Military Engineer Services - West Bengal

39843103 tender for spl repair to bldg no. p 95 ( or md accn ) at lebong under age ( i ) darjeeling.; 1 dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings, complete all as specified and directed. 2 s&f of pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed. 3 s&f of pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed. 4 add to item 2.00 & 3.00 here in before if fixed with l type or j type or cranked hook bolts in lieu of screw, complete all as specified and directed. 5 dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. 6 s&f of mild steel hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding inconcrete and screwing etc. wind ties for roof including securing bolts conforming to fe 290 gde e 165, complete all as specified and directed 7 s&f of framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to fe.290.gde e 165 ( brackets over 10 kg each to be measured under structural steel ) , complete all as specified and directed. 8 roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., complete all as specified and directed. 9 m&l for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar ( 1:6 ) finished even and rough, complete all as specified and directed. 10 m&l for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles, complete all as specified and directed. 11 m&l for non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles, complete all as specified and directed. 12 m&l for machine cut kota stone slab 20 25mm thickin riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed. 13 m&l for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigments, complete all as specified and directed. 14 m&l for rendering 10mm thick in cement mortar ( 1:3 ) on fair faces of brick work or concrete surfaces, complete all as specified and directed. 15 m&l for coloured glazed ceramic tiles in vertical surface 350x 250x 7 mm / 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface of tiles, complete all as specified and directed. 16 taking down cement or cement lime plaster, any description on brick or stone masonrysurfaces of walls etc includingrakingout joints, hackingfor key, scrubbingdown with wateretc, complete all as specified and directed. 17 m&l for rendering 15mm thick in cement mortar ( 1:6 ) on fair faces of brick work or concrete surfaces, finished even and smooth ( without using extra lime or cement ) , complete all as specified and directed. 18 m&l for rendering 15mm thick in cement mortar ( 1:4 ) with water proofing compound @ 3% by weight of cement or in the manner specified by the manufacturer and in the proportions indicated on fair faces of brick work or concrete surfaces, finished even and smooth ( without using extra lime or cement ) , complete all as specified and directed.note: water proofing compound will be measured and paid separately. 19 m&l for 5mm thick rendering in cement mortar ( 1:3 ) on concrete surfaces in ceilings and finished even and smooth ( without using extra lime or cement ) , complete all as specified and directed. 20 supply only integral water proofing compond, all as specified and as directed. 21 m&l for preparation of new plastered or unplastered surface of wall and applying two coats of distemper oil emulsion ( obd ) , over acoat of priming coat ( chalk whiting, on plastered surfaces, prepara tory to distempering ) including 3mm thick wall care putty on wall, complete all as specified and directed. 22 m&l forpreparation of new plastered or unplastered surface of ceiling and applying one coat of oil bound distemper ( distemper oil emulsion ) over a coat of priming coat ( chalk whiting, on plastered surfaces, preparatory to distempering ) including 1mm thick wall care putty on ceiling, complete all as specified and directed. 23 m&l forpreparation of new plastered or unplastered surface of wall and finishing walls with acrylic smooth exterior paint of required shade : new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) , complete all as specified and directed. 24 m&l for complete removal of existing treatment on plastered or unplastered surface of wall including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying one coat 1mm thick of wall care putty and then applying two coats of distemper oil emulsion ( obd ) , white or tinted over a coat of priming coat ( chalk whiting, on plastered surfaces, preparatory to distempering ) after preparation of wall surfaces, complete all as specified and directed. 25 m&l for complete removal of existing treatment on plastered or unplastered surface of ceiling including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying one coat of oil bound distemper ( distemper oil emulsion ) over acoat of priming coat ( chalk whiting, on plastered surfaces, preparatory to distempering ) including 1mm thick layer of wall care putty on ceiling after preparation of wall surfaces, complete all as specified and directed. 26 m&l for complete removal of existing treatment on plastered or unplastered surface of wall including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces, complete all as specified and directed. 27 m&l for preparation of old decorated plastered or unplastered surfaces of wall including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying and applying two coats of white wash on walls, complete all as specified and directed. 28 m&l for preparation of old wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed. 29 m&l for preparation of new wooden or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. 30 m&l for preparation of old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed. 31 m&l for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed. 32 taking up or downold 15 mm bore steel water tubing and connections, including cleaning for refixing or removal to store or from site, complete all as specified and directed. 33 taking up or down old 20 mm bore steel water tubing and connections, including cleaning for refixing or removal to store or from site, complete all as specified and directed. 34 s&f of 15 mm bore steel water tubes, medium grade, galvanised with and including all gi fitting ( such as bends, elbows, tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceilingor laid in / on floor, complete all as specified and directed. 35 s&f of 20 mm bore steel water tubes, medium grade, galvanised with and including all gi fitting ( such as bends, elbows, tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceilingor laid in / on floor, complete all as specified and directed. 36 refixing old 15 mm bore steel tubing and connections in new or old position ( walls, ceiling, floors, etc. ) , complete all as specified and directed. 37 refixing old 20 mm bore steel tubing and connections in new or old position ( walls, ceiling, floors, etc. ) , complete all as specified and directed. 38 s&f of 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. 39 s&f in repair of 15mm bore dia bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. 40 s&f in repairs of 15mm bore dia stop valves, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. 41 s&f of water closet ( squatt pattern ) of vitreous china squatting pan of pattern orrisa pattern size 580 x 440 mm white with integral foot rests ( excluding flushing cistern and flush pipe ) including connection to trap and flushing pipe anti syphonic pipe etc complete including p or s trap set in and including necessary lean cement concrete, complete all as specified and directed. 42 s&f of vitreous china wash down water closet pan ( pedestal pattern ) , white ( excluding fixing bolts, flushing cistern and flush pipe ) and making good the floor, complete all as specified and directed. 43 s&f of 100mm bore of pipe ‘p’ or ‘s’ traps without vent horn, complete all as specified and directed. 44 s&f of pvclow level flushing cistern 10 litre capacity, valveless syphonic action type complete with inlet, ball valve, float valve, bends brackets, rawl plug, brass screws handle etc complete having bis description mark with is:2731 with and including suitable size of ms brackets, plug, screw all as required incl taking down existing high level / low level flushing cistern any type disconnecting pipes and jointing with new one etc, and making good the floors / walls as per existing floor finish / wall finish including 32 mm bore pvc flush pipe and jointing with water closet of any type, complete all as specified and directed. 45 s&f of pvc connections 15mm size with ptmt nuts of length 450mm, all as specified and directed. 46 s&f of towel rail 450mm long of ptmt fixed with and including chromium plated brass screws and wooden / plastic cleats ( minimum weight 170gms ) , complete all as specified and directed. 47 s&f of grating doom 100mm dia of ptmt ( minimum weight 25gms ) , complete all as specified and directed. 48 s&f of 1mm thick stainless steel sink with drainage board kitchen or laboratory type with waste pipe, plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm, complete all as specified and directed. 49 dismantling water tanks of capacity exc 500 and n exc 1000 litres and removing to store, complete all as specified and directed. 50 s&f of rotational moulded polyethylene water storage tanks of capacity 1000 litres ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part l and directed. 51 s&f in repairs of 20 mm bore dia ball valves high pressure of ptmt with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. ( minimum weight 15mm 142gms / 20 mm 210 gms. / 25mm 455gms / 40mm 690 gms ) , complete all as specified and directed. 52 supplied and fixed in repair of 15 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. 53 supplied and fixed in repair of 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. 54 dismantling of wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and directed. 55 s&f of anodised aluminium snap grid frame work of size of grid 605mm x 605mm for false ceiling, complete all as specified and directed. 56 m&l for 4mm thick non asbestos fibre cement building boards fixed or laid / inserted to timber / gi / aluminium framework with screws in ceiling flat or sloping, complete all as specified and directed. 57 demolition and breaking up drain pipes ( pvc ( swr ) , salt glazed ware, ac or reinforced concrete ) of 150mm bore including accessories set in cement mortar and removing rubbish from site, complete all as specified and directed. 58 demolition and breaking up drain pipes ( pvc ( swr ) , salt glazed ware, ac or reinforced concrete ) of100mm bore including accessories set in cement mortar and removing rubbish from site, complete all as specified and directed. 59 m&l for 150mm internal diameter salt glazed stoneware drain pipes laid in trenches and jointed all as specified and directed. 60 m&l for 100mm internal diameter salt glazed stoneware drain pipes laid in trenches and jointed all as specified and directed. 61 m&l for plain cement concrete ( 1:4:8 ) bed, type d 2, ( using 40mm graded stone aggregate ) to drain pipes 150mm bore including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed. 62 m&l for plain cement concrete ( 1:4:8 ) bed, type d 2, ( using 40mm graded stone aggregate ) to drain pipes 100mm bore including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed. 63 dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and directed. 64 m&l for 100mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, complete all as specified and directed. 65 m&l for 100mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed. 66 s&f of 100mm bore dia cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) fitted with oval access doors, complete all as specified and directed. 67 s&f of 100mm bore dia cast iron cowls, complete all as specified and directed. 68 demolition of cement concrete ( unreinforced ) in ground floor and pavings not exc 15 cm thickness ( below or above ground level ) , complete all as specified and directed. 69 m&l for 75 mm thick plain cement concrete ( 1:3:6 ) , type c 2 ( 40 mm graded stone aggregate ) as in plinth protection, hard standing, path etc including finish the surface even and smooth without using extra cement, complete all as specified and directed. 70 m&l for 40mm thick plain cement concrete ( 1:2:4 ) , type b 1, ( using 20mm graded stone aggregate ) as in sub base, sub floors, floors, pavings, roof treatment etc., complete all as specified and directed. 71 m&l for hardcore using broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed. 72 demolition of brickwork or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed. 73 m&l for brickwork with fly ash bricks ( old size bricks ) , straight or curved on plan exc 6m mean radius, built in cement mortar ( 1:6 ) , complete all as specified and directed. 74 m&l for plain cement concrete ( 1:3:6 ) , type c 2 ( 40 mm graded stone aggregate ) in surface channels and drains, complete all as specified and directed. 75 m&l for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds mitered / stopped ends etc all as specified and as directed. 76 taking down chowkhatsor frame not exc 1.50 sqm each with shutter ( without taking off shutters from the frame ) , complete all as specified and directed. 77 taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters ( without taking off shutters from the frame ) , complete all as specified and directed. 78 taking down shutters of any description n exc 1 sq. m each, complete all as specified and directed. 79 taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each, complete all as specified and directed. 80 dismantling timber scantlings 40 sqcm and over in section, in any position ( unframed work ) , all as specified and directed. 81 s&f of second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. 82 m&l for preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with one coat of creosote oil, complete all as specified and directed. 83 m&l for second class hard wood, 35mm thick plain, framed, panelled shutters ( any number of panels ) , with panels of timber flat on both sides ( feather edged ) , or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed. 84 s&f of 35 mm thick ( batten thickness ) second class hard wood, glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc , divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded with cut mitred beds for securing glass etc, supplied and fitted to chowkhats completeall as specified and directed. ( note : the dimension of the various components or parts of shutters shall be as specified in clause 8.24 ( a ) of mes ssr 2009 part i ) 85 m&l for second class hard wood, 30mm thick glazed and skeleton windows shutters, ventilators shutters etc. are provided with stiles and rails, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in ssr part i, section 8 clause 8.24 ( b ) ; supplied and fitted to chowkats, complete all as specified and directed. 86 s&f of solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. 87 s&f of factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing and as directed. 88 s&f of 100mm size butt hinges, medium weight, cold rolled mild steel, and fixed, all as specified and directed. 89 s&f of 75mm size butt hinges, medium weight, cold rolled mild steel, and fixed, all as specified and directed. 90 s&f of 125 mm size aluminium handles, cast type, anodised, all as specified and directed. 91 s&f of 100mm size aluminium handles, cast type, anodised, all as specified and directed. 92 s&f of 200mm long aluminium anodised, barrel tower bolts of extruded section and fixed, all as specified and directed. 93 s&f of 125mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, all as specified and directed. 94 s&f of 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, all as specified and directed. 95 hacking out old broken glass, exc 1.5 sqm ( any thickness, quality or description ) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. 96 s&f of 3.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed. 97 s&f of 3.0mm thick sheet glass ground or obscured or frosted, on one side, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed. 98 s&f in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed. 99 s&f of bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks ( stay ) , heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to fe 290 gde e 165, complete all as specified and directed. 100 m&l for plain cement concrete ( 1:3:6 ) , type c1 ( using 20mm graded crushed stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. 101 s&f in repair of small fittings such as brackets of any type latch and hinge block, shaped door window stops and the like in second class hard wood article not exc 200 cucm each, complete all as specified and directed. 102 taking down eaves gutters and rainwater pipes ( any size or pattern ) , including all fittings, heads, shoes, bends, swan necks, etc., including cleaning or refixing or removal to store ( measured overall as fixed along the centre line over fittings and accessories ) , complete all as specified and directed. 103 s&f of 110mm bore pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. 104 s&f of 110mm bore pvc ( swr ) bends any radius, complete all as specified and directed. 105 rough excavation not exceeding 1.5 m deep and getting out in soft / loose soil, all as specified and directed. 106 returning filling in soft / loose soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm, complete all as specified and directed. 107 removal of surplus excavated soils to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point, complete all as specified and directed. 108 m&l for plain cement concrete ( 1:2:4 ) , type b 0 ( using 12.5 mm graded stone aggregates ) in coping, bed plates, parepet, plinth course including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. 109 demolition ofreinforced cement concrete ( reinforcement cut as required to facilitate demolition ) of any description and in any position not specifically provided for, complete all as specified andas directed. 110 use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete on square rectangular on plain or polygonal, complete all as specified and directed. 111 m&l for providing precast cement concrete ( 1:2:4 ) , type b 1 ( using 20mm graded stone aggregate ) as in landings, cover slabs ( for man holes, drain etc. ) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces with plain fair faces, including chamfers, weatherings, throating etc. and set in cement mortar ( 1:4 ) , complete with joints to match the surface, complete all as specified and directed. 112 m&l for mild steel tmt bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookingends and binding with mild steelwire ( annealed ) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. 113 m&l for mild steel tmt bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips, all as specified and as directed. 114 m&l for reinforced cement concrete ( nominal mix ) ( 1:2:4 ) , type b1 ( using 20 mm graded stone aggregate ) as in columns, pillars, piers, posts and struts, complete all as specified and directed. 115 s&f in repair of curtain rails / harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc., complete all as specified and directed. 116 taking down copper / aluminium point wiring ( light, fan, socket or power ) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed. 117 taking down carefully sub main wiring of any size / core / type including conduit / cashing / batten of any type and making good disturbed surfaces to match with the existing surface roof / wall / floor, complete all as specified and directed. 118 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for light / fan / bell on independent board, point controlled by one switch including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 119 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for light / fan on independent board, point controlled by two way switchs including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) three run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 120 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one 3 pin socket outlet 5 amps on the same board with other switches including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 121 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one 3 pin socket outlet, 5 amps on independent board, point controlled by one switch including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 122 m&l for point wiring with 2.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 25mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one 3 / 5 pin socket outlet, 5 / 15 amps on independent board, point controlled by one switch including 2.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( i ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 2.5 sq.mm for phase and neutral and one run of 2.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed ) 123 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one bell / buzzer point controlled by one push button on the same board with other switches or independent including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 124 m&l for modular switch one way 6 amps, 1 module, 240 volts, all as specified and directed. 125 m&l for modular switch two way 6 amps, 1 module, 240 volts, all as specified and directed. 126 m&l for modular bell push 6 amps 1 module, 240 volts, all as specified and directed. 127 m&l for modular socket, 6 amps 2 / 3 pin combined 2 module, 240 volts, all as specified and directed. 128 m&l for modular socket, 6amps / 16amps 2 / 3 pin combined 2 module, 240 volts, all as specified and directed. 129 m&l for modular switch one way 16 amps, 1 module, 240 volts, all as specified and directed. 130 m&l for ceiling rose, 3 phase / pvc / polycarbonate, isolated body, three terminal, 240 volts, all as specified and directed. 131 m&l for modular blank plate, 1 module, 240 volts, all as specified and directed. 132 m&l for modular white cover plate with frame, 2 module, 240 volts, all as specified and directed. 133 m&l for modular white cover plate with frame, 3 module, 240 volts, all as specified and directed. 134 m&l for modular white cover plate with frame, 4 module, 240 volts, all as specified and directed. 135 m&l for modular white cover plate with frame, 6 module, 240 volts, all as specified and directed. 136 m&l for modular metal flush box, 1 / 2 module, 240 volts, all as specified and directed. 137 m&l for modular metal flush box, 3 module, 240 volts, all as specified and directed. 138 m&l for modular metal flush box, 4 module, 240 volts, all as specified and directed. 139 m&l for modular metal flush box, 6 module, 240 volts, all as specified and directed. 140 m&l for buzzer, ding dong ac. 230 volts, single pole, all as specified and directed. 141 supply and fixing in repair / replacement of led tube lights fitting 4feet, 1x 22w, 230v, decorative ultra slim extruded aluminium batten fixure with high lumen output, environmental friendly, all as specified and directed. 142 supply and fixing in repair / replacement of decorative box type fitting suitable for 4feet led tube light, 1x 22w, 230v, bipin holder, connector block, driver etc. with all accessories internally pre wired connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and pvc square blocks for fixing led fittings, all as specified and directed. 143 m&l in repair / replacement of lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. 144 supply and fixing in repair / replacement of building security light fittings new generation energy saving and enviornmental friendly long life versatile pressure die cast aluminium ip66 protection with acrylic cover of led 35 watts luminaire including gi bracket of suitable size with clamp, complete all as specified and directed. 145 s&f of sub main wiring with two single core 2.5 sqmm pvc ( frlsh ) copper conductor, insulated multistranded unsheathed cable medium grade including pvc conduit concealed of required size ( not less than 32mm ) conforming to is 2079 1973 with accessories for sub main connection including 2.5 sqmm pvc ( frlsh ) insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified and directed. ( note: three runs of 2.5 sqmm pvc frlsh copper conductor shall be measured as one unit length ) . 146 s&f of sub main wiring with two single core 4.0 sqmm pvc ( frlsh ) copper conductor, insulated multistrandedunsheathed cable medium grade including pvc conduit concealed of required size ( not less than 32mm ) with accessories for sub main connection including 4.0 sqmm frlshinsulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly, all as specified and directed. ( note : three runs of 4.0 sqmm pvc frlsh copper conductor shall be measured as one unit length ) . 147 s&f of sub main wiring with two single core 6.0 sqmm pvc ( frlsh ) copper conductor, insulated multistranded unsheathed cable medium grade including pvc conduit concealed of required size ( not less than 32mm ) with accessories for sub main connection including 6.0 sqmm pvc ( frlsh ) insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified and directed. ( note: three runs of 6.0 sqmm pvc frlsh copper conductor shall be measured as one unit length ) . 148 supply and fixing in repair / replacement of triple pole and neutral ( tpn ) db with sheet metal enclosure, 4 way, double door, 415 volt suitable for mounting incoming and outgoing mcbs, complete all as specified and directed. 149 supply and fixing in repair / replacement of sheet metal enclosure, double door for mcb dbs, 8 way single pole & neutral ( spn ) and current carrying capacity of 200 amps rated bus bar suitable for 240 volt, ac, 50hz, complete all all as specified and directed. 150 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of single pole ( sp ) and current carrying capacity of 5 to 32 amp duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, complete all all as specified and directed. 151 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of single pole & neutral ( spn ) and current carrying capacity of 32 amps duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, all as specified and directed. 152 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of single pole & neutral ( spn ) and current carrying capacity of 40 to 63 amp duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, all as specified and directed. 153 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of four pole ( fp ) and current carrying capacity of 63 amp duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, all as specified and directed. 154 material and labour for earthing complete with galvanised steel earth plate electrode 60cm × 60cm× 6mm thick, buried directly in ground ( earth pit not less than 2.25 metres deep below ground level ) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised iron or steel earth lead wire 4.0mm dia size by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no. 3 ofmesssrpart i, connected to earthing test point all as specified or indicated including testing on completion, includingnecessary excavation and earth work in any type of soil, gi pipe 20mm dia light grade for watering and gi 15mm dia light grade pipe for protection of earth wire etc. upto test point, pcc chamber with pcc cover in cement concrete ( 1:2:4 ) type b 1 ( using 20mm graded stone aggregate ) , funnel, wire mesh, charcoal dust, salt etc, connected to db as indicated, complete all as specified and as directed.notes: contractor should conduct necessary test such as earth continuity, earth resistance test in presence of engineer in charge. 155 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, laying of underground cables etc. or for shafts, wells, cesspits, manholes, pier holes, under groung cables etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil, complete all as specified and directed. 156 m&l for sand filling under floors or in foundations or for protection of cable etc. including watering and consolidation, complete all as specified and directed. 157 supply and laying of old size burnt clay fly ash building bricks designation 75 ( kg / cm2 ) laid flat equal to width of bricks, perpendicular to under ground ( ug ) cable over the dry sand cushioning, for cable protection, complete all as specified and directed. 158 dismantling / taking out old unserviceable service connection cables / under groung cables, of any grade / type of size as below from pole / wall / cable duct / under ground trench etc, all as specified and directed. 159 supply and laying in trenches, fixed to wall / pole xlpe insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, 4.0 core, cross sectional area 16 sq.mm, complete all as specified and directed. 160 supply and laying in trenches, fixed to wall / pole xlpe insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, 4.0 core, cross sectional area 25 sq.mm, complete all as specified and directed. 161 m&l for 40mm dia steel tubes ( light grade ) galvanised with all fittings, laid in trenches / wall / pole / road crossing for protection of underground cable / earth strip, all as specified and directed. 162 m&l for cutting existing road / hard standing not exc 20x30 cm in wide and depth getting out excavated material for laying cable / gi tube, returning filling and well ramming wateringfinish suraface 10 cm from top using pcc 1:3:6; including removal of surplase soil, all as specified and directed. 163 note 1: ( applicable for all parts / items ) : the bidders / contractors are advised to read tender document, all drawings & all / amendments and general condition of contracts before entry / quoting the rates.note 2: the contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount....

Eastern Coal Fields Ltd - West Bengal

39837586 lifting & lowering of pump, motor, bed plate of pump ( p1 ii, 8 stage, 500gpm along with motor and bedplate ) of 5 no. pit ( 30l / 2wd ) of chapuikhas colliery under satgram sripur area....

Coal India Limited - West Bengal

39357263 auction sale of scrap materials arising out of mscs non hazardous (mscs) 1 02049 mscs 2049 ms cs scraps arising out of old used and unserviceable scrap angle,channels,rejected coal tubs,rejected pumps,haulages etc., area lot no:ecl/kdp/agt/surveyoff/lot/2022/16 50000 kg satgram surface near workshop, kalidaspur project,satgram area 7204 18% 1% 2 02057 mscs 2057 ms/cs scrap arising out of chp structure and unserviceable ,scrap angle,channels,joist, plate,conveyor,structure etc. area lot no:ecl/sat/sp/agt/survey off/lot/2022/03 14830 kg satgram stagram project, satgram area 7204 18% 1% 3 02059 mscs 2059 ms/cs scrap arising out of old,used& unserviceable damaged head gear pulley,pinion,rejected gear,rejected switch body etc.,area lot no:sat/mc/mgr/scrap/lot/2022/02 30000 kg satgram near office, mithapur ® colliery, satgram area 7204 18% 1% 4 02062 mscs 2062 ms/cs scraps arising out of rejected pinion, rejected coal tub body, rejected coal tub wheel, bed plate, rejected & damaged girder, ms rail etc. 20000 kg satgram at surface pure searsole colliery,satgram area 7204 18% 1% 5 02051 mscs 2051 iron& steel materials of 1 no. chp at 5&6 pit of naba kajora 7150 kg kajora naba kajora, kajora area 7204 18% 1% 6 02052 mscs 2052 iron& steel materials of 1 no. chp at 2 pit of naba kajora 8530 kg kajora naba kajora, kajora area 7204 18% 1% 7 02053 mscs 2053 iron& steel materials of 1 no. chp of jambad ug 4300 kg kajora jambad ug,kajora area 7204 18% 1% 8 02055 mscs 2055 ms/cs scraps arising out of chp structure and unserviceable ,scrap angle, channels,joist,plate,conveyor structure etc. area lot no:ecl/sat/rbt/agt/surveyoff/lot/2022/728 333420 kg satgram ratibati colliery,satgram area 7204 18% 1% 9 02064 mscs 2064 ferrous material arising out of alu400, nta 855 engine,dc motors and generators,area lot no:e 20000 kg mugma regional workshop mugma regional workshop 7204 18% 1% 10 02065 mscs 2065 old used & unservicable ci/ms materials arising out of mixed scraps from scrap iron & steel cut pieces electrical switch pump body parts. ,area lot no:02 15000 kg kajora beside shed 4 area stores kajora area 7204 18% 1% 11 02066 mscs 2066 old used & unserviceble cs/ms shaft of different pumps. area lot no:03 2000 kg kajora inside shed 3 area stores kajora area 7204 18% 1% 12 02067 mscs 2067 old used & unservicable ci/ms materials of hemm spares. 75000 kg kajora infront of w/s and beside unit store jambad ocp,kajora area 7204 18% 1% ...

Bharat Coking Coal Limited - West Bengal

38980238 installation of pump and motor set with bed plate on the pontoon with fixing by bolting after line leveling and diversion of pipe line with making bends etc.with fixing by bolting at borira quarry for dewatering the coal face at docp....

Military Engineer Services - West Bengal

38895725 tender for provision of addl point wiring for md accommodation, provision of hard standing ( 30 sqm ) near bldg no p 16 , provision of 03xsentry post near mt park, gun par and office complex, provn of bathroom & toilet near bldg no t 88, t 12 & t 22 at raspunja mil station under ge ( central ) kolkata. 1 surface dressing not exc. 150mm deep and getting out in soft / loose soil, complete all as specified and as directed. 2 surface excavation not exc. 30 cm deep and ave. 15 cm deep and getting out in soft / loose soil, complete all as specified and as directed. 3 excavating in trenches, n exc 1.50 m wide and n exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft and loose soil complete all as specified and directed. 4 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft / loose soil complete all as specified and directed. 5 removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point as in soft / loose soil complete all as specified and directed. 6 m&lhardcore ( broken stone or boulders ) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 7 m&lsand filling under floors or in foundations including watering and consolidation complete all as specified and directed. 8 m&l treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface ( area of the sub structure in contact with backfill to be measured ) complete all as specified and directed. 9 m bed plate, hold fast etc, block benching, channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed. 14 m&l reinforced cement concrete ( design mix ) m 25 in roof beams, cantilevers, bres summers, lintels over 1.50 metre span, complete all as specified and as directed.note : formwork and reinforcement shall be measured and paid for separately under relevant items. 15 m&l reinforced cement concrete ( design mix ) m 25 as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.note : formwork and reinforcement shall be measured and paid for separately under relevant items. 16 m&l reinforced cement concrete ( design mix ) m 25 in chajja, etc., complete all as specified and as directed.note : formwork and reinforcement shall be measured and paid for separately under relevant items. 17 cutting chases, pinning in making good to facing where required and pointing in cm 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe / wiring etc. and making good cutting not exc 10cm girth complete all as specified and directed. 18 m&lpulverizes fly ashbricks using class a old size bricksstraigth or curved on plan exc 6m mean radius built in cm ( 1:6 ) cmplete all as specified and directed. 19 m&l brick work pulverizes fly ash bricks , half brick thick, old size, built in cement mortar 1:4, straight or curved on plan to any radius, complete all as specified and as directed. 20 m&l formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bres summers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed. 21 m&l formwork to chajjas and similar items including edges, flat, rough finished surfaces of concrete, complete all as specified and as directed. 22 m&l formwork tosoffits of suspended slab such as roof slab, floor slab, landings and similar works horizontal or sloping etc., not exceding 200mm thick , flat rough finished surfaces of concrete, complete all as specified and as directed. 23 s&f for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed. 24 s&fsolid pvc door frame of size 50mm x 47mm made out of 5mm wood grain printed pvc sheet reinforced with m.s. square tube, suppling & fixing in opening with and including 3 nos. stainless steel butt hinges 75mm long complete all as specified and directed. 25 s&ffactory made solid pvc moulded door shutter with wood free eps, 28 to 30mm thick ( stiles ) , with 2, 4, or 6 raised panel design with 2mm thick 3d wood grain moulded pvc sheet polyurethane painted on the front face & 2mm prelam pvc sheet on back face, supplying & fixing in frame at site complete all as specified and directed. 26 m&l tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clip complete all as specified and directed. 27 m&l tmt bars 8 mm dia , cut to length, bent to shape required including crank ing, bending and bindingwith and including mild steel wire ( annealed ) not less than 0.90 mm, complete all as specified and as directed. 28 m&l tmt bars 8 mm dia , cut to length, bent to shape required including crank ing, bending and bindingwith and including mild steel wire ( annealed ) not less than 0.90 mm, as in stirrups spacers and binders complete all as specified and as directed. 29 m&l steel work in tubular trusses / hollow section including special shaped washer etc. complete using erw or induction butt welded tubes conforming to is 4923 grade yst. 240 complete all as specified and as directed. 30 s&fplates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, without any attachmentconforming tofe 410 w ( gde e 250 quality b ) complete all as speci fied and as directed. 31 m&l mild steel screw bolts ( machine made ) 11mm to 15mm diameter of neck and length of bolt exc 22.5 cm and not exc. 30 cm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and as directed. 32 m&l pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.note : pressed steel frame should be filled with pcc 1:3:6 type c 0 ( using 12.50mm graded stone aggregate ) and cost of pcc shall be deemed included in quoted rate 33 m&l 1.50mm thick powder coated aluminium , three track sliding window with three nosshutters made ofaluminium section as per drawing no cwe / kol / td 33 of section no 1f 1f including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 nos , anodised aluminium snap beading screws etc.complete all as specified and as directed.note nos : ( i ) all window memberincluding fitting & fixture i.eframe, track, shutter frame, etc shall be deem toincluded quoted rate. only measure opening size of window. ( ii ) only glass for window & wire mesh shall be measure and paid separately under relevant items of boq . 34 s&f powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 600x450mm complete with following specification. ( a ) alu frames of size 45x45x1.2mm ( b ) rail & stile 45x45x1.2mm thick ( c ) 4.80mm thick frosted sheet glassnote : all ventilators / louvers memberincluding fitting & fixture shall be deem toincluded quoted rate. only measure opening size of ventilators / louvers 35 m&l framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work, conforming to fe 290, gde e 165, complete all as speci fied and as directed. 36 s&fbutt hinges extruded brass, bright polished size of hinges 100 mm ( medium weight ) and fixed with brass hinge pin complete all as specified and as directed. 37 s&f aluminium anodized, barrel tower bolt 200mm long, extruded section and fixed, complete all as specified and as directed. 38 s&f 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and as directed. 39 s&f aluminium alloy handle 150mm long, extruded section, fabricated type, anodized and fixed, complete all as specified and as directed. 40 s&f floor door stopper of aluminium body and tongue, anodised with hard drawn steel spring ( overall length of cover plate 150mm ) complete all as specified and as directed. 41 s&f pre painted galvalume aluminium zinc coating gi based corrugated / semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screw complete all as specified and directed. 42 s&f pre painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in ridge, fixed with self tapping screw complete all as specified and directed. 43 m&l false ceiling with e board classic , reinforced, designer series, board with hpsc of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards / files with aluminium anodised main t section 35mm x 23mm x 1.50mm cross tee 35mm x 23mm x 1.50mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges / sides duly suspended with 4mm dia gi hanger fixed with gi hooks 4mm dia and fastner as required at the site and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed. 44 s&f 40mm bore ms tubing medium grade and fixed at wall for ceiling complete all as specified and directed. 45 m&l for 150mm thick plain cement concrete type d 2 ( 1:4:8 ) ( using 40 mm graded crushed stone aggregate ) as in sub base complete all as specified and directed. 46 m&l for 75mm thick pcc ( 1:3:6 ) type c 2 ( using 40mm graded stone aggregate ) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directednote: construction joints will be provided at interval of 2.5m length and filled with bitumen 80 / 20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate 47 m&l cement concrete type d2 ( 1:4:8 ) using 40mm graded aggregate 75mm thick in sub bases, finishing concrete surfaces fair and even, complete all as specified and as directed. 48 m&l cement concrete type b0 ( 1:2:4 ) ( 12.5mm graded aggregate ) 25mm thick, in flooring, finishing concrete surfaces fair and even, complete all as specified and as directed. 49 m&l25mm thick rubber moulded prepolished coloured pcc chequered tiles of size 400 x 400 x 25mm set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 20mm thick screed bed in cm 1:6 complete all as specified and directed. 50 m&l joint free non skid ceramic coloured tiles 8 10mm thick ( square / rectangular ) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in cm 1:6 complete all as specified and directed. 51 m&l glazed ceramic coloured tile 450x350x7mm thick on vertical surfaces such as skirting, dados, risers to steps, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including 10mm thick backing layerin cement mortar ( 1:4 ) complete all as specified and as directed. 52 m&l rendering 15mm thick in cement mortar on fair faces of brick work or concrete surface of wallin cement morter ( 1:4 ) using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. . ( note: wpc shall be measured andpaid separately ) 53 m&l rendering 15mm thick in cm ( 1:6 ) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed 54 m&l rendering 5mm thick in cm ( 1:3 ) as in ceiling surfaces even & smooth without using extra cement complete all as specified and directed. 55 supply only liquid water proofing compound ( isi marked ) complete all as specified and directed. 56 s&f 4.80mm thick tinted sheet glass , pin head type and glazing in squaresexc 0.5 sq. m in each panecomplete all as specified and as directed. 57 m&l preparing new surfaces of walls and applying three coats of white wash, complete all as specified and as directed. 58 m&l preparing new surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed. 59 m&l preparing new surfaces of walls andapplying two coats of distemperoil emulsionover a coat of primer andapplied over 3mm thick birla / jk water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed. 60 m&l preparing newly plastered surfaces and finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) complete all as specified & directed. 61 m&l preparing new wood and wood based surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint ( first quality ) over a coat of pink primer, complete all as specified and as directed. 62 m&l preparing new steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint ( first quality ) over a coat of red oxide / zinc chrome primer, complete all as specified and as directed. 63 s&f20mm outer diameter cpvc pipes sdr 11 & plain cpvc sdr 11 fittings on walls / ceiling or laying in floors complete all as specified and directed. 64 s&f 25mm outer diameter cpvc pipes sdr 11 & plain cpvc sdr 11 fittings on walls / ceiling or laying in floors complete all as specified and directed. 65 s&f brass chromium plated two in one tap with wall flange screwed for 15 mm bore pipeas inrepair complete all as specified and directedmake : essco ( tqt 512an ) or equivalent make specified in the particular specification 66 s&fabs body chrome plated shower rose 125mm size including fixing to steel pipe or unioncomplete all as specified and directedmake : essco ( eos 542a ) or equivalent make specified in the particular specification 67 s&fshower arm 240mm long round shape with flange including fixing to steel pipe or union complete all as specified and directedmake : essco ( ale 536a ) or equivalent make specified in the particular specification 68 s&f 15mm bore brass chromium plated angular valve with wall flangecomplete all as specified and directed. make : essco ( tqt 526n ) or equivalent make specified in the particular specification 69 s&f 20 mm diachromuium plated tublar towel rail 600 mm longfixed to walls with chromium platedbrass screw including necessary fixing arrangement as in repair complete all as specified and directed.make : essco or equivalent make as specified in particular specification here in after. 70 s&f chromium plated health faucet with 8mm dia, 1.2 meter long flexible tube and wall hook with n.r.v ( back flow preventer ) complete all and specified and directedmake: essco ( cat no. ale ess 583 ) or equivalent make specified in the particular specification 71 s&f vitreous china white squatting pan ‘orissa’ pattern, size 580x440mm with ‘p’ or ‘s’trap, integral foot rest, providing joints between flush pipe and socket of wc pan including flushing cistern and flush pipe, fixing with and including provision of cement concrete beddingcomplete all as specified and as directed.make hindwire cat no 20143 or essco ( ecs wht 451 ) equvilant of approved make specified in particular specification. 72 s&f white pvc flushing cistern 10 litre capacity, low level valve less, syphonic action type with inlet, ball valve, float and handleincluding cutting and pinning in ends, making good disturbed surfaces in cement mortar 1:3 and fixedcomplete all as specified and as directed.make hindware cat no 510648 sw or essco ( ecs wht 201c ) equvilant of approved make specified in particular specification. 73 s&f pvc conncetions 15mm size with ptmt nuts of length 450mm complete all as specified and as directed. 74 s&f rotational moulded polyethylene ( hdpe ) water storage tank 1000litre capacity ( cylindrical vertical with closed top ) , black in colour, three layered construction, hoisted and fixed in position all specified in mes schedule part i including provision of 25mm x 100mm gi nippples with check nuts for inlet, outlet wash and overflow pipe including lowering of old / unserviceable water storage tank of any description, complete all as specified and as directed. 75 s&f vitreous china wash hand basin 550x400mm in size, white ( flat back or angle back type ) with 32mm dia brass chromium plated waste fitting, and 15mm dia pvc connector pipe, a pair of cast iron brackets duly painted stand including cutting and pinning in ends, making good disturbed surfaces in cement mortar 1:3complete all as specified and as directed. make hindware cat no 10100 sw or essco ( ecs wht 801 ) equvilant of approved make specified in particular specification. 76 s&f vitreous china white urinal, partion white of size 310x700mm complete all as specified and as directed. 77 s&f600mm x 450mm bevelled edge mirror of selected quality glass mounted on 6mm thick bwr plywood and fixed to wooden plug with chromium plated screw and cup washer complete all as specified and directed. 78 m&l 150mm dia reinforced concrete pipes, class np 3, laid and jointed with collars complete all as specified and directed. 79 m&l for concrete bed type c 2 ( 1:3:6 ) ( using 40mm graded crushed stone aggregate ) to 150mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. 80 s&f upvc ( swr ) soil, waste and ventilating pipe 75mm bore ( dia ) , type b single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and as directed. 81 s&f upvc ( swr ) soil, waste and ventilating pipe 110mm bore ( dia ) , type b single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and as directed. 82 s&fupvc ( swr ) 75mm bore branch pieces, double ( equal or unqual ) , ordinary or inverted ( spigot or socket type ) or with parallel branches or fitted with oval access doors and jointing with solvent cement complete all as specified and directed. 83 s&f upvc ( swr ) 110mm bore branch pieces, single ( equal or unqual ) , ordinary or inverted ( spigot or socket type ) or with parallel branches or fitted with oval access doors and jointing with solvent cementcomplete all as specified and directed. 84 s&fupvc ( swr ) 75mm bore cowls and jointing with solvent cement complete all as specified and directed. 85 s&f upvc ( swr ) bend 75mm bore ( dia ) , any type etc. and jointing with solvent cement, complete all as specified and as directed. 86 s&f upvc ( swr ) bend 110mm bore ( dia ) , any type, and jointing with solvent cement, complete all as specified and as directed. 87 s&f3 in 1 wall mixer for hot & cold water supply with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs & wall flanges screwed down for 15mm boreiron pipe incl necessary fittings & fixtures etc.as in repaircomplete all as specified and directed. make: marc ( mor 1141 ) , essco, cat mqt 517bkn ) or equivalent make as specified in the particular specfication. 88 s&f central hole for hot and cold water supply basin mixer, brass chromium plated screwed down for iron pipes, including necessary fittings etc as in repair , complete all as specified and as directed.make: marc ( mor 1100 ) , essco, cat tqt 516a ) or equivalent make as specified in the particular specfication. 89 s&fstack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof bore in pipe in 75mm to 150mm complete all as specified and directed. 90 m&l for point wiring with pvc insulated and unsheathed frlsh cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to is 694 1990 drawn through and including pvc concealed conduit 20mm dia medium dutywith all accessories including fabricated 1.6 mm thick ms terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm frlsh stranded pvc insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for one light or fanpoint controlled by one switch single pole one way for light / ceiling fan / exhaust fan / call bell point / switch socket outlet 5 amps complete all as specified and as directed.note: ( i ) red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. separate cable for earthing and neutral to be used for each individual circuit from the distribution board. ( ii ) cutting chases pinning shall be measured and paid separately under relevant item of sch a 91 all as per item no. here in before but one 3 pin 5 ampsswitch socket outlet on the independent board with other switch complete all as specified and directed by engineer in charge. 92 m&lpoint wiringwith 2.5 sqmm ( nominal area ) pvc insulated stranded single core unsheathed frlsh copper conductor cable 1100 volts grade drawn through with and including pvc concealed conduit 20mm dia medium duty with all fittings and accessories of casing caping ( like tee, bend etc ) complete fixed to walls / ceiling etc with and including 2.5 sqmm ( nominal area ) pvc insulated unsheathed, stranded, single core frlsh copper cable as earth continuity wire connecting to common earth point ( including supply & fixing of 1.6 mm thick pressed mild steelterminal boxes of suitable size with 3 mm thick pvc / plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 amp socket outlet on independent board complete all as specified and directed.note: ( i ) red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. separate cable for earthing and neutral to be used for each individual circuit from the distribution board. ( ii ) cutting chases pinning shall be measured and paid separately under relevant item of sch a 93 m&l point wiring with pvc insulated and unsheathed frlsh cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to is 694 1990 drawn through and including pvc casing caping of suitable size with all accessories including fabricated ms terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm frlsh stranded pvc insulated and unsheathed copper conductor earth continuity conductor to common earthand connecting to earth dolly for one light or fanpoint controlled by one switch single pole one way for light / ceiling fan / exhaust fan / call bell point / switch socket outlet 5 amps complete all as specified and as directed.note: red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. separate cable for earthing and neutral to be used for each individual circuit from the distribution board.. 94 all as per item no. 93.00here in before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by engineer in charge. 95 all as per item no. 93.00 here in before but one 3 pin 5 ampsswitch socket outlet on the independent board with other switch complete all as specified and directed by engineer in charge. 96 m&l fo point wiring surface type with 2.5 sqmm ( nominal area ) pvc insulated stranded single core unsheathed frlsh copper conductor cable 1100 volts grade drawn through with and including pvc casing caping with all fittings and accessories of casing caping ( like tee, bend etc ) complete fixed to walls / ceiling etc with and including 2.5 sqmm ( nominal area ) pvc insulated unsheathed, stranded, single core frlsh copper cable as earth continuity wire connecting to common earth point ( including supply & fixing of 1.6 mm thick pressed mild steelterminal boxes of suitable size with 3 mm thick pvc / plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 amp switch socket combination on independent board complete all as specified and directed. 97 s&f switch piano, flush type, sp, one way, 5 / 6 amps 230 / 240 volts, white / ivory finish complete all as specified and directed. 98 s&fswitch socket combination multipurpose 2 in 1, 3 pin 6 amps 230 / 240 volt flushtype complete all as specified and as directed. 99 s&fsocket outlet 3 / 5 pin, 6 amps, 240 volt flushtype complete all as specified and as directed. 100 s&f switch socket combination multipurpose 2 in 1, 3 pin15 amps 230 / 240 volt flushtype as in repair complete all as specified and as directed. 101 s&f ceiling rose surface bakelitethree terminals 240 volts complete all as specified and as directed. 102 s&f lamp holder suitable for batten fittings complete all as specified and directed by the engr in charge. 103 s&f surface and wall mounted led batten 4feets with 1x20w indoor decorative luminaries with and including electronic driver and 1x20w led lamp, pre wired including necessary electric connection copper flexible pvc cable of 0.5 sqmm 3 core not more than 1m in length from ceiling rose to light fittings including taking down unserviceable fittings complete all as specified and directed.make: magik cat no. bwpp020c or philips cat no. bn021cled22spsucwgr or equivalent in bajaj / havells 104 s&f exhaust fan ac single phase 240 v ofsize 300 mm sweep with louver, 50hz, rpm 1200 specially designed by toilet / bathroom in domesticventilationplastic body and blade, powder coated metalic finishes heavy duty motor, protective bird guard complete all as directed and specifed. 105 s&f electric water heater , storage type steel body with copper inner tank and heating element upto 2 kw capacity 25 litre, bee , 5 star rated complete with all accessories such as safety valve, thermostate , nrv and connecting pipe complete all as directed and specifed....

Northern Frontier Railway - West Bengal

37770499 auction sale of release u/s bg girder of span 2x12.2 (without bed plate) from br. no. 138 up at km 137 7 8 at btn stn boe sud, 2 nos. (in 4 i section), approx weight 15.838 mt....

Northern Frontier Railway - West Bengal

37770474 auction sale of 4x12.2m bg, deck plate, riveted girder ( in 16 i section ) without bed plate, x frame and lateral bracing angle realcased from br. no. 101 dn at km. 90 8 9 in btn. stn. flk guz.quantity 4 nos. ( in 16 i section ) approx weight 34.044 mt....

Eastern Coal Fields Ltd - West Bengal

37693032 administrative approval for miscellaneous fabrication jobs in dalurband colliery like fabrication of bed plate in domestic pump, welding job in weighbridge etc....

Eastern Coal Fields Ltd - West Bengal

37533391 administrative approval for miscellaneous fabrication and cutting jobs in dalurband colliery like fabrication of bed plate in domestic pump , welding job etc....

Bharat Coking Coal Limited - West Bengal

36488912 shifting of pump and motor set with repairing and modification of bed plate and re installation of pump and motor set with extension of pipe line at boriraquarry for dewatering the coal face at docp....

Eastern Coal Fields Ltd - West Bengal

36248844 shifting of cables, starters, switches, gate end box, endless haulage, bed plate, template, haulage rope, complete fitting of endless haulage & collection of materials etc. at 06no pit, manderboni colliery....

Eastern Coal Fields Ltd - West Bengal

36037527 supplying labour for fitting, fixing, setting and welding bed plate along with motors body at ghousick workshop pump house under kaliphari ? colliery....

Bharat Coking Coal Limited - West Bengal

35873032 repairing and modification of bed plate with installation of maxflow make 1200 gpm/ 220hp/150 mrs head pump and motor set at borira quarry for dewatering the coal face at docp....

Eastern Coal Fields Ltd - West Bengal

34963000 tender for work of job related with haulage drum and motor changing, bed plate repairing and transporting. new installation of endless haulage, lifting of gear box, electrical re organisation at 9 no pit of madhaipur colliery....

Northern Frontier Railway - West Bengal

34365756 auction sale of 3x12.2m, br, deck plate in six i pices, riveted girder without bed plates and bracings, released from br. no. 32 up, qty. 3 nos. approx weight 25.748 mt. in six pices....

Northern Frontier Railway - West Bengal

34365755 auction sale of 3x12.2m, bg, deck plate, riveted girder without bracing and bed plate, released from br. no. 34up, qty. 3 nos. in 18 pices, approx weight 25.748 mt....

Eastern Coal Fields Ltd - West Bengal

33927602 shifting of one ( 01 ) no of 150hp pump along with pump , motor , bed plate , pipe & starter , cable at khandra colliery under bankola area....

Eastern Coal Fields Ltd - West Bengal

33718882 dismantling , fitting & lowering of endless haulage, drum, motor, bed plate and 02 nos of pulley block from dhemomain incline to dhemomain pit colliery under sodepur area....

Directorate Of Industrial Training - West Bengal

33477008 supply, testing, installation & commissioning of different instruments, equipment & shop machineries of turner trade courses for various itis throughout the state of west bengal. , electrician trade : , 120. function generator technical specification: as per tender schedule e of nit , 123. discrete component trainer technical specification: as per tender schedule e of nit , 124. linear i.c. trainer technical specification: as per tender schedule e of nit , 125. digital i.c. trainer technical specification: as per tender schedule e of nit , 127. oil testing kit technical specification: as per tender schedule e of nit , 133. potential transformer technical specification: as per tender schedule e of nit , 137. d.c. shunt generator with control panel technical specification: as per tender schedule e of nit , 138. motor generator ( ac to dc ) technical specification: as per tender schedule e of nit , 139. d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker technical specification: as per tender schedule e of nit , 143. motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. technical specification: as per tender schedule e of nit , 144. ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. technical specification: as per tender schedule e of nit , 145. ac phase wound slip ring motor with starter switch technical specification: as per tender schedule e of nit , 147. synchronous motor with accessories like starter, excitation arrangements. technical specification: as per tender schedule e of nit , 148. thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement technical specification: as per tender schedule e of nit , 149. thyristor / igbt controlled a.c. motor drive with vvvf control 3 phase, 2 hp technical specification: as per tender schedule e of nit , 150. single phase transformer, core type, air cooled 1 kva, 240 / 415 v, 50 hz technical specification: as per tender schedule e of nit , 151. three phase transformer, shell type oil cooled with delta / star 3 kva , 415 / 240 v, 50 hz technical specification: as per tender schedule e of nit , 152. electrical machine trainer technical specification: as per tender schedule e of nit , 153. diesel generator set with changeover switch, over current breaker and water / air cooled with armature, star delta connections ac 3 phase technical specification: as per tender schedule e of nit , 157. a.c. series type motor 1 hp, 240 v, 50 hz technical specification: as per tender schedule e of nit , 159.manual motor coil winding machine technical specification: as per tender schedule e of nit , 160. ceiling fan coil winding machine 250v, 50 hz, 1 ?, with speed control technical specification: as per tender schedule e of nit , 161. primary current injection set 220v, 50 hz, 1 ?, output current 200 a ( min ) with timer technical specification: as per tender schedule e of nit , 162. stepper motor with digital controller technical specification: as per tender schedule e of nit , 163. shaded pole motor technical specification: as per tender schedule e of nit...

Eastern Coal Fields Ltd - West Bengal

33396546 shifting of cables, starters, switches, gate end box, endles haulage, bed plate, template, haulage rope, complete fitting of endless haulage & collection of materials etc. at 05no pit, mandarboni colliery....

Eastern Coal Fields Ltd - West Bengal

32942393 construction of foundation and installation of gearbox along with motor and bed plate for steel cord belt at main incline of shyamsudnarpur colliery under bankola area....

Eastern Coal Fields Ltd - West Bengal

32818308 construction of foundation and installation of gearbox along with motor and bed plate for steel cord belt at main incline of shyamsudnarpur colliery under bankola area...

Bharat Coking Coal Limited - West Bengal

32667794 dismantling and installation of two nos. pump motor set with repairing and modification of two nos. bed plate at borira quarry for dewatering the coal face at docp. ...

Eastern Coal Fields Ltd - West Bengal

32424366 making of bed plate, pump motor alignment, matching coupling, boring, key way making of coupling guard & fitting, painting of pump motor 02 set of gourangdi ( a ) colliery under salanpur area....

Eastern Coal Fields Ltd - West Bengal

32159294 shifting of 30 upper side p 1 pump, motor, bed plate with elec equipment complete set carrying and reinstallation and misc jobs at porascole east colliery....

Eastern Coal Fields Ltd - West Bengal

31285413 collection of one no. of centrifugal pump 60hp (db(100/400) alongwith bed plate from tilaboni colliery and place and fitting at water treatment plant of bankola area complex bankola area....