pc based plc trainer , 1 kva online ups trainer kit , analog lab trainer kit , pc based optical fibercommunication kit , pam ppm pwm modulation and demodulation trainer , lcrq meter , 3ghz digital spectrum analyzer. , microcontroller ( 8051 ) trainer kit , lan trainer with protocol simulation and analysis software , pid controller trainer kit ( microprocessor based ) , gsm mobile telephone trainer , bread board , sholdering and desholdering kit , strain gauge trainer , measurement of temperature using thermocouple, rtd, thermistor, ad950 , to measure displacement with lvdt , collpitts oscillator & hartley oscillator trainer kit , training kit to study of rc phase shift oscillator , experimantal kit fowien bridge oscillator , m.e. lab. items , center gauge , combination square set , dial indicators, ( metric standard ) , dial bore gauge with dial indicator , feeler gauge , gear tooth vernier caliper , inside micrometer , outside micrometer , precision spirit level , radius gauge , ring gauge: , screw pitch gauge: , sine bar ( is : 5359 1987 ) : , slip gauge set ( metric set ) , dial snap gage: , surface plate: granite top surface plates with safety frame and with caster , universal bevel protractor with magnifier lens , vernier caliper ( metric / inch scale ) , vernier height gauge ( metric / inch scale ) , actual cut section working model of water tube babcocck and willcox boiler , cam analysis apparatus , actual cut section working model 4 speed sliding mesh gear box , actual cut section working model of constant mesh gear box , actual cut section working model of rear axle assembly of a 4 wheeler vehicle , static and dynamic balancing of rotating masses apparatus , universal governor apparatus , model of watt governor and porter governor , single shoe brake – working model , band brake – working model , single plate clutch – working model , model of cone clutch , model of centrifugal clutch , flywheel model , multiplate clutch – working model , actual cut section model of torque converter , bomb calorimeter with complete outfit, , cut section model of fire tube cochran boiler , cut section model of lancashire boiler, , cut section model of water tube babcock and wilcox boiler , horizontal & inclined plane friction slide apparatus , separating & throttling steam calorimeter with boiler , thermal solar water heating system , stefan boltzmann?s apparatus, , cut out model of lobe type compressor , actual cut section model of air brake system , double purchase crab winch , worm & worm wheel , rockwell hardness testing machine , rockwell hardness cone , ball indentors for rockwell testing m / c , brinell hardness testing machine , charpy & izod impact testing machine ( mechanical type ) , test piece: 1. rockwell, 2. brinell 3. izod 4. charpy 5. tensile, 6. torsion...
28887031 supply and installation of equipment for department of chemistry , chemistry , electronic balance ( three digit ) model no practum 213 10in make sartorius ag, germany , digital polari meter make ei , magnetic stair with hot plat , vacuum pump , mechanical shaker ( 16 flask capacity ) , boiling point apparatus ( digital ) , water bath ( 6 whole digital panel & temperature control ) , distillation plant ( 5 lit ) , hot incubator with digital panel , ice maker machine , chiller ( inkon , double beam uv vis spectrophotometer , electric centrifugal machines , uv cabinet , bomb calorimeter with digital firing unit , convection microwave oven , digital photo colorimeter , conductivity meter digital , digital potentiometer with electrode , ph meter digital , melting point apparatus ( digital ) ...