South Eastern Railways - West Bengal

40657517 supply of barrel bolt 76 mm etc.barrel bolt 76 mm etc.,barrel bolt 76 mm.drawing no.:irs drg. no. ca/ dw 2019, alt. nil.material and specification: aluminium alloy for parts a & d and is:2062/ 2011, amend. 1/ 2012, gr. e250a for parts b & c. [ warranty period: 30 months after the date of delivery ]...

Department of Defence Production - West Bengal

40419051 bids are invited for aluminium alloy tube to is 738 desgn 24345 w or 64430 wp condition id 108mm od 90mm length 480mm (q3) , al alloy tube to is 738: 1994 desgn 24345 w or 64430 wp condition, id= 108mm od= 90mm l= 260mm (q3) total quantity : 245...

Military Engineer Services - West Bengal

40337298 tender for provision of fasf at panagarh; 1 note ( applicable for all items / parts ) : the bidders / contractors are advised to refer notes on boq / scha before entry / quoting the rates.lumpsum price workedout by the tenderer for buildings works as listed in schedule ‘a’ part i. 2 lumpsum price workedout by the tenderer for earth work and excavationas listed in schedule ‘a’ part ii. 3 lumpsum price workedout by the tenderer for explosive limit boardsas listed in schedule ‘a’ part iii. 4 lumpsum price workedout by the tenderer for internal electrification as listed in schedule ‘a’ part iv. 5 lumpsum price workedout by the tenderer for external electric supply as listed in schedule ‘a’ part v. 6 lumpsum price workedout by the tenderer for external water supplyas listed in schedule ‘a’ part vi. 7 lumpsum price workedout by the tenderer for sewage disposal as listed in schedule ‘a’ part vii. 8 lumpsum price workedout by the tenderer for road / path / culvert / hard standingas listed in schedule ‘a’ part viii. 9 lumpsum price workedout by the tenderer forarea drainage as listed in schedule ‘a’ part ix. 10 lumpsum price workedout by the tenderer forlighting protection as listed in schedule ‘a’ part x. 11 lumpsum price workedout by the tenderer forrcc dunnage blocks as listed in schedule ‘a’ part xi. 12 lumpsum price workedout by the tenderer forfire point as listed in schedule ‘a’ part xii. 13 lumpsum price workedout by the tenderer forchain link fencing & gate as listed in schedule ‘a’ part xii. 14 lumpsum price workedout by the tenderer fordemolition & dismantling as listed in schedule ‘a’ part xiv. 15 sch a part xv ( misc b&r and e&m items ) note : this schedule is not pre priced by mes and the pre priced rate indicated as rs 0.00 under col. 5 siginifies this fact only.site clearence 16 material and labour for mixing of lime @ 2.5% by weight with earthin filling of traverse .note only lime and mixing with rotavator is to be paid under this item .laying , spreading and compaction etc is incl in forming embankment of earth. 17 internal electrification 18 supply & fixing led bulb 10 watt, b22 suitable for fitting in lamp holder batten type complete all as specified and as directed. 19 supply and fixingflame proof cum water proof led bulk head light fitting of 20 watt, certified by cmri, suitable for gas / vapor group of iia & iiib, zone 1 & 2 as per is 2148 ( 1981 ) and is 2206 part i having ip 66 degree of protection, cast aluminum alloy material and heat and impact resistance toughen a clear glass having anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connected up with three core flexible copper conductor cable with suitable size complete all as specified and as directed. . 20 supply and fixingflame proof led light fitting 40 watt, certified by cmri, suitable for gas / vapor group of iia & iiib, zone 1 & 2 as per is 2148 ( 1981 ) and is 2206 part i having ip 65 degree of protection as per is 2147 ( 1962 ) of die cast aluminum alloy lm 6 construction, light grade epoxy powder coating finish of shade number 631 as per is 5 having provisioning of one number internal earth and two numbers external screws of m4 / m5 size o ring endless neoprene rubber gasket, stainless steel hardware, two number 3 / 4 inch cable entry, cable glands, all internal electrical components pre wired, inside white and outside light gray, internal driver type epoxy powder coating, clear heat resistance well glass complete all as specified and as directed. . 21 supply and fixing flame proof distribution board, flame proof as certified by cmri, spn 8 way with din rail, suitable for isolators, mcbs and elcbs, suitable for group i, iib as per is 2148 ( 1981 ) , ip 65 as per is 2147 ( 1962 ) , cast aluminium alloy lm 6 conastruction, light gray epoxy shade no 632 of is 5 powder coating having having o ring neoprene rubber gasket, hardware in external steel construction complete all as specified and directed. ( note: isolators, mcbs and elcbs shall be measured and paid separately ) . 22 external electric supply 23 supply laying old size fly ash brunt building bricks, laid in trenchesover sand cushion laid with axis of bricks perpendicular to the axis of lt cable for cable protection, complete all as specified and as directed. 24 dismentling / taking down of cradles hexagonal / rectangular fabricated with galvanised steel wire any shape and size complete all as specified and as directed. 25 taking down old u / s danger notice plate any type and size complete all as specified and as directed. 26 taking up / out ht ug cables of any cross sectional area and connections and joints including pipes, bricks, etc of size 120 sqmm 3 core laying in trenches or fixing with walls / poles, segreating serviceable bricks / precast covers, pipes, cables etc, and keep in safe custody for reuse, complete all as specified and as directed. 27 relaying of ht ug cable ( serviceable cable obtained from item no. 24 here in before ) of size 120 sqmm 3 core complete all as specified and as directed. note : earthworks, sand cushioning, pre cast concrete cable cover, gi pipe, etc. will be measured and paid under appropriate items. 28 boring holes horizontally under road without damaging the surface of road ( minimum 1.0 metre below the road surface / footpath with the help of gi tubing not exc. 80mm bore ( dia ) for passing of ug cable, complete all as specified and as directed.note: gi pipe laid will be measured and paid separately under appropriate item. 29 m & l for cable route indicator of cast iron for lt / ht cable ( colour brown / blue respectively ) with 35x35x4mm ms angle iron post 1.00 mtr long embedded in pcc 1:3:6 type c1 foundation concrete 150mm x 150mm x 300mm deep complete all as specified and as directed. 30 supply , install, testing and commissioning of lt panel board outdoor type, cpri approved, platform mounted factory made of size 1.2 x 1.0 x 0.6m, totally enclosed dust and vermin proof openablefrom both front and rear side made out of 14 swg ( 3 mm ) thick crcams sheet and built upon suitable size angle ironframe work , having front and rear hinged doors, lifting lugs ( 2 nos ) , earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers.the cabinet and all members should be chemically treated with msr solution for anticorrosive treatment and apply spray paint with two coat of synethetic enamel paintover a coat of red oxide primer. the panel should be suitable for 415 volts , 50hz , 3 phase4 wire systemand internal connection should be provided with copper strips of suitable size, 04 nos copper bus bar 200 amps and necessary foundation workand comprisingfollowing: 31 ( a ) incoming mccb, 4 pole, 125 amps, 415 volt ac, 35 ka rupturing capacity 01 no. ( b ) ougoing mccb, 4 pole, 100 amps, 415 volt ac, 25 ka rupturing capacity 03 nos. ( c ) ougoing mcb tpn 10 amps, 10 ka, c series, 415 volts 02 nos. ( d ) changeover switch 125 amps 415 volts 01 no. ( e ) voltmeter & ammeter with selector switch. 32 supply , install, testing and commissioning of lt panel board outdoor type, cpri approved, platform mounted factory made of size 1.2 x 1.0 x 0.6m, totally enclosed dust and vermin proof openablefrom both front and rear side made out of 14 swg ( 3 mm ) thick crcams sheet and built upon suitable size angle ironframe work , having front and rear hinged doors, lifting lugs ( 2 nos ) , earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers.the cabinet and all members should be chemically treated with msr solution for anticorrosive treatment and apply spray paint with two coat of synethetic enamel paintover a coat of red oxide primer. the panel should be suitable for 415 volts , 50hz , 3 phase4 wire systemand internal connection should be provided with copper strips of suitable size, 04 nos copper bus bar 160 amps and necessary foundation workand comprisingfollowing: 33 ( a ) incoming mccb, 4 pole, 100 amps, 415 volt ac, 35 ka rupturing capacity 01 no. ( b ) ougoing mcb, 2 pole, 40 63 amps, 10 ka, c series, 230 volt ac 05 nos. ( c ) outgoing mcb tpn 10 amps, 10 ka, c series, 415 volts 03 nos. ( d ) time switches 415 v three phase of 20 amp rating with contactor 01 no. ( e ) voltmeter & ammeter with selector switch. 34 supply and fixing led street light fitting 45 watt 230 v ac, luminous efficacy 120 lumens / watt outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection including gi bracket of required shape & size as recommended by manufacturer, clamp of required length including nuts & bolts fixed on street poles complete. make: jaquar, model no:lsrt02s045xc or equivalent in havells / bajaj. ( note: 34 nos street light to be fitted on lt oh line pole ) 35 supply and fix junction box with terminals of size 155 x 210 x 92mm or nearest higher size made of polycarbonate body with ip 66 / 67 degree of protection, dust proof, water tight, shock proof, fire retardant, with internally embedded gasket fitted with heat treated bakelite terminals block and pvc glands for cable entry complete all as directed. make: hensel; cat no kf1616g. 36 supply, laying & testing pvc insulated, pvc sheathed electric control cables ( heavy duty ) with stranded copper conductor of size 1.5 sq mm, 3 core, 1100 volts grade to connect street light to junction box complete all as specified and as directed. 37 supply and fixing led search light with mororised system, led light should be 300watt, 230 v long range type with horizontal & vertical operational controls by remote control unit. 38 supply and fixing all in one outdoor solar led street light 30 watt with minimum 150 lumens, with in built scc, 100wp high efficiency mono crystalline solar pv module, minimum 12.8 v, 36 ah capacity lithium ferro phosphate battery, hdg tubular pole 7 mtr complete all as specified and as directed. make: havells / bajaj / jaquar. note: pcc foundation to erect the solar light pole shall be as per manufacturer recommendation and included in item rate. 39 external water supply 40 supply and laying of pipe ductile iron, socket & spigot type, class “k 9”, 200 mm nominal dia complete all as specified and as directed. 41 supply and laying of pipe ductile iron, socket & spigot type, class “k 9”, 150 mm nominal dia complete all as specified and as directed. 42 supply and laying of pipe ductile iron, socket & spigot type, class “k 9”, 100 mm nominal dia complete all as specified and as directed. 43 material & labour for di specials like bends ( any type, radius and angle ) tapers any type ( straight, bend, increasing, decreaing or double socket etc ) tee pieces single branch y junction, double branch, cross for di pipe upto 200 mm bore complete all as specified and as directed. 44 m & l construction of brick masonrychamber of 90 cm x 90 cmx 90 cm [ internal dimensions ] suitable for 150 mm / 200 mm bore sluice valve with pcc 1:4:8 type d2 using 40 mm graded stone aggregate for foundationbrick wall with sub class ‘b’ brick, oldsize built in cm1:6 pcc [ 1:2:4 ] type b1 [ using 20 mm graded stone aggregate for coping rendering in cm [ 1.4 ] 15 mmthick including provision of ms sheet cover 3 mm thick with two coats of synthetic enamel paint over a coat ofred oxideprimer to steel surfaces and locking arrangement including necessary excavation and earth work in any type of soil complete all as specified. 45 m & l construction of brick masonrychamber of 60 cm x 60 cmx 60 cm [ internal dimensions ] suitable for 50mm bore sluice valve with pcc 1:4:8 type d2 using 40 mm graded stone aggregate for foundationbrick wall with sub class ‘b’ brick, oldsize built in cm1:6 pcc [ 1:2:4 ] type b1 [ using 20 mm graded stone aggregate for coping rendering in cm [ 1.4 ] 15 mmthick including provision of ms sheet cover 3 mm thick with two coats of synthetic enamel paint over a coat ofred oxideprimer to steel surfaces and locking arrangement including necessary excavation and earth work in any type of soil complete all as specified. 46 road / path / culvert 47 material & labour for mixing of fly ash, clinker & stone dust in proportion of 1:3 :6 ( i.e 10% fly ash, 30% clinker and 60% stone dust materials ) laying thickness of 600mm ( compacted thickness ) in 3 layers , watering , ramming and compacting with vibratory roller to get min cbr value 8% and dry density 97 % placed at required camber and gradient completeas directed by engr in charge 48 material & labour for 225 mm th ( compacted th ) wet mix macadam ( wmm ) ( laid in three layer of 75mm each ) using 40mm graded aggregates , spread using mechanical paver as specifed, rolled with power roller exc 10 tonne not exc 12 tonne and consolidated as specifiedgradient and camber complete as specified and as directed. 49 material & labour for cleaning and preparing the road surface and marking good for road marking applying reflective thermoplastic white road marking paint ( hot application ) conforming to bis 3262 laid down through modern propelled road marking machine in a layer of crystalex and use of all ingredients such as binder, glass , beads, titanium dioxide , calcium carbonate , interfiller thermoplastic reqd for glass beads per sqm by incorporating the white glass beads for reflectivity in 100mm width complete all as specified and directed. 50 fire fighting system 51 supply and fixing portable fire extinguisher water co2 type, 9 ltr capacity confirming to is:940 / 6234suitable for fire fighting system. 52 supply and fixing portable fire extinguisher powder type suitable for fire type a b or c, of 10 kg capacity confirming to is: 13849 / 14609suitable for fire fighting system. 53 supply and fixing portable fire extinguisher co2 type, 5 kg capacity confirming to is:2878suitable for fire fighting system. 54 supply and fixing ceiling hook confirming to is:927suitable for fire fighting system 55 supply and fixing fire beater confirming to is:8096suitable for fire fighting system 56 supply and fixing fire bucket made out of ms irin, 9 ltr capacity confirming to is:2546suitable for fire fighting system. 57 supply and fixing shovelsuitable for fire fighting system 58 supply and fixing fire gong / hand siren confirming to is: 6026 suitable for fire fighting system 59 supply and fixing fire axe suitable for fire fighting system 60 digitel temp & humidity meter 61 supply, testing, commissioning and fixing of temperature & humidity data logger with the following specifications: ( a ) max / min : temperature reading over 0 to 100% rh :40 degree celsius to 70 degree celsius. ( b ) measurement ranges by pc with usb interface with data card and lcd monitor ( c ) memory for 32700 readings ( 16350 temperatures and 16350 humidity readings ) with long life battery pack with accessories including locking arrangement complete with fixing on wall. 62 electric siren 63 supply, install, test and commission electric motor siren for heavy duty application, ideal auidable range ( diametrical ) 8.0 kms, motor 5 hp ( 2880 rpm ) insulation class f / b, ip 44 , 415 volts, 3 phase, frequency 50 hz, aluminium casting bodied, horizontal impeller complete with all mounting and accessories including canopy made out of ms channel, cgi as required to protect from heavy rain fall complete all as specified and as directed. 64 supply and fix dol starter suitable for electric motor upto 5 hp, 415 volts, 3 phase complete all as specified and as directed. 65 dg set 66 supply, installation, testing and commissio ning silent diesel engine driven generating set 415 volts, 3 phase 4 wire, engine as per is:10001 / 10002 and alternator as per is: 13364 complete with relay panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per cpcb norms and foundation etc. of capacity 50 kva.technical specification : stroke 4, no. of cylinders 4, rpm 1500, cyl. configuration vertical lnline, dirction of rotation counter clockwise viewed from flywheel end, method of aspiration turbo charged after cooled, method of cooling coolant cooled, type of governor electronic, starting system 12v electric start, overload capacity 10% for 1hr. in every 12hrs. running, duty continuous, safety control low lube oil pressure, high coolant temp, applicable standards iso 3046, bs 5514, bore & stroke 97x128mm, displacement 3.84ltrs, compres sion ratio 17.5 :1, lube oil sump cap 9 ltrs, coolant capacity with engine jacket 15 ltrs. 67 alternator. rating: 50kvatype: brushless, excitation: self excited, self regulated ( avr ) , enclosure: spdp, enclosure protection: ip 23, rating: continuous, rated voltage: 415v, no of phases: 3ph, rated current: 50kva 208amps, frequency: 50hz, power factor: 0.8pf, class of insulation: h, voltage regulation: + 1%, overload capacity10% for 1hr for every 12hrs running, applicable standards: is 4722 / bs 5000.accessories. fuel tank suitable for 8hrs. capacity shall be supplied and to be mounted inside the canopy, exide make batteries 1 no.x12v, 90ah capacity, battery lead, anti vibration mounting pads ( fitted inside the canopy ) , residential silencer ( fitted on inside / top of canopy ) , first fill of lube oil & coolant. 68 amf control panel. the amf control panel shall be made of 16swg crca sheet, set / floor mounted, indoor type, dust and vermin proof and powder coated and suitable for 415v, 3phase, 50hz system. the panel will be incorporated inside the canopy and shall consist of the following features: microprocessor based amf controller having safety features with display of following engine & alternator parameters: engine display features low lube oil pressure, high water temperature, overspeed, low fuel level, rpm, no. of hours run, battery voltage. safeties llop, hwt, lfl, over speed & earth fault relay. alternator display features ampere, voltage, frequency, power factor, kw, kwh, kvar. safeties over current, over / under frequency, short circuit, current transformers of suitable ratio, 2 nos suitalby rated 4 pole power contactor for dg & mains, 1 no. suitably rated mccb with short circuit & overload protection as outgoing, indicating lamps for dg on / load on / mains on, mcb for control protection, battery charger with auto trickle & boost charging facility, toggle switch for control on / off. note: all engine & alternator parameters will be displayed through above controller only. 69 acoustic enclosure. acoustic enclosure should be fcri approved and made of specially procured 16swg crca sheet and structural sheet metal base frame and comply with cpcb / grihanorms with following features: the most compact, six sided, close, modular construction and detachable. meet cpcb / moef norms. sound level<75 dba at one meter distance under free field conditions as per norms. easy accessibility around the dg set, which ensures optimum serviceability. special powder coated enclosure, weather proof, corrosion resistant, environment friendly. specially designed lifting hooks. use of high quality hardware ensure longer life of enclosure. provision for emergency stop facility. fuel tank of 8hrs. running capacity is specially designed and mounted inside the enclosure as an integral part of acoustic enclosure. foundation / plinth / base : shall be provided as per manufacturers recommendations included in quoted rate of contractor.also necessary connection from main panel to dg panel with cables as per load to be included in quoted rate of contractor.note: rcc platform to mount dg set shall be as per manufacturer recommendation and included in item rate. 70 demolition & dismantling 71 taking down db / main switch of any size and making good disturbed surface of wall / floor complete all as specified....

Indian Army - West Bengal

40332515 tender for spare parts for geg tess veh; 1 steel 55c8 hex bar 6mm a / f tois:5517 78 part no 2 steel 25c8 r / bar dia 28mm tois:2004 1991 part no 3 steel 40cr4 r / bar dia 16mm tois:5517 93 part no 4 steel bar carbon h / r flat 40x4mm tois :2 part no 5 alluminium alloy plate 1715x1500x3mm part no 6 steel bar carbon h / r flat 30x12mm tois: part no 7 steel 40c8 wire 6mm tois: 1570 ( pt 2 / sec part no 8 steel 40cr4mo3 flat 65x40mm tois:5517 93 part no 9 steel bar round 42s dia 36mm tois: 226 7 part no 10 brazing flux silicofluse age silicon 650 part no 11 steel bar round dia 32mm bs:1501 pt.1 80 part no => limited...

District Magistrate - West Bengal

40266350 for procurement of furniture for the newly constructed new administrative building of district magistrate jhargram , reception table 1500 ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelvess , size:1981h x 916w x 486d1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with one drawer unit , size:1350 x 750 x 750 ( enzo table 4525 size shall be1350 width mmx 750 depth mmx 750 height mm .the table top shall be made of pre laminated particle board with 18 mm thick and 15 mm thick understructure covered with pvc lipping .there shall be locking provided for top drawers only , attractive black colour handles for all drawers plus only one colour is available beech.it shall have 1 drawer attachment and hdu attachment. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and must have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , sloted angel rack ( load bearing members of the system are made out of high strength hr steel having properties equivalent to grades specified by is 5986:2002 / is 2062:2006 the different types of material used for load bearing members such as uprights and beams are: steel type: fe 410 / equivalent ( or ) is:2062 e 250 / equivalent to is: 513d minimum yield strength: 255 mpa in addition to high strength, the raw material used for structural load bearing members possesses adequate ductility to ensure toughness. ) , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:1650x750x750 ( trident middle main deskwith eru ( rhs ) size shall be1650 width x 700 depth x 743 height ( main desk ) 1000 widthx 450depthx 743 height ( eru ) .top shall be of 18 mm thickness made of plt board with 2 mm edge banding. wenge and savannah maple plt board shall be used. the understructure shall be in pre laminated panels made with plt boards . 2 drawerand 3 drawer storage units with different combinations to support tops made with 18 mm plt boards of different colours.modesty and back panels made with 18 mm plt boards. the pedestals / storages shall be fitted with necessary locks. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene.4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , file storage ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , 3 seater visitor chair without arms ( 1 ) seat shell : the seat shell should bea welded assembly of seat, back and side frame. the seat and back should bemade of 0.12±0.013cm thk cr steel sheet with oblong perforations.they should bewelded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowder coated ( dft 40 60 microns ) . the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. seat size : 47.8 cm ( w ) x 44.6 cm ( d ) back size : 41.6 cm ( w ) x 23.0 cm ( h ) 2 ) understructure assembly: understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should bepowder coated ( dft 40 60 microns ) .the leg assembly should befitted with shoes and levellers in nylon. the leg structure should bedesigned with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould beof uneven flooring.connecting beam should befitted with snap locking end cap.lt also aids in side by side understructure alignment. 3 ) arm rest assembly: armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should bemade up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should bepowder coated ( dft 40 60 microns ) . armrest pad should beinjection molded in nylon and should befitted onto the armrest frame. 4 ) side table assembly: it should bea welded structure assembly made of 0.12±0.013cm thk cr steel sheet with oblong perforations which should bewelded to side strip of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowdercoated ( dft 40 60 microns ) and fitted to understructure assembly. side table size: 20.0 cm ( w ) x 37.2 cm ( d ) all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and must have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chairs ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal should be a.back size 47.5 cm. ( w ) x58.0 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. 3.armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. tubular frame: the powder coated ( dft 40 60 microns ) tubular frame should becantilever type & made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. m.s. er.w. tube. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , periodical display rack ( overall dimensions of all steel periodical displayrack shall be 900mm ( w ) x450mm ( d ) x1830mm ( h ) . rigid knockdown construction , panels shall be made from crca 0.6 mm thick and front frame shall be made from crca 0.8 mm thick . crca d grade as per is 513 . there shall be 5 level racks , display tray shall be suitable for fullscape size magazines, periodicals, aesthetically appealing metal tray at an angle for easy viewing . receding facility to access the storage behind . sliding on plastic rollers . behind storage shelving each of 5 level has a behind storage shelf . uniformly distributed load capacity per each shelf is 40 kg . leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , 3 seater visitor chair without arms ( 1 ) seat shell : the seat shell should bea welded assembly of seat, back and side frame. the seat and back should bemade of 0.12±0.013cm thk cr steel sheet with oblong perforations.they should bewelded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowder coated ( dft 40 60 microns ) . the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. seat size : 47.8 cm ( w ) x 44.6 cm ( d ) back size : 41.6 cm ( w ) x 23.0 cm ( h ) 2 ) understructure assembly: understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should bepowder coated ( dft 40 60 microns ) .the leg assembly should befitted with shoes and levellers in nylon. the leg structure should bedesigned with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould beof uneven flooring.connecting beam should befitted with snap locking end cap.lt also aids in side by side understructure alignment. 3 ) arm rest assembly: armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should bemade up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should bepowder coated ( dft 40 60 microns ) . armrest pad should beinjection molded in nylon and should befitted onto the armrest frame. 4 ) side table assembly: it should bea welded structure assembly made of 0.12±0.013cm thk cr steel sheet with oblong perforations which should bewelded to side strip of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowdercoated ( dft 40 60 microns ) and fitted to understructure assembly. side table size: 20.0 cm ( w ) x 37.2 cm ( d ) all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and must have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , sofa 3 str ( providing, supplying and placing of three seater sofa .overall size :width: 171cm depth : 86cm height : 77cmseating height : 39cmframe material : tropical solid wood , seat foam : polyurethane foam with recron layer. foam density : 18 kg / cubic cm. back foam : polyurethane foam with silicon fill at arms. foam density : 22 kg / cubic cm all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with one drawer unit , size:1500 x 750 x 750 ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chairs ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office storage ( glass door storwel shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the glass door storwel shall have a brass handle and a 2 way locking mechanism with shooting bolt .it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene.4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves, size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves, size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table & drawer, size: 2350x2350x750 ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chair plastic ( 1 ) seat / back: the seat and back should bemade up of injection moulded indoor grade polypropylene compound seat size : 52.5 cm. ( w ) x 53.2 cm. ( d ) back size : 51.6 cm. ( w ) x 40.5 cm. ( h ) 2 ) powder coated understructer:the powder coated ( dft 50±10 microns ) welded tubular frame should bemade from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm mserw tube. 3 ) shoe : the shoes should bemade of indoor grade polypropylene compound and snap fitted with tubular frame. 4 ) armrest : the armrest should bemade of indoor grade polypropylene compound and assembled over the tubular frame. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chair plastic ( 1 ) seat / back: the seat and back should bemade up of injection moulded indoor grade polypropylene compound seat size : 52.5 cm. ( w ) x 53.2 cm. ( d ) back size : 51.6 cm. ( w ) x 40.5 cm. ( h ) 2 ) powder coated understructer:the powder coated ( dft 50±10 microns ) welded tubular frame should bemade from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm mserw tube. 3 ) shoe : the shoes should bemade of indoor grade polypropylene compound and snap fitted with tubular frame. 4 ) armrest : the armrest should bemade of indoor grade polypropylene compound and assembled over the tubular frame. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:1650x750x750 ( trident middle main deskwith eru ( rhs ) size shall be1650 width x 700 depth x 743 height ( main desk ) 1000 widthx 450depthx 743 height ( eru ) .top shall be of 18 mm thickness made of plt board with 2 mm edge banding. wenge and savannah maple plt board shall be used. the understructure shall be in pre laminated panels made with plt boards . 2 drawerand 3 drawer storage units with different combinations to support tops made with 18 mm plt boards of different colours.modesty and back panels made with 18 mm plt boards. the pedestals / storages shall be fitted with necessary locks. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene.4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , file storage ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , desk size:3600 x 600 x 680 ( the worktop is made of 25mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. soft closing dual access flap provided for access to power supply and data cables. the understructure consists of mixture of 25mm and 18mm pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. anodised aluminium alloy 63400 wp profile is added at bottom edges for improving the aesthetics. the product has a knock down construction. a wire raiser made of 0.8mm crca ms is:513. it is epoxy polyester powder coated ( dft 40 60 microns ) for flow of wires and cables. a power box with 2 cutouts on either sides for standard 8 module anchor roma is provided. beside each cutout, an additional cutout with plate is provided for mounting audio visual cables ( eg. hdmi, vga a, etc ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( seat / back assembly: the seat should bemade up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded polyurethane foam. the back should bemade up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. the back ply and foam should bedesigned with contoured lumber support for comfortable seating posture. back size48cm. ( w ) x 76.0cm. ( h ) seat size51.0cm. ( w ) x 48.0cm. ( d ) 2. high resilience ( hr ) polyurethane foam: the hr polyurethane foam for seat and back should bemoulded with density = 45 + / 2 kg / m³ and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the armrest top should bemade of moulded polyurethane ( p.u ) and mounted on to a drop lift height adjustable type m.s. tubular armrest support chrome plated. the armrest height should beadjustable up to 6.5±0.5cm. in 5 steps & also has swivel adjustment of 22º±2° on both sides. 4.knee tilt synchro mechanism with seat depth adjustment mechanism: the mechanism should bedesigned with the following features: •360° revolving type. •single point control. •front pivot for tilt with feet resting on ground ensuring more comfort. •tilt tension adjustment. •4 position locking with anti shock feature. •seat back tilting ratio of 1:2 •seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positions 5.adjustable backrest: the backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 4 positions for correct position of lumber support. 6.pneumatic height adjustment: the pneumatic height adjustment has an adjustment of 9.0 ±0.3cm. 7.pedestal assembly:the pedestal should befabricated from 0.2 ± 0.02 cm thick hr sheet ( should be: dd 1079 / hrskin pass ) , chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twinwheel castors. the pedestal should be66.0±0.5cm. pitch center dia. ( 76.0±1.0 cm with castors ) . 8.twin wheel castors the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , visitor chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal should be a.back size 47.5 cm. ( w ) x58.0 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. 3.armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. tubular frame: the powder coated ( dft 40 60 microns ) tubular frame should becantilever type & made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. m.s. er.w. tube. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , projector trolley ( providing, supplying and placing of projector trolleyproduct size: vision projector trolley width: 545mm, depth: 838mm, height with castor: 1020mm. construction: rigid knock down construction. material: side panels, top / bottom panels, back panel, shelf panels, work surface panel, door andsupport frame panel are made from 18mm thick pre–laminated board of e1 p2 gradeand approved shade confirming to is 12823:1990 with 1.3mm pvc edge lipping.2 platforms are provided for projector and laptop usage. provision for the grommet is provided on the top panel, work surface panel andback panel for better wire management. lockable storage space with shelf is provided for storage of essential equipments. base plate assembly : dia 20mm ms rod bushes are fabricated by argo shield weldingon 8mm thk hr ( is 2062 ) plate and then powder coated. lockable castors are mounted onto the base plate assembly for ease of motion. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates:iaq gold ( by scs global ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:1650x750x750 ( trident middle main deskwith eru ( rhs ) size shall be1650 width x 700 depth x 743 height ( main desk ) 1000 widthx 450depthx 743 height ( eru ) .top shall be of 18 mm thickness made of plt board with 2 mm edge banding. wenge and savannah maple plt board shall be used. the understructure shall be in pre laminated panels made with plt boards . 2 drawerand 3 drawer storage units with different combinations to support tops made with 18 mm plt boards of different colours.modesty and back panels made with 18 mm plt boards. the pedestals / storages shall be fitted with necessary locks. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have in house test certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , file storage ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( providing, supplying and placing of mid back chair seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with changeable fabric upholstery covers and moulded polyurethane foam, together with moulded back spine cover. the back foam should bedesigned with contoured lumbar support for extra comfort. back size: 43.0cm. ( w ) x 46.0cm. ( h ) . seat size: 47.0cm. ( w ) x 50.0cm. ( d ) . high resilience ( hr ) polyurethane foam : the hr polyurethane foam should bemoulded with density = 45 + / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. armrests: the armrests should bemade of black integral skin polyurethane wtih 50 70 shore a hardness and reinforced with m.s. insert. the p.u. armrests should bethen fixed to black powder coated ( dft 40 60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. hr steel and fitted with claddings made of injection moulded polypropylene. permanent contact mechanism: the permanent contact mechanism should bedesigned with the following features: • 360° revolving type. • 14°±2° maximum back tilt only. • upright position locking. • tilt tension adjustment. spine cover: the, spine cover should beinjection moulded in black co polymer polypropylene. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0±0.3 cm. telescopic. bellow assembly: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly: the pedestal should befabricated from 0.2 ± 0.02 cm thick. hr sheet ( should be:dd 10791 hr ) , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0±1.0 cm with castors ) . twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii and have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves, size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table with drawer, size: 2350x2350x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , almirah ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , conference table u shaped 14 str ( the worktop is made of 25mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. soft closing dual access flap provided for access to power supply and data cables. the understructure consists of mixture of 25mm and 18mm pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. anodised aluminium alloy 63400 wp profile is added at bottom edges for improving the aesthetics. the product has a knock down construction. a wire raiser made of 0.8mm crca ms is:513. it is epoxy polyester powder coated ( dft 40 60 microns ) for flow of wires and cables. a power box with 2 cutouts on either sides for standard 8 module anchor roma is provided. beside each cutout, an additional cutout with plate is provided for mounting audio visual cables ( eg. hdmi, vga a, etc ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , officers chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal areaback size 47.5 cm. ( w ) x58.0 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , projector table ( providing, supplying and placing of projector trolleyproduct size: vision projector trolley width: 545mm, depth: 838mm, height with castor: 1020mm. construction: rigid knock down construction. material: side panels, top / bottom panels, back panel, shelf panels, work surface panel, door andsupport frame panel are made from 18mm thick pre–laminated board of e1 p2 gradeand approved shade confirming to is 12823:1990 with 1.3mm pvc edge lipping.2 platforms are provided for projector and laptop usage. provision for the grommet is provided on the top panel, work surface panel andback panel for better wire management. lockable storage space with shelf is provided for storage of essential equipments. base plate assembly : dia 20mm ms rod bushes are fabricated by argo shield weldingon 8mm thk hr ( is 2062 ) plate and then powder coated. lockable castors are mounted onto the base plate assembly for ease of motion. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates:iaq gold ( by scs global ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table ( providing, supplying and placing of main table . worktop made of 25mm thick pre laminated board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. access flap provided on work surface for wire management. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade confirming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. legs cube legs are fabricated from ms erw tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick ( as per is: 7138 ) . at the top surface of leg, support brackets of 3 mm thick hr ( as per is: 2062 ) are welded for fixing worktop. these are welded together by argo shield welding. this welded structure is coated with 50 micron epoxy polyester coating. at the base, a plastic cap with m8 molded insert is fixed, on to which a straight m8 leveler fitted which allows for adjustment of the height upto 50mm. cross members cross members in unitised t 2 desk series are made from 50mm x 25mm x 1.2mm thick erw tube ( as per is:7138 ) . these are coated with 50 micron epoxy polyester coating. cross members are assembled by friction fit pdc joinery and grub screws. there are always two cross members for one table. access flap soft closing access flap is used in unitized t 2 desk series. provision for standard size of 8 module electrical ( anchor roma ) is offered. access flap is made from aluminum extrusion, pdc parts made from aluminum alloy and plastic parts are made from nylon 6 and wire brush with nylon bristles. power box power box made with 0.8 mm thick crca ( is: 513 ) , with switch plate ( 8 module cutout provision for anchor roma ) . this is fixed with worktop along the depth at access flap position all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( the almirah shall have an overall size of916mm ( w ) x486mm ( d ) x1980mm ( h ) with welded construction. it should have the shelf thickness of 0.7 mm, back thickness of 0.8mm, door thickness of 0.8mm ( high yield strength ) and all other components shall have a thickness of 0.9mm. these components shall be made of crca ‘d’ grade high yield strength as per is:513. the storwel plain should have a mazak handle and three way locking mechanism with shooting bolts. it should have a height wise adjustable shelf mounting which shall have a uniformly distributed load capacity of max 40 kg. it should also have a m10 screw type leveller with hex plastic base. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . plenty of colour options and shelving options shall be available. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , conference table u shaped ( the worktop is made of 25mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. soft closing dual access flap provided for access to power supply and data cables. the understructure consists of mixture of 25mm and 18mm pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. anodised aluminium alloy 63400 wp profile is added at bottom edges for improving the aesthetics. the product has a knock down construction. a wire raiser made of 0.8mm crca ms is:513. it is epoxy polyester powder coated ( dft 40 60 microns ) for flow of wires and cables. a power box with 2 cutouts on either sides for standard 8 module anchor roma is provided. beside each cutout, an additional cutout with plate is provided for mounting audio visual cables ( eg. hdmi, vga a, etc ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , conference chair ( 1.seat assembly: the seat assembly should bemade up of 1.2 ±0.1cm. thick hot pressed plywood, upholstered with fabric upholstery covers and moulded polyurethane foam. seat size: 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.back assembly: the back asembly. should bemade of powder coated ( oft 40 60 microns ) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with contoured lumbar support for extra comfort. the back should beupholstered using double layer spacer mesh fabric with high tenacity yarn. back size : 46.5 cm ( w ) x 60.5 cm ( h ) 3.high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density =45+ / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 4.armrests: the one piece armrests should beinjection moulded from black co polymer polypropylene. 5.centre tilt mechanism: the mechashould be m should bedesigned with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • upright position locking. tilt tension adjustment.. 6.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. 7.telescopic bellow assy: the bellow should be3 piece telescopic type and injection moulded in black polypropylene. 8.pedestal assembly: the pedestal should beinjection moulded in black 33% glass filled nylon66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors. ) 9. twin wheel castors: the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back chair ( seat / back assembly: the seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per qa method described in ocp qlta pl14 18 ; upholstered with synthetic leather over moulded high resilience polyurethane foam. * high back size:51.8 cm. ( w ) x 75.2 cm. ( h ) * seat size:49.0 cm. ( w ) x 51.4 cm. ( d ) high resilience ( hr ) polyurethane foam: the hr polyurethane foam is moulded with density =55+ / 2 kg / m³ and hardness 16 ± 2 kgf as per is:7888 for 25% compression. armrests: the adjustable armrest is designed with the following features : • up down adjustment– 8 steps ( 8.0±0.5cm range ) • height adjustable armrest structure which is chrome plated & fitted with an armrest top. front pivot synchro mechanism: the adjustable tilting mechanism is designedwith the following features. • 360° revolving type. • single point control. • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 4 position locking with anti shock feature. • seat / back tilting ratio of 1:2. back height adjustability: back can be adjusted in 5 positions by manually. stroke of height adjustable spine is 7 cm. back height adjustability is applicable for for high back and mid back chair. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. pedestal assembly with castors:the pedestal is high pressure die cast polished aluminium and fitted with 5 nos. twin wheel castors. the pedestal is 65.0 ± 0.5cm. pitch center dia. ( 75.0 ± 1.0cm. with castors. ) twin wheel castor: the twin wheel castors are injection moulded in black pp. option of sliding seat mechanism : seat can be slide horizontaly as per user convenience. stroke of seat slide is 5 cm. this option is available for revolving pedstal type of chair. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , projector trolley ( providing, supplying and placing of projector trolleyproduct size: vision projector trolley width: 545mm, depth: 838mm, height with castor: 1020mm. construction: rigid knock down construction. material: side panels, top / bottom panels, back panel, shelf panels, work surface panel, door andsupport frame panel are made from 18mm thick pre–laminated board of e1 p2 gradeand approved shade confirming to is 12823:1990 with 1.3mm pvc edge lipping.2 platforms are provided for projector and laptop usage. provision for the grommet is provided on the top panel, work surface panel andback panel for better wire management. lockable storage space with shelf is provided for storage of essential equipments. base plate assembly : dia 20mm ms rod bushes are fabricated by argo shield weldingon 8mm thk hr ( is 2062 ) plate and then powder coated. lockable castors are mounted onto the base plate assembly for ease of motion. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates:iaq gold ( by scs global ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , medium back revolving chair ( 1 ) seat / back assembly: the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the stitched cover should bemade from spacer fabric and leatherette. cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) back size : 45 cm. ( w ) x 75.5 cm. ( d ) 2 ) armrests the armrest top should bemoulded from polyurethane ( pu ) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk ms e.r.w tube. the armrest height adjustable up to 6.5±0.5cm in 5 steps.the armrest structure should bepowder coated ( dft 40 60 micron ) . 3 ) active bio synchro mechanism ( fu3401 / 3402 ) : the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2 • the mechanism housing should bemade up of hpdc aluminium black powder coated. 4 ) seat depth adjustment seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. 5 ) adjustable back supportback frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6 ) pneumatic ht. adjustment the pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.9 ) twin wheel castor : 5 nos. twin wheel castors should beinjection moulded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: greenguard ( by ul ) , iaq gold ( by scs global ) , griha & svagriha, bifma level 2 ( should be visible in www.bifma.org ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , bookcase ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , office table with side table , size:2350x500x750 ( ascent desk with eru rhs size shall be 2100 width mm x 1600 depth mm x 765 height mm .the main top shall be of particle board ( melamine finish ) 1800 x 795 mm.the topshall be 25 mm thick plus 15 mm frame and 2 mm pvc lipping on top .also there shall be 0.35 mm pvc lipping on frame.the modesty panel shall be 1100 x 405 x 46 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the drawer front shall be of size 500 x 170 x 16 mm thick particle board ( melamine finish ) with 0.35 mm thick pvc lipping.the kbpt shall be 578 w x 284 d x 16 mm with 0.35 mm thick pvc lipping.the eru shall have all panels of 16 mm thick particle board ( melamine finish ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , high back revolving chair ( 1.seat / back assembly: the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.back size 47.5 cm. ( w ) x 69.5 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) 2.. high resilience ( hr ) polyurethane foam: the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. 3. armrests :the one piece armrests should beinjection moulded from black co polymer polypropylene. 4. center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. 5.pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6.telescopic bellow assemblythe bellow should be3 piece telescopic type and injection moulded in black polypropylene. 7.pedestal assembly:the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . 8.twin wheel castors:the twin wheel castors should beinjection moulded in black nylon. all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , griha & svagriha, green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) . , steel almirah with 4 shelves , size:1981h x 916w x 486d ( 4 door book case shall have the configuration of 914mm ( w ) x320mm ( d ) x1742mm ( h ) . the unique design provides the right rigidity to the top hinged doors , which shall facilitate easy use. the book case shall be made from prime quality crca steel with anti rusting treatment. it shall have a rigid knock down construction. the top pannel, back pannel and side pannel are made from 0.7mm high yield crca and other components from 0.8mm crca.each door shall have a 6 lever cam lock with common key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. scissor mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. each door should be provided with plastic side end caps as handle which is easy to grip. each compartment shall have a storage shelf with a udl capacity of max 80 kg. the 2 door book case shall have 18mm plb top straight edge with pvc lipping. the finishing shall include epoxy powder coated to the thickness of 50 microns ( + / 10 ) . all metal parts must be powder coated with epoxy polyester mixture ( >40 microns ) to prevent rust and stain. all ms components must be subject to 1000 hours salt spray test following the 7 tank galvanization and powder coating process. the product should be 90% mii, and should have the following certificates: iaq gold ( by scs global ) , greenguard ( by ul ) , green pro. product should have in house certificates. the oem should be part of the bifma compliance programme and should have 10 products or more registered as bifma compliant. ( also verifiable from www.bifma.org ) . manufacturer should have green guard ( by ul ) , green pro, griha, indoor advantage certification along with products certifications including aiota, indian design mark, bifma level 2 confoms to ansi / bifma e3 2014e furniture sustainability standard issued by bifma. other certificates iso 9001:2015. iso 14001:2015, iso 50001:2018, iso 45001:2018 ( tuv approved / obtained from nabcb central govt. accredited organization ) are mandatory. manufacturer should have bifma compliant certification for at least 10 of its products.supplier should have either oem or its dealer with 5 years setup of local service centre ( valid documentation must besubmitted bv the bidder ) ....

Forest Department - West Bengal

40259463 tender for supply of power chainsaw with 24 cutter bar and 2 stroke petrol engine in balurghat park of balurghat parks & gardens range under parks & gardens (north) division product dimensions 33 x 54 x 46 cm. single cylinder air cooled two stroke displacement: 62cc output power: 2.5kw petrol engine idle speed: 3,000 petrol engine speed: 12000 fuel tank volume: 550ml oil tank volume: 260ml guide plate length: 22 effective cutting width: 55cm chain model: 0.325 chain guide tooth thickness: 1.5mm material: aluminum alloy and plastic model: cs 62 saw blade size: 22, atleast 1 year warranty...

Military Engineer Services - West Bengal

40226364 tender for provision of rifle rack at armoury and construction of guard post with toilet at aai gate, ioc gate, south gate and wsa and construction of lady frisking cabin at afs bagdogra under ge ( af ) bagdogra.; 1 rifle rack at armourydemolition of ( un reinforced ) cement concrete in ground floors and pavings n.exc 15 cm thickness ( below or above ground level ) complete all as specified and directed. 2 taking down cement plaster on brick wall surfaces including reeking out jointshackingfor key scrubbing down with water etc. and removing the rubbish out of mod land complete all as specified and as directed. 3 taking down chowkhat or frame with shutter ( without taking off shutter from the frame ) area not exc 1.50 sqm each complete all as specified and as directed 4 taking down chowkhat or frame with shutter ( without taking off shutter from the frame ) area exc 1.5 sqm but not exc 4 sqm each complete all as specified and as directed 5 demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing in ceilingcomplete all as specified. 6 m&l for 100mm thickpcc ( 1:2:4 ) , type b2 ( using 40 mm graded stone aggregate ) finishing surfaces of concrete topping even and fair ( without using extra cement ) , complete all as specified and as directed. 7 m&l for 25mm thick cement concrete, 1:2:4, type b 1 ( using 20mm graded stone aggregate ) as insub base of floor complete all as specified and directed. 8 m&l for machine cut kota stone slab, 20 to 25mm thick as in flooring over and including screed bed 20mm thick in cm ( 1:6 ) laid & jointed with cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed. 9 m&l for machine cut kota stone slab 20 to 25mm thick over and including screed bed 15mm thickin cm ( 1:4 ) as in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed. 10 m&l for brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed. 11 m&l for 10mm thick rendering on brick work or concrete surfaces in cement mortar 1:6 finish even and smooth without using extra cement complete all as specified and as directed. 12 m&l for preparation of new plastered wall surfaces and applying two coats of oil bound distemper over 1.5mm thick birla / jk wall care putty over a coat of alkali resistant priming complete all as specified and directed. 13 m&l for complete removal of existing treatment of any description on old decorated wall surfaces and applying 1.5mm thick jk / birla wall care putty and two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed. 14 s&f 2nd class hard wood plain solid straight chowkhat or frame, wrought, framed, rebated on the solid, put together with glue and pinned at joint complete all as specified and as directed. 15 m&l for treating ends of posts back of chowkats etc. of area tarred exceeding 0.1 sqm but n.exc 0.5 sqm each with tar or coal tar black paint including sanding with clean sharp sand of newly tarred or painted surfaces complete all as specified and as directed. 16 s&f mild steelhold fast made of flat iron conforming to fe 290 gde e 165 of size 25 x 3 mm bent to shape required with splitting end and drilling holes for fixing nuts & bolts ( including nuts & bolts ) including treating the steel surfaces with tar or coal tar black paint and sanding neatly newly tarred surfaces with clean sharp sand all complete as specified and as directed. 17 m&l for pcc, 1:3:6, type c1 ( using 20mm graded stone aggregate ) for hold fast blocks complete all as specified and as directed. 18 s&f 40mm thick flush shutters, solid core construction with particle board core and ply wood face panels, commercial type on both sides and fitted to chowkats complete all as specified and as directed. 19 s&f for 100mm long stainless steel butt hinges, medium weight, cold rolled complete all as specified and directed. 20 s&f 150mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed. 21 s&f 300mm long aluminium alloy anodised sliding door bolt with hasp and staple ( bolt type ) and fixing with complete accessories all as specified and directed. 22 s&f aluminium anodised barrel tower bolt ofextruded section200mm long complete all as specified and directed. 23 m&l for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and as directed. 24 m&l for framed work as in doors or gates of angle or other section , including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to fe.290.gde e 165 complete all as specified and as directed. 25 s&f steel windows with side hung shutters with glazing bars, dovetailed or welded including projecting type hinges with steel handle, and steel peg stay complete all as specified and as directed. 26 s&f steel windows with side hung shutters without glazing bars, dovetailed or welded including projecting type hinges with steel handle, and steel peg stay complete all as specified and as directed. 27 m&l for framed work such as grills, gratings, etc., with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to fe.290, gde e 165 complete all as specified. 28 s&f 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. 29 s&f galvanised steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. 30 m&l for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. 31 s&f welded steel wire fabric supplied and fixed complete to wood or steel members complete all as specified and directed. 32 s&f powder coated galvanised iron snap grid frame work of size 600 x 600 mm for false ceiling comprising of main runner t section of size 38mm x 24mm x 0.40mm thickness, cross t of size 29mm x 24mm x 0.3mm thickness and wall angle of size 24mm x 24mm x 0.43mm thick suspended with 4mm dia gi wire from purlin @ 1.20m c / c and fixed with 4mm thick designer ceiling boards complete all as specified and directed. 33 dismantling plain or corrugated steel sheeting sheet any gauge thickness incl nainital or similar pattern roof coverings complete all as specified and as directed. 34 s&f 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with l or j hook and washers, in roofs, walls etc. with grade of zinc coating 275 etc. complete all as specified and directed 35 s&f 0.63 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings ( length and girth as fixed ) with grade of zinc coating 275 etc. complete all as specified and directed. 36 rifle rack at armoury ( internal electrification ) m&l for flameproof point wiring concealed type with 1.5 sqmm ( 22 / 0.30mm ) pvc insulated unsheathed single core stranded copper conductor flame retardant low smoke ( frls ) cable of working voltage 1100 volts grade conforming to is 694 drawn in and including steel surface conduit with all fittings and accessories such as flp flexible conduit, flp junction box bends etc. with 1.60 mm thick pressed steel or mild steel sheet sunk box, including 1.5 sqmm ( nominal cross sectional area ) pvc insulated unsheathed single core stranded copper conductor flame retardant low smoke ( frls ) cable as earth continuity amps single pole flp switch / dbs or common earth dolly for one fan / light point controlled by one 16 amps switch pole flp switch complete as per site requirement and all as specified & directed by engr in charge for one light point or one fan point controlled by one switch with cables 1.5 sq. mm size.note: unit rate include for cutting chases for conduits and sinking for boxes andmaking good to wall, floors etc. 37 switch flame proof rotary type with termination box in lm6, 16a, single pole 250v all as specified and directed by engineer in charge. 38 s&f led light fitting 2 x 16 / 20 watt flame proof, cimfr certified recommended for gas / vapour group of iia & iiib, zone 1 & 2 and ip 65 protection with die cast aluminum housing with heat resistant toughened glass, with led tube light fixtures driver, holders, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size all as specified and directed by engineer in charge. 39 s&f distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & mcbs 240volts, 200 amp rated bus bar with front openable cover suitable for sp & n 4 ways all as specified & directed. 40 s&f mcb sp 6 32 amps / 40 amps, 230 volts, 50 hz with 10 ka, c series all as specified & directed by engineer in charge. 41 s&f mcb spn / dp upto 32 amps, 230 volts, 50 hz with 10 ka, c series all as specified & directed by engineer in charge. 42 s&f of submain wiring with two single core pvc insulated unsheathed, multistranded flexible copper conductor 1100volts grade, frls type, cables 4 sqmm drawn through in and including rigid pvc heavy duty concealed conduits including 4 sqmm 1100volts grade, frls type, pvc insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. note: ( i ) two runs of cables and one run of continuous earthing cable drawn in conduit will be measured as one length of sub main. ( ii ) pvc conduit and its accessories is deem to be included in this item rates. ( iii ) unit rate include for cutting chases for conduits and sinking for boxes andmaking good to wall, floors etc. 43 m&l earthing complete withgalvanised steel earth plate electrode 60cmx60cmx6 mm thickness burried directly in ground ( earth pit not less than 2.25mtr deep below normal ground level ) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00 mm dia by means of nuts & bolts, check nuts and washers of galvanised incl pcc pit of 1:2:4 type b 1, cover reinforced with xpmweightnot less than 4 kg / sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in anytype of soil, charcoal dust, salt, light grade gi watering pipe 20mm dia with funnel and wire mesh and medium grade gi protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete allto as shown in electrical plate no 3 of mes sch 2009 ( part i ) connected main switch board all as specified and testing on completion. 44 rifle rack at armoury ( fire alarm system ) s&f indoor addressable detector complying with and type certified to en 54 addressable type multisensor detector with heat and smoke combination photoelectric / optical with base with self built intelligence all as specified and as directed. 45 s&f electronically addressable intelligent resettable type manual call point with mounting base complying with en 54 standard and lpcb approved with the specifications as appended below: ( a ) power 24v, =1.8ma ( alarm current ) ( b ) class a ( c ) initiating mode pressing the action plate manually resuming mode manually resumed by a special key, ( d ) ingress protection ip 43 & material abs. 46 supply rtu logic upgradation and development for central monitoring through wireless communication at master control station which includes the development of logic for false alarm which comes from addressable fire alarm control panel all as specified and as directed. 47 installation, testing and commissioning of addressable intelligent microprocessor based interactive and addressable fire detection system all as specified and as directed. 48 supply only two wire plug in detector base all as specified and as directed. 49 s&f two core copper conductor of size 1.5 sqmm frls flexible shielded cable complete all as specified and directed. 50 construction of guard postexcavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation .etc. in soft / loose soil complete all as specified and as directed. 51 m&l for cement concrete, ( 1:4:8 ) , type d2 ( using 40mm graded stone aggregate ) as in foundations complete all as specified and as directed. 52 returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm with excavated soil complete all as specified and as directed. 53 removing excavation material / soil n.exc. 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. 54 m&l for brick work with sub class `b bricks, straight or curved on plan exc 6m mean radiusbuilt in cement mortar 1:6 complete all as specified and directed. 55 m&l for 10 mm thick rendering in cm ( 1:6 ) onfair faces of brick work or concrete surfaces finished even and smooth without using extra cement on wall complete all as specified and directed. 56 m&l for 15 mm thick rendering in cm ( 1:4 ) on other than fair faces of brick work or concrete surfaces finished even and fair without using extra cement with using wpc 3% by weight of cement on wall complete all as specified. ( wpc shall be measured separately ) 57 m&l for 10mm thick rendering in cement mortar 1:4 on fair faces of concrete surfaces without using extra cement on ceiling complete all as specified 58 supply only water proofing compound complete all as specified and as directed. 59 m&l forpreparation of new plasteredsurfaces of wall andapplying two coats of oil bound distemper over a coat of alkali resistant priming paint complete all as specified and directed. 60 m&l forpreparation of new plasteredsurfaces and applying three coats of whitewash on ceiling complete all as specified and directed. 61 m&l for preparation of new plastered surfaces of wall and and applying two coats of exterior weather coats over a coat of weather coat exterior primer for camouflage design incl necessary scaffolding complete all as specified and directed. 62 m&l for rcc, 1:2:4, type b 0 ( nominal mix ) ( using 12.5 mm graded stone aggregate ) as in foundation, footing, foundation beam, plinth beam, base for columns, etc. complete all as specifiedand as directed. ( note: reinforcement shall bemeasured and paid separately. 63 m&l forrcc, 1:2:4, type b 0 ( nominal mix ) ( using 12.5 mm graded stone aggregate ) as in columns, etc. complete all as specifiedand as directed. ( note:reinforcement shall bemeasured and paid separately. 64 m&l forrcc, 1:2:4, type b 0 ( nominal mix ) ( using 12.5 mm graded stone aggregate ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specifiedand as directed. ( note: reinforcement shall bemeasured and paid separately. 65 s&f tmt bar mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookingends and binding with and including mild steel wire ( annealed ) not lessthan 0.9mm dia or securing with clips complete all as specified anddirected. 66 all as per item no. 65 above, but 5mm dia and over upto 10mm dia in stirrups, spacers and binders complete all as specified anddirected. 67 m&l for form work to sides of concrete foundation, footings, bases of columns, sides and soffit of foundation and plinth beam and similar works etc. for rough finished surfaces of concrete complete all as specified anddirected. 68 m&l for form work to sides of pillars, posts, columns etc. for fair finished surfaces of concrete complete all as specified anddirected. 69 m&l for formwork to soffits of suspended slabs such as roof slabs, floor slabs, shelves landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) for fair finished surfaces of concrete complete all as specified anddirected. 70 m&l for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs, sides of rcc / pcc bands in walls, horizontal or sloping and similar works exc 10 cm but not exc. 20 cm wide for rough finished surfaces of concrete complete all as specified and directed. 71 s&f 1000 litres capacity rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i complete all as specified and directed. 72 s&f ball valve 20mm high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed. 73 s&f 20mm bore gate valves with iron wheels head screwed both ends for iron pipe and fixed complete all as specified and directed. 74 m&l for cutting chasing pinning in making good to facing where required for concealed water tubing etc. n. exc 10 cm girth in brick wall complete all as specified and directed. 75 s&f 15mm bore ofmedium grade galvanised steel water tubing, with all fittings and fixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. 76 s&f 20mm bore ofmedium grade galvanised steel water tubing, with all fittings and fixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. 77 m&l for 15 mm thick plaster in cm ( 1:4 ) mixed with water proofing compound on roof slabs finished even and smooth without using extra cement after cleaning of roof surfaces with wire brushes complete all as specified and directed by engr in charge. notes : wpc shall be measured and paid separately. 78 m&l for water proofing treatment to roof slabs by applying one coat of bituminous / polymerized primer confirming to is 3384 @0.30 litre / sqm, by lying actetic polypropylene ( app ) modified membrane pre fabricated, reinforced with non woven polyester, of 3.0 kg / sqm ( minimum ) 3mm thick with minimum 75 mm side overlaps and minimum 100mm and applying one coat of bituminous aluminium paint over app membrane complete all as specified and directed. 79 m&l for applying evenly a tack coat of industrial bitumen 85 / 25 @ 1.2 kg / sqm including cleaning surface complete all as specified and directed. 80 m&l for roof trusses ( framed / un framed ) for purlin, rafter, crane gantries, door frame, rails and fastening and heavy bracket etc. ( beam, tee, angle iron or flat sections ) including distance pieces, cleats etc. complete all as specified and directed confirming to fe 290 ( gde e 165 ) . 81 m&l for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. 82 s&f pre painted galvalume aluminium zinc coating gi based corrugated or semi corrugated steel sheet 0.50 mm thick ( bmt ) of any colour having tensile strengthof 550 mps as in roof covering / cladding to wall fixed with self tapping screws all as specified and directed by engr in charge. 83 s&f powder coated galvanised iron snap grid frame work of size 600 x 600 mm for false ceiling comprising of main runner t section of size 38mm x 24mm x 0.40mm thickness, cross t of size 29mm x 24mm x 0.3mm thickness and wall angle of size 24mm x 24mm x 0.43mm thick suspended with 4mm dia gi wire from purlin @ 1.20m c / c and fixed with 4mm thick designer ceiling boards complete all as specified and directed. 84 s&f 110mm bore pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. 85 s&f pvc ( swr ) vent cowl 110mm bore complete all as specified and directed. 86 s&f 110 mm bore pvc ( swr ) bends any radius complete all as specified and directed. 87 s&f pvc ( swr ) floor trap plain with gratinghaving dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type b 1, ( 1:2:4 ) complete all as specified & as directed. 88 m&l for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 89 m&l for 75mm thick pcc, ( 1:4:8 ) , type d2 ( using 40mm graded stone aggregate ) as in floors complete all as specified and directed. 90 m&l for 25 mm thick cement concrete, type b 0, 1:2:4 ( using 12.5 mm graded stone aggregate ) as in sub floors etc. incl finishing the surface even & rough to receive screeding complete all as specified and as directed. 91 m&l for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 92 m&l for non skid coloured ceramic floor tiles of size of tile exc. 0.11 but n.exc.0.18 sqm each 7 mm thick as in floor laid over and including 15mm thick screed bed in cm 1:6, set, jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 93 m&l for 75mm thick pcc, ( 1:3:6 ) , type c 2 ( using 40mm graded stone aggregate ) as in plinth protection, laid in panels, finished the top surfaces even and fair without using extra cement complete all as specified. 94 m&l for colour glazed ceramic wall tiles of size 450x350x7mm thick on vertical surfaces laid over and including for rendering 10mm thick in cm ( 1:4 ) on vertical surface of wall, cement screed bet set and jointed in neat cement slurry and pointedin white or coloured cement to match complete all as specified and directed. 95 s&f cast iron body door closer hydraulically regulated, designation no. 3 universal type suitable for door shutters upto 851 to 1000mm in width and of weight 35 kg complete all as specified and directed. 96 s&f pvc connection 15mm dia and 450 mm long with 2 nos ptmt nuts with washerscomplete all as specified and directed. 97 s&f pvc white low level flushing cistern 10 ltr capacity with all fittings syphonic actiontype with inlet ball valve and float, handle with & including bracket andpvc flush pipe 32 mm bore complete all as specified and directed. 98 s&f white vitreous china wash down water closet pan ( pedestal ) pattern and trap ( excluding ) fixing bolts, flushing cistern and flush pipe ) including connection to drain ( or outgoing pipe ) and to flushing pipe, antisyphonage pipe, etc.complete all as specified and directed. 99 s&f plastic water closet sheet covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device complete all as specified and directed. 100 s&f vitreous china wash hand basin ( flat back ) of size 550x400mm including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia pvc waste pipe with connector, including cutting for and pinning in ends of brackets complete all as specified and directed. 101 s&f vitreous china squatting pan “orissa” pattern size 580mm x 440mm, white with p or s trap front or back inlet with integral foot rest ( excl flushing cistern & flush pipe ) &including connection to trap & to flushing pipe anti syphonage pipe etc. complete including making good to floor complete all as specified & as directed. 102 s&f vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white ( minimum ) , with grating and union for discharge pipe ( excluding flushing cistern, flush pipe and waste pipe ) , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed. 103 s&f cp soap dish fixed to wall with screw complete all as specified and directed. 104 s&f 15 mm bore chromium plated fancy type long boby bib taps with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. 105 s&f 15 mm bore chromium plated fancy type angle valve with elegant knob screwed down high pressure, with crutch or butter fly handle screwed for iron pipe or for unionscomplete all as specified and directed. 106 s&f powder coated aluminium ( minimum thickness of powder coating 50 micron ) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 107 s&f powder coated aluminium ( minimum thickness of powder coating 50 micron ) door shutters, aluminium section weighing not less than 0.55kg / m including necessary joining cleats, glazing clips, rubber neoprene packing, powder coated aluminium fittings such as handles 02 nos, 100mm long hinges 03 nos, sliding bolt 01 nos, tower bolt 02 nos in each door, powder coated aluminium snap beading and rubber gasket, screws etc. complete all as specified and directed. note:glass shall be measured separately. 108 s&f powder coated anodised aluminium window and ventilator shutters side hung type without sash bar, aluminium sections weighing 0.55 kg / m including necessary joining, cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as hinges type b 21 100 mm long ( 2 nos ) suitable handle 1 no complete all as specified and directed. 109 m&l for 5 mm thick sheet glass ordinary quality and glazingeach pane fixed with neopunerubber gasket in aluminium frame work complete all as specified and directed. 110 s&f solid pvcdoor frame of size 50mm x 47mm made out of 5mm wood grain printed pvc sheet reinforced with m.s. tube, supplying & fixing in opening as per specification & drawings complete all as specified. 111 s&f factory made pvc shutter panel pvc door shutter 30mm thick ( style ) consisting of frame made out of ms tubes for top and bottom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheetfor top rail, lock railand bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour pvc sheet to be fitted in ms frame welded / sealed to the stiles and rails with suitable pvc sheet beading and joined together with solvent cement , supplying and fixing in the frame at site as per specification & drawing as specified. 112 s&f 100 mm butt hinges, medium weightcold rolled, mild steel and fixed complete all as specified and as directed. 113 s&f 125mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. 114 s&f 150mm long aluminium anodised tower bolts of extruded section and fixed, complete all as specified and directed. 115 s&f cp toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated brass screws complete all as specified and directed. 116 s&f 20 mm dia aluminium anodised tubular towel rail, d type, 60 cm long between flanges fixed with brass screws complete all as specified and directed. 117 s&f health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete complete all as specified and directed. 118 s&f 15 mm bore chromium plated fancy type pillar tap for whbs with capstan heads, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed completeall as specified and directed. 119 s&f 600 mm x 450 mmsize bevelled edge mirror of selected quality glass, 5.50 mm thick, mounted on 6mm thick ac pain buildingboard or commercial plywood and fixed to wall with wooden plugs and chromium plated brass screws & cup washers complete all as specified and as directed. 120 s&f 4 mm thick one side frosted sheet glass ordinary quality and glazing in square n.exc 0.5sqm in each pane fixed with neopunerubber gasket in aluminium frame complete all as specified. 121 construction of guard post ( sewage disposal ) excavation over areas, not exceeding 1.5 m depth and getting out in soft / loose soil complete all as specified & directed. 122 excavation over areas, exceeding 1.5 m and not exceeding 3.00 m in depth and getting out in soft / loose soil completeall as specified & directed. 123 s&f 150mm bore reinforced concrete pipes, classnp 2 with one collar per length of pipe complete all as specified & directed. 124 m&l for cement concrete type d 2 ( 1:4:8 ) bed to drain pipes of 150 mm bore including packing under, and hunching against the sides of pipes after they are laid and tested in completeall as specified & directed. 125 m&l forbrick work with sub class b bricks built in cement mortar 1:4 straight or curved on plan etc. 6 mtr mean radius as in complete all as specified and directed. 126 m&l for 15 mm thick rendering in cement mortar ( 1:4 ) mixed with water proofing compound, on fair faces of brick or concrete surfaces, as in internal surfaces of manholes complete all as specified and as directed. 127 m&l for pcc, 1:2:4, type b 2 ( using 40mm graded stone aggregrates ) as in surface channel bed / drains / in manholes all as specified laid to slope and finished surface even and smooth complete all as specified & directed. 128 extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms moulds, metered / stopped ends etc. complete all as specified & directed. 129 m&l for precast rcc, ( 1:2:4 ) , type b 1 ( using 20mm graded stone aggregates ) as in cover slab, set in cement mortar ( 1:6 ) complete all as specified and as directed. 130 s&f 6 to 8 mm dia and over thermo mechanically treated ( tmt ) bars, cut to length, bent to shape required including cranking, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia complete all as specified and as directed. 131 m&l forbrickwork with sub class b bricks in one brick thick honeycomb walling built in cement mortar 1:4 complete all as specified and as directed. 132 construction of guard post ( external water supply ) supply and lay pipe galvanized, “medium class”, including fittings 40 mm dia complete all as specified and directed. 133 supply and lay pipe galvanized, “medium class”, including fittings 25 mm dia complete all as specified and directed. 134 s&f gun metal gate valve with iron wheel head, screwed both ends for gi steel pipe of 40 mm dia sizes complete all as specified and directed. 135 s&f gun metal gate valve with iron wheel head, screwed both ends for gi steel pipe of 25 mm dia sizes complete all as specified and directed. 136 drilling and tapping of ci water line 20 mm / 25mm for branch connection complete all as specified and as directed. 137 construction of guard post ( internal electrification ) m&l for point wiring with 1.5 sqmm ( 22 / 0.30mm ) pvc insulated andunsheathed multistranded copper conductor cable, 1100 volts grade, isi marked, frls type drawn through and including pvc concealed conduit ( isi marked ) of adequate size and its accessories with sunk cast iron / pressed steel terminal boxes of size 1.6mm thick, with 3mm thickplastic laminated sheet cover of adequate size for one light or one fan point controlled by one switch incl 1.5 sqmm ( nominalarea ) copper conductor cable ( multistrand ) , frls type, pvc insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metallic bodies of luminaires / fan at other end complete as per site requirement and all as specified & directed by engr in charge for one light point or one fan point controlled by one switch with cables 1.5 sq. mm size.note: unit rate include for cutting chases for conduits and sinking for boxes andmaking good to wall, floors etc. 138 all as per ser item no. 137 above here in before but for one 5 amp 5 pin socket outlet point on same board with other switches including earth wire as specified. 139 all as per ser item no.137 above, but for one 5 amp 5 pin socket outlet point on independent board. 140 all as per ser item no. 137 above, but with 4.0 sqmm ( 36 / 0.30mm ) pvc copper stranded cable frls type for one 15 amp 5 pin socket outlet point including pvc cable 4 sqmm frls type copper stranded conductor as earth wire as specified & connected to common earth & earth terminals including boards for mounting purposes. 141 s&f switch piano flush button 5 amp single pole one way 230 volts white finish all as specified & directed. 142 s&f switch socket combination flush type 5 pin 5 amp multipurpose 230 volts single pole one way suitable for 3 pin / 2pin 5 amp plug top white / ivory finish complete all as specified and directed. 143 s&f switch socket combination multipurpose flush type 2 in 1 type ( 3 and 5 pin ) 5 / 15 amps, 230v, ac complete all as specified and directed. 144 s&f ceiling rose surface pvc 50mm dia 3 terminals including pvc mounting block white / ivory finish complete all as specified and directed. 145 s&f led luminaire 600 mm x 600 mm, 35 / 36 watt, 220 v ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. 146 s&f stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd all as specified and directed of approved make. 147 s&f of submain wiring with two single core pvc insulated unsheathed, multistranded flexible copper conductor 1100volts grade, frls type, cables 6 sqmm drawn through in and including rigid pvc heavy duty concealed conduits including 6 sqmm 1100volts grade, frls type, pvc insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. note: ( i ) two runs of cables and one run of continuous earthing cable drawn in conduit will be measured as one length of sub main. ( ii ) pvc conduit and its accessories is deem to be included in this item rates. ( iii ) unit rate include for cutting chases for conduits and sinking for boxes andmaking good to wall, floors etc. 148 s&f distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & mcbs 240volts, 200 amp rated bus bar with front openable cover suitable for sp & n 8 ways all as specified & directed. 149 s&f mcb sp 6 32 amps / 40 amps, 230 volts, 50 hz with10 ka, c series all as specified & directed by engineer in charge. 150 s&f mcb spn / dp upto 32 amps, 230 volts, 50 hz with 10 ka, c series all as specified & directed by engineer in charge. 151 m&l earthing complete withgalvanised steel earth plate electrode 60cmx60cmx6 mm thickness burried directly in ground ( earth pit not less than 2.25mtr deep below normal ground level ) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl pcc pit of 1:2:4 type b 1, cover reinforced with xpm weightnot less than 4 kg / sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in anytype of soil, charcoal dust, salt, light grade gi watering pipe 20mm dia with funnel and wire mesh and medium grade gi protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete allto as shown in electrical plate no 3 of mes sch 2009 ( part i ) connected main switch board all as specified and testing on completion. 152 s&f new exhaust fan, steel body ac single phase. 230v of size 300mm sweep with, blades, and frame and louvers complete as per site requirement and all as specified and directed of approved make. 153 s&f ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep. min air delivery 210 cfm with service value 6.00 bee. five star rated with brushless direct current motor ( bldc ) all as specified as directed by engineer in charge. 154 construction of guard post ( external electrification ) supply lay / spread in trenches, river sand, clean, including spreading, levelling, punning as in cushioning of cables all as specified and as directed.note : punned depth will be measured and paid. 155 supply, lay in trenches fly ash bricks, old size for cable protection all as specified and directed. note: bricks shall be laid in such a way that its length is perpendicular to the length of cable. 156 supply, laying, connecting and testing lt ug cable frls xlpe insulated, armoured heavy duty electric cablewith aluminium conductor, 1100 volts grade sheathed, multi stranded of 16 sqmm 4 core cross sectional areacomplete all as specified and as directed : note : ( i ) lugs and glands are deemed to be included in the rate quoted for laying of cable and to be used properly wherever required while connecting cables to the panel board. ( ii ) earth work such as excavation, refilling, etc. shall be measured separately under relevant items. 157 notes : 1.the amount of schedule of credit shall be deducted from the total of this boq for arriving at contract sum....

Military Engineer Services - West Bengal

40191776 repair / replacement to joinery, false ceiling, wall linning, rolling shutter, door & window and miscb / r works at bsa complex, gokhale road, grand view, sky view and old imh complex under ge alipore kolkata; 1 taking down chowkhat with shutter ( without taking down shutters from the frame ) n.exc 1.5 sqm and removing from site complete all as specified and directed. 2 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified anddirected. ( upto 12 storied bldg ) . 3 taking down shutters of any description exc 1 sq. m but not exc 2 sq. m each complete all as specified and directed. 4 all as per item no 3 above here in before but exc 2 sqm each. 5 supply and fixingfor second class hard wood ( sal ) , plain, solid straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed ( upto 12 storied bldg ) . 6 supply and fixing for 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type both sides ( isi marked ) all with 6 mm thick teak wood edging all round complete all as specified anddirected ( upto 12 storied bldg ) . 7 supply and fixing for 35 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in ssr part i, section 8, clause 8.24 ( a ) , supplied and fitted to chowkhats complete all as specified and directed ( upto 12 storied bldg ) . 8 supply and fixing for factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading and joined together with solvent cement, and fixing in the frame at site complete all as specified and directed ( upto 12 storied bldg ) . 9 supply and fixing for solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s square tube, supplying & fixing in opening complete all as specified and directed. 10 s&f for factory made solid pvc moulded door shutter 28 to 30 mm thick ( stiles ) with 2 mm thick prelaminated moulded pvc sheet polyurethane painted on the front face& 2 mm plain colour pvc sheet on back faces, and with particle board core supplying and fixing in frame at site as per specification and drawing ( upto 12 storied bldg ) complete all as specified and directed. 11 supply and fixing for solid pvc door frame of size 50 mm x 47 mm made out of 5 mm single side prelam pvc sheet used instead of plain colour pvc sheet & edges will be painted to match, reinforced with ms sq tube in opening all as shown on drawing ( upto 12 storied bldg ) complete all asspecified and directed. 12 supply and fixing for windows with side hung shutter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. 13 all as per item no 12 above but without glazing bars. 14 supply and fixing steel ventilator with top hung shutter including hinges, steel peg stay complete including one shop coat primer all as specified and directed ( upto 12 storied bldg ) . 15 repairing and welding to steel doormaking functional ( easy to opening and closing ) and replacing the missing damaged parts complete all as specified and directed. 16 dismantling wrought iron or mild steel work of any description not otherwise provided for 17 supply and fixing for framed work such as grills to windows / ventilators, gratings etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framework of waste tanks and similar work conforming to fe fe 290 gde e 165 complete all as specified and directed. 18 s&f for powder coated aluminiumsliding windows for three track with rubber gasket, stopperpowder coated aluminium standard beads / glazing clips , locking arrangement etc and aluminium frame of size 80mmx25mmx1.55mm andshutter of section 20mm x20mm x1.55mm including ( two shutter of 4.8mm thick glass and one shutter of wiremesh 0.36 mm dia of wire and average width of aperture 1.40 mm ) including taking down old steel windows with all necessary fittings complete all as per manufacturers instructions and all as specified and directed. 19 s&f for power coated aluminium door shutter including door frame fixed including roller machinewith rubber gasket, stopper, cleats, handlesetc complete incl aluminium door styles of size 80 mm x 38 mm x 2.00 mm and aluminium doorsection of top, bottom and lock rail shutter frame of 80 mm x 38mm x 3.00 mm including taking down old door with necessary all fittingcomplete all as specified and directed. 20 s&f in repairs aluminium chequered grill fixed to aluminum section fixed to windows / shafts / openings with necessary all fittingcomplete all as specified and directed. 21 s&f in repairpower coated aluminium partition wall of framesize 80mm x 38mm x 2.00 mmwithstandard beads / glazing clips, locking arrangement etcwith necessary all fittings complete all as per manufacturers instructions and all as specified and directed. 22 s&ffor powder coated aluminium windows / ventilator fixed type , without sash bar weighing 0.55 kg / m including, necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws and taking down old window / ventilator complete all as specified and directed. 23 s&f for4.8 mmplain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area of glass not exc 0.5 sqm each pane complete all as specified and directed. 24 m&l for 9 mm thick prelaminated partilce boards interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screw to timber frame for pelmet boxes, aluminium door and aluminium partitionscomplete all as specified and directed. 25 dismantling of wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets complete all as specified and directed. 26 material and labour for 4mm thick non asbestus reinforcement gypsum ( grg ) ceilling tiles of size 595 x 595 mm of approved design fixed with powder coating ( powder coating on web bottom only ) gi grid consisting of main tee section of size ( 15mm x 30mm ) , cross tee section of size ( 15mm x 23mm ) , and powder coating gi wall angle of size ( 20mm x 20mm ) suitable for mounting ceiling tiles of 595 x595 mm with 4 mm dia gi wire suspended including fabrication complete as per manufacturers instructions fixed with steel rawl plug with nut and bolts arrangement with grid size 60 x 120 cm complete all as specified and directed.make : diamond brand tm / dexune / armstrong or equivalent approved by ge. 27 s&f in repair only 6 mm thick gypsumboard / tiles of size 600x600 mmincludingproper hanging arangementas required complete all as specified and directed. 28 m&l for 10 mm thick gypsum board false ceiling joint less work including application of putty over gypsum board to achieve smooth and joint less celing surface and applying two coats of oil bound distemper in ceiling surfaces including framed work forconsisting of 60 mm wide gi steel c section of as in main of 0.71mm thick and 60 mm gi channel section as in cross member of 0.63 mm thick and gi steel angle section as in suspenders of size 25x20x0.63 mm and wire cloth of 0.71 mm dia of wire and 100x50mm aperature size including cutting , riveting, steel fastener, drilling holes in rcc roof and securing with screws etc complete all as specified and directed. 29 m&l for pop cornice width n.exc 200mm wide in ceiling edge of any design and shape , complete all as specified and directed. 30 s&f in repair solid pvc wall lining consisting of 5mm thick plain colour pvc sheet inclusive of solvent cement and fixing at site on pvc frame including 5mm thick pvc fillets of width 35mm with grid size 500mm x 500mm in both horizontal and vertical directions including necessary caping / fillets at top and junctions required as per site etc complete all as per specified and directed. 31 taking down shutters of any descriptionexc. 1 sqm but n. exc. 2 sqm each and resecuring or easing & adjusting and refixing in same opening complete all as specified and directed ( upto 12 storey bldg ) . 32 s & f for stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanized wire staplesall as directed. 33 s & f in repair stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanized wire staples completeall as specified and directed. 34 m&l for hacking out old broken glass ( any thickness, size, quality or description ) from metal frame including punching or driling out old glazing pins / spring clips and providing and fixing new ones. 35 supply and fixing for 3mm thick sheet glass ordinary quality & glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and directed. 36 supply and fixing for 4 mm thick, sheet glass ordinary quality & glazingwith oil putty or aluminum clips, in squaresexc. 0.5 sqm in each pane complete all as specified and directed ( upto 12 storied bldg ) . 37 supply and fixing for figured glass 3mm thick, pin headed type & glazing with oil putty in squares notexc. 0.5 sqm in each pane complete all as specified and directed ( upto 12 storied bldg ) . 38 supply and fixing for mild steel of grade fe 290 in bands, straps, supports or stays for rain water, ventilating pipes including bolts, if required, clamps, hold fasts and similar small articles complete all as specified anddirected. ( upto 12 storied bldg ) . 39 supply and fixing for stainless steel butt hinges, medium weight, cold rolled of size 100 mm complete all as specified and directed. 40 supply and fixing fo 150 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed complete all as specified and directed. 41 supply and fixing for extruded aluminium alloy handles, 150mm long fabricated type, anodised complete all as specified and directed. 42 supply and fixing for 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified anddirected. 43 supply and fixing in repairsfloor door stopper of aluminium body and tongue anodised with hard drawn steel spring fixed in floor over all length of cover plate 150 mm complete al as specified and directed. 44 supply and fixing in repairs 300 mm long aluminium alloy anodised sliding door bolt with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified anddirected. ( upto 12 storied bldg ) . 45 supply and fixingin repairs 150 mm long aluminium anodised barrel tower bolt of extruded section. 46 supply and fixing in repair extruded aluminium alloy handles, 150 mm long fabricated type, anodised complete all as specified anddirected. 47 s & f in repairs aluminium body door closer hydraulically regulated, designation no. 3 universal type, suitable for door shutters of 851 1000 mm in width & weight between 61 to 80 kg complete all as specified anddirected. 48 s & f in repairsdouble action door spring hydraulically regulated made up of 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified anddirected. 49 supply and fixing as in repair mortice lock set combipack with 6 lever and with decorative type handle set complete all as specified and directed.make : godrej cat no 8286 or equivalent as approved by ge. 50 s&f in repair 5 mm thick beveled edge best quality looking mirror of size 600x450 mm fixed with screwscomplete all as specified and directed. 51 s&f in repair mirror cabinet best quality fixed with screws etc complete all as specified and directed. 52 dismantling boarding, any description, fixed in any position with nails etc complete all as specified and directed etc ciomplete all as specified and directed. 53 supply and fixing for 2nd class soft wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area exc 13.00 sqcm but n.exc 25.00 sqcm complete all as specified and directed. 54 supply and fixing for 2nd class soft wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area exc 3.00 sqcm but n.exc 6.00 sqcm complete all as specified and directed. 55 supply and fixing for 18 / 19 mm thick prelaminated particle board, exterior grade, fixed with screw to timber frame work but prelaminated both sides with decorative choice laminations complete all as specified and directed. 56 supply and fixing for hasp and stable 100 mm, aluminium anodised, wire type, stove enamelled black including bolt to hinge plate and fixed with screw etc complete all as specified and directed. 57 supply and fixing continuous ( piano ) hinges, mild steel, bright finish or electro galvanished width of flaps 40 mm ( when open ) complete all as specified and directed. 58 s&f in repair 40 mm knobs of brass, polished fixed with nut screw & washer bright finished complete all as specified and directed. 59 s&f for ball catcher with 8 mm dia steel ball and brass body and skirting plate including leting in and fixed complete all as specified and directed. 60 supply and fixing for 16 18mm thickplywood boards, grade 2 quality, interior grade, with decorative face veneer on bothface fixed with screws to timber frame work as in cupboard shutter including external teak wood lipping 6mm thick fixed with nails complete all as specified and directed . 61 supply and fixing in repair for 0.9mm thickess of decorative laminated type 1 of surfaces finish, colour and pattern as approved fixed with approved adhesive as per manufacture, s instruction complete all as specified and directed . 62 demolition of brickwork built in cement mortar bedding including all quoins, arches, pillars, etc. of any descriptions complete allas specified and directed. 63 material and labour for brick work with sub class b brick straight of curved on plan exc 6m mean radius built in cm ( 1:6 ) complete allas specified and directed. 64 all as per item no 63 above but except brick complete all as pecified and directed. 65 material and labour for brick work with sub class b bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar ( 1:4 ) complete allas specified and directed. 66 taking down cement plaster of any description, including racking out joints, hacking for key, scrubbing down with water etc including necessary arrangement forworking platform complete all as specified anddirected ( upto 12 storey bldg ) . 67 material and labour for 15mm thick rendering in cement mortar ( 1:6 ) on other than fair faces of brick work or concrete surfaces finished even and fair with out using extra cement including necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 68 material and labour for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement including necessary scaffolding complete all as specified and directed. ( upto 12 storeys bldgs ) . 69 material and labour for rendering 10mm thick in cement mortar 1:3 in ceiling including necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 70 m&l for fixing chicken wire mesh to spalled rcc slab, column, beam etc and applying dubbing out average 10mm thick with cm ( 1:6 ) on irregular face of walls or ceiling surface, make rough to receive top coat of plastering etc complete all as specified and directed. ( upto 12 storey bldg ) . 71 material and labour for two coats of synthetic enamel painting to wooden surfaces ( frame & shutter ) over a coat of pink primerincluding preparation of wooden surface of any description, not otherwise descri bed, over 10cm width or girth complete all as specified and directed. 72 material and labour for two coats of synthetic enamel painting to steel surfaces ( frame & shutter ) over a coat of red oxideprimer including preparation of steel surface of any description, not otherwise descri bed, over 10cm width or girth complete all as specified and directed. 73 material and labour for applying 2mm thick birla wall care putty or equivalent ( each layer n.exc 1mm thick ) on new plastered surfaces ( ceiling / wall ) etc including necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 74 material and labour for two coats acrylic distemper ( white or coloured as per site reqmt ) on new or previously untreated plastered surfaces including preparation of surface and necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 75 material and labour for preparation of newor previously untreated surfaces of ceiling and applying two coats of white washincluding necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 76 material and labour for two coats of cement base paint ( white or coloured as per site reqmt ) overnewly plastered surface of wallincluding preparation of surface and including necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 77 material and labour for onecoat of white wash on old decorated surface of wall including preparation of surfaces and necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 78 all as per item no 77 above but on ceiling complete all as specified and directed. 79 material and labour for onecoat of acrylic distemperon old decorated surface of internal walls including preparation of surfaces and necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 80 material and labour for onecoat of cement base paint ( white or coloured as per site reqmt ) on old decorated surface of external walls including preparation of surfaces to remove all foreign materials including necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . note : no separate payment shall be made for colour of cement paint where required or directed by engineer in charge and cost is included in unit rate. 81 m&l for preparation of old decorated surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, etc and applying one coat of anti algae and anti fungal exterior grade weather coat paintcomplete all as specified and directed. ( upto 12 storey of bldg ) 82 material and labour for one coat of synthetic enamelled paint on old decorated wooden surface exc 10cm width or girth including preparation and necessary arrangement forworking platform complete all as specified and directed ( upto 12 storey bldg ) . 83 m&l forpreparation of old steel surfaces of any descriptionover 10 cm width or girth and applyingone coat of synthetic enamel paintcomplete all as specified and directed. 84 demolition of pcc in ground floor and paving n. exc 15 cm thick ( below or above ground level ) including removal of debries to out side mod land complete all as specified and directed. 85 m&l for 75 mm thick pcc ( 1:4:8 ) , type d 2 ( using 40 mm graded stone agregate ) , as in sub case for floors, complete all as specified and directed 86 m&l 25 mm thick pcc ( 1:2:4 ) , type b 0 ( using 12.5 mm graded stone agregate ) , in sub base for floors, complete all as specified and directed. 87 dismantling of floors health or walls tiling and stone floor including cement mortar bedded & removing serviceable tiles to storeand rubbies of the premises complete all as specified and directed. 88 material and labour for coloured joint free ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding screed bed 15 mm thick in cement mortar ( 1:4 ) complete all as specified and directed. 89 all as per item no 88 but on vertical surface such as skirting, dado, riser over a backing coat of 10 mm thick screeding in cm ( 1:3 ) complete all as specified and directed. 90 m&l for coloured glazed ceramic tiles in vertical surfaces 350x250x7mm / 450x300x7mm thickness as per manufacture on vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm in cm ( 1:3 ) backing of tiles complete all as specified and directed. 91 m&l for light shade vitrified ceramic tiles 8 9mm thick ( square / rectangular ) polished area of each tiles not exceeding 0.36 sqm as in floor set and jointed in neat cement slurry and pointed white or coloured cement to match the shade of the tiles laid over and including 15mm thick screed bed in cm ( 1:6 ) etc complete all as specified and directed . 92 m&l for light shade vitrified ceramic tiles 8 9mm thick ( square / rectangular ) polished area of each tiles not exceeding 0.36 sqm as in skirting etc. set and jointed in neat cement slurry and pointed white or coloured cement to match the shade of the tiles laid over and including 10mm thick cement plaster in cm ( 1:4 ) for backing coat etc complete all as specified and directed . 93 m&l for plain cement concrete ( 1:2:4 ) type b1 ( using 20mm graded stone aggregate ) in copings, kneelers apex stones, bed plates, kerbs, water troughts and the like including weathening, slightly rounded or chamfered angles and throating as directed all as specified and directed. 94 material and labour for20 mm thick for pe polished chequered / pavments tiles glossy finish of size n. exc 0.16 sqm thickness, 10 ton capacity as in floor set and jointed in neat cement slurry and pointed in white cement with pigment to match pigment to match shade of the tiles over andincluding 15mm thick screed bed of cm ( 1:6 ) etc complete al as specified and directed. 95 material and labour in repairfor granite slab ( of any type ) 16 to 18 mm thick work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms over and including 15mm thick screed bed in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match withshade complete all as specified and directed. 96 drilling holes for bolts, pipes, etc. n. exc 25mm dia upto 10 cm depth in granite or trape stonefor gas connection pipe complete all as specified and directed. 97 rounding to edges of stone slabs one edge, such as in steps, cooking platfrom and other similar situations. 98 taking down eaves gutter, rain water pipes ( any size and pattern ) including all fitting, bends, shoes, swan neck etc including cleaning refixing and removing to store etc complete all as per specified and directed. 99 supply and fixing for pvc ( swr ) pipes of 110 mm dia, single socketed fixed to walls with necessary clamps complete all as specified and directed. 100 supply and fixing for pvc ( swr ) pipes of 75 mm dia, single socket fixed to walls with necessary clamps complete all as specified and directed. 101 supply and fixing for pvc ( swr ) junction single tee equal or unequal 110 mm dia with access door complete all as specified and directed. 102 supply and fixing for pvc ( swr ) junction single tee equal or unequal 75 mm dia with access door complete all as specified and directed. 103 supply and fixing for pvc ( swr ) bends of 110 mm dia of any radius complete all as specified and directed. 104 supply and fixing for pvc ( swr ) bends of 75mm dia, any radius complete all as specified and directed. 105 supply and fixing for 110 mm branch piece, single ( single y ) equal or unequal 106 supply and fixing for 75 mm branch piece, single ( single y ) equal or unequal 107 s&fin repair for 20 / 25mm high strength aluminium powder coated drapery rod fancy type including brackets and kobs etc complete all as specified and directed ( upto 12 storied bldg ) . 108 supplying and fixing in repair 1.25mm thick steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed. 109 oiling / greasing existing rolling shutters for easing adjusting for smooth functioning of steel rolling shutter complete all as specified and directed. 110 s&f for lock plate bracket made of angle 40x40x5 mm, flat 25x6 mm, cleat, latice flat & locking arrangement etc of rolling shuttes including necessary welding / riveting and one coat of red oxide primer including taking down old lock plate complete all as specified and directed. 111 s&f for mild steel slot profiles of 1mm thick including taking down old profiles complete all as specified and directed. 112 supplying and fixing in repair collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, rected in position and securing runners with holdfasts and brackets, complete all as specified and directed...

Department of Defence Production - West Bengal

40175449 bids are invited for aluminium alloy tube to is 738 desgn 24345 w or 64430 wp condition id 108mm od 90mm length 480mm (q3) , al alloy tube to is 738: 1994 desgn 24345 w or 64430 wp condition, id= 108mm od= 90mm l= 260mm (q3) total quantity : 979...

West Bengal Electronics Industry Development Corporation Limited - West Bengal

40166923 proposed extension of snltr office module at 6th floor in moni bhandar building , civil & interior works , 15mmthick ( average ) cement plaster l:6 ( 1 cement : 6medium sand ) to uneven surface, walls ( risers or set back ) , inside of the masonry surface, beams & column flushed with brick wall including extra thickness of mortar due toinequalities of brick work & extra cement required for plastering tor.c. surface, rakingout joints including the cost of chiselingtheundulating surface of brick masonry or chipping out r.c surface where necessarycomplete in all respects as per specification including necessary scaffolding etcwith all labour and materials to all floors. , providing and applying two coats of plastic emulsion paint of approved shade and quality over a coat of cement primer i including ) of approved quality on wall, column, beams, ceiling etc over pop surface including preparation of surface as per direction including providing necessary putty work, scaffolding etc complete with all labour and materials in all floors. work should be executed as per manufacturers specification. , painting two or more coats of approved synthetic enamel paint over a coat of approved primer ( including ) suitable as per manufacturers specification to achieve the desired finish over wall surface / wooden surfaces / other surfaces after preparation of surface properly as per direction with all labour and materials. the item is to be completed in all respects as per directions with all labour and materials. , joinery surface , steel surface , wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, iron butt hinges and m.s clamps. ( the quantum should be correted upto three decimals ) . sal local. at any floor & any location. , wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, iron butt hinges and m.s clamps. ( the quantum should be correted upto three decimals ) . 1st class best indian teak. at any floor & any location. , supplying, fitting and fixing boiling water proof ply conforming to is: 710 1977 bonded with phenol formaldehyde synthetic resin conforming to is: 848 1974 of approved make and brand fitted and fixed as per design as direction of engineer in charge. [ excluding the cost of supporting frame work per approval and and teak wood batten / lipping ] at any floor & any location. , 6mm , 9mm , 12mm , 19mm , supplying, fitting and fixing boiling water resistant ply conforming to is: 303 1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of engineer in charge.at any floor & any location. , 9mm , 6mm , supplying, fitting & fixing of aluminium fixed partion wall of all aluminium sections viz top, bottom and side member, intermediate member, glazing clip made of aluminium alloy extrusions conforming to is: 733 1983 and is: 1285 1975, annodized conforming to is:1868 1983, fitted with all other accessories viz. epdm gusket, cleat, angle screws etc. including labour charges for fitting and fixing of aluminium fixed partition wall with glass / panel board all complete as per architectural drawings and direction of engineer in charge. ( excluding cost of glass / panel board, 10 12 micron thickness annodizing film. natural white. , a ) for unsupported length of vertical member upto 1.50m. height of both ends of vertical member restrained but panel with in 0.90 sqm , b ) for unsupported length of vertical member above 1.50m. height of both ends of vertical member restrained but panel above 0.90 sqm , providing and laying 50mm thick expanded polystyrene block ( self extinguishing type ) having density 34.00kg / cum, thermal conductivity 0.28 w / m k, water absorption 0.1% ( maximum to be laid inside the partition wall by adhesive / fasteners as per manufacturers specification and specific direction, complete with all materials and labour. , partition of teak veneer as per design fitted and fixed complete ( excluding the supporting frame work ) . 4mm thick commercial quality. at any floor & any location. , supplying solid flush type doors of deluxe decorative ( both side ) quality, conforming to i:s 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings in any floor: ( a ) 35mm thick shutters ( single leaf ) , providing, fitting and fixing in position frameless fully glazed composite door fixed to the lintel and floor fitted with necessary ss patch fittings with double action floor spring including providing 12 mm thick toughened float glass of special selected quality free from bubbles, holes or any surface deformation. allow for cutting, chase to walls, lintel and floor and mending good damages. the rate shouldinclude for providing necessary approved qualitylocks, handles etc complete inall respects withnecessary patch fittings & fixtures, stainless steel pivot support as per drawing and direction with all labour and materials. a ) sliding / swing ( door ) with necessary top and bottom channles and slidders with a provision of movement sensor. ( sensor to be paid separately ) . , french polishing to wood work including preparing surface. high gloss polish with lacquer finish. on new wood work. at any floor & any location. , supplying fitting, fixing decorative lamination conforming to is: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on particle / mdf / ply boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of engineer incharge. the rate includes the cost of labour, adhesive and all incidental charges thereof. glossy / matt / suede excluding surface texture or metallic lustre. thickness of laminate 1 mm. at any floor & any location. , supplying, fitting and fixing 8mm thick laminated wooden flooring work conforming to en13329:2006 with plank size not iess than 1200 mm x 190 mm ( with unilin / tongue groove locking arrangement ) having 0.2mm thk top abrasive layer over a decorative layer followed by a high density fibreboard ( hdf ) having density > 850 kg / m3 substrate core over a rasin saturated backing layer and installing through unilin or tongue groove system ( having locking strength not less than 1000 kg / m ) over a 2 mm thk underlayer polyurethene foam on polythene sheet 250 micron, over a smooth, flat, hard subfloor free from moisture ( < 8% ) , grease etc. complete in all respect with requisite accessories like end profile, transition profile, reducer t profile etc. wherever required and preparation of base including all other incidental works as per direction & satisfaction of engineer in charge. cost of laminate floor accessories only ( skirting , end edge, t moulding, reducer ) shall have to be added separately, wherever required. category: normal footfall; class 23;abrasion resistance: ac3 thk on swelling: < 18% ;impact resistance: ic 1 , providing and fixing of false ceiling with powder coated exposed g.i. grid suspension system ( e grid u 1520 or equivalent load carrying capacity with mid span deflection not exceeding 1 / 360 span with hanger spacing of 1200mm c / c ) consisting of main runner 3600 mm long, cross tee 1200 mm / 600 mm long and wall angle. the wall angle shall be fixed on pvc dash fasteners on the perimeter of the wall by steel screws with distance 300mm c / c. the main runners to be placed @ 1200 mm. the cross tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm. additional cross tees of 600 mm shall be placed perpendicular to the cross tee 1200 mm long to finally form a grid of 600 mm x 600 mm. grid of module size 600 mm x 600 mm shall be supported by 6 mm diag.i. wire from purlins / soffit. 15mm thick ow acoustic board ( mineral fiber acoustic ceiling tiles ) of approved patern and size 595mm x 595mm with nrc value > 0.65 should be placed in the grid module to form a false ceiling. all complete as per the drawing & directions of engineer in charge. in any floor. , rendering the surface of walls and ceiling with white cement base water proof wall putty of approved make & brand. ( 1.5 mm thick ) , chair providing & installation of mid back chairs with mesh for back & seat in fabric, tilting back rest, fixed armrests with cantilever base and castor. , supply, fitting & fixing of magnetic lock. as per approved brand. , supply, fitting & fixing of cabinet lock. as per approved brand. , anodised aluminium barrel / tower / socket bolt ( full covered ) of approved manufactured from extruded section conforming to i.s. 204 / 74 fitted and fixed with cadmium plated screws: 100mm long x 10mm dia. bolt. as per approved brand. , supplying, fitting and fixing ss hinge cleat in position excluding the cost hinge and other fiffitngs. 50mm , iron butt hinges of approved quality fitted and fixed with steel screws, with isi mark. ( i ) 100mm. x 50mm. x 1.25mm. , supply, fitting & fixing of telescopic channel for drawer fixing purpose. as per approved brand. , anodised aliminium d type handle of approved quality manufactured from extruded section conforming to i.s. specification ( i.s. 230 / 72 ) fitted and fixed complete. without base. 100 mm grip x 10 mm dia rod. as per approved brand. , supply, fitting & fixing of autoclosing hinges for cabinet shutter. as per approved brand. , supply, fitting & fixing of venetian blind with necessary frame work for glass windows. as per approved brand. , hydraulic door closer of approved quality as per i.s.i. standard fitted and fixed complete. godrej hydraulic door closer fitted and fixed complete. heavy type. , supplying, fitting & fixing stainless steel d or h type of size 300 mm x 19 mm tubular handle with grade 304, ce certified, marked & conforming to en 1154, of approved quality of reputed brand as per direction of eingineer in charge fitted and fixed complete including all incidental charges. , supply fitting & fixing of door stopper ( brass ) . as per approved brand. , supplying mortice lock chromium plated with keys 6 levers including fitting & fixing complete. , dismantling the existing false ceilingboards and its frame work and removing & stacking the same as per direction of onwer. , removing carefully existing plaster / skirting of any thickness as per direction from wall, ceiling etc including preparation of surface to receive new plaster, removing debris from work site. complete with all labour and materials in all floors. , taking out carefully existing partition with frame, aluminium doors , floor springs, loose furniture ( cheir , table, cup boards, computer etc. ) , shiftring to 7th floor and stacking properly for re use . all surplus materials debrish shall be remove d at any suitable place as per direction of owner , payment will be made as per floor area , taking out carefully existing collapsible gate / grills and refixing the same in position after repairing and painting including preparation of surface the same as per direction to match with existing gate complete with all labour and materials. , electrical work , mcb distribution board , supplying and fixing of surface / flush mounting double door vertical tpn mcb distribution board for mcb db with ip 42 / 43 protection, concealed in wall after cutting the wall & mending good the damages to original finsh incl. inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. the rate shall include necessary civil work for installation as required. , up to 160a , 6 way enclosure ( ltvd06mgn ) , sit & c of surface / flush mounting of double door horizontal tpn mcb distribution board with ip 42 / 43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. the rate shall include necessary civil work for installation as required. , 4 way enclosure ( 607715 ) , sit & c of surface / flush mounting of double door spn mcb distribution board with ip 42 / 43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. , 2+8 way enclosure ( 607711 ) , mcb , supplying and fixing 240 / 415v mcb of breaking capacity 10ka & c characteristics on din rail of existing dbs and necessary connection as required , 6 32a sp , 6 32a dp , 6 32a tp , 6 32a fp , 63a fp , surge protective device , supplying and fixing class 2 ( t2 ) 415v, fp surge protective device ( spd ) of imax 40ka / pole mounted on din rail of existing dbs and necessary connection , mcb enclosure box for ac odu , supplying and fixing of 6 32a fp isolator with metal enclosure ( outdoor type ip65 ) near ac odu ( concealed / surface ) & mending good the damages to original finish including painting, connection & provision for earthing attachement. , supplying and fixing of 6 32a dp isolator with metal enclosure ( outdoor type ip65 ) near ac odu ( concealed / surface ) & mending good the damages to original finish including painting, connection & provision for earthing attachement. , mv cable , supplying, laying, testing and commissioing of 1.1kv grade, a2xfy xlpe armoured aluminium cable of following size with all necessary accessories required for installation on the wall above false ceiling and concealed / surface on wall below the false ceiling, rate shall include with 2 nos. 10 swg gi earth continuity wire for running earth and all civil work like cutting dressing mending good damages as required. , 4 core 25 sqmm , cable end termination , supplying and fixing double compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture proof entry of xlpe armoured cable as below: , 4 core 25 sqmm , finishing the end of following xlpe armoured cables by crimping method incl. supplying and fixing solderless socket ( dowels make ) , tapes, anticorrosive paste & jointing materials: , 4 core 25 sqmm , sub mains / circuit mains , wiring with pvc insulated & unsheathed single core stranded copper wire ‘fr – in pvc rigid / flexible conduit fr ( isi marked ) on wall / ceiling / furniture as per site requirement ( concealed / surface ) , supplying & drawing of wiring in 11kv single core stranded fr pvc insulated & unsheathed copper wire in 20mm size pvc rigid / flexible conduit ( as per direction by eic ) fr including neccessary fittings and neccessary connections as required , 2 x 36 / 0.3 ( 2.5 sqmm ) + 1 x 22 / 0.3 ( 1.5 sqmm ) ecc. , 2 x 56 / 0.3 ( 4 sqmm ) + 1 x 36 / 0.3 ( 2.5 sqmm ) ecc. , supplying & drawing of wiring in 1.1 kv single core stranded fr pvc insulated & unsheathed copper wire in 25mm size pvc rigid / flexible conduit ( as per direction by eic ) fr including necessary fittings and necesaary connections as required , 4 x 56 / 0.3 ( 4 sqmm ) + 2 x 36 / 0.3 ( 2.5 sqmm ) ecc. , 4 x 84 / 0.3 ( 6 sqmm ) + 2 x 56 / 0.3 ( 4 sqmm ) ecc. , wiring with pvc insulated & unsheathed single core stranded copper wire ‘fr – in pvc casing cappingon wall / ceiling / furniture as per site requirement , supplying & drawing of wiring in 1.1 kv grade single core stranded fr pvc insulated & unsheathed copper wire of following sizes in 25mm pvc casing capping ( as per direction by eic ) including necessary pvc clips, fittings, necessary connections as required , 2 x 36 / 0.3 ( 2.5 sqmm ) + 1 x 22 / 0.3 ( 1.5 sqmm ) ecc. , point wiring , supplying and carrying wiring for light, fan and dependent socket points by using 16 swg ms / pvc conduits with threaded joints of required dia as per is 732, ms / pvc conduit accessories, ms / pvc flexible conduit with couplers for drops with accessories, 2 x 1.5 + 1 x 1.5 sq mm, 1100v grade frls pvc insulated copper wires approved 6a modular type switches and sockets with plates and all accessories for fixing in modular furniture, gi / pvc boxes and other point wiring accessories and carrying out surface / concealed conduit system of wiring as per requirement with all wiring materials. conduits shall run on surface of the ceiling above false ceiling and concealed in wall by cutting chase in wall and mending good of all the damages. all points shall be earthed with 1.5 sq mm frls flexible copper wire. wires shall be terminated at light fixtures with ferrules, 16a, 4 way connector, wire ends shall not be kept loose / bare. the rate shall also include all accessories of ms / pvc conduits, etc, necessary civil works for embedding conduits and boxes below false ceiling, wherever applicable. , 1 light point controlled by 1 no. 6a switch , 2 light points controlled by 1 no. 6a switch , 3 light points controlled by 1 no. 6a switch , fan point controlled by 6a switch & ceiling rose near fan , switches & sockets , sit & c of the following components like approved plate type modular switches, socket etc. duly wired. , 1 no. 6 / 16a, 6 pin in universal socket controlled by 16a, sp switch, rp in workstations and in cabins, with ms / pvc box. , same as above but without ms / pvc box , 3 nos 6a, 5 pin socket controlled by common 16a, sp switch, workstations without ms / pvc box , same as above but with ms / pvc box , 1 no. 6a, 5 pin in universal socket controlled by 6a, sp switch, for wi fi with ms / pvc box. , ac sockets & starter , supply and flush fixing of modular type heavy duty plug socket unit comprising of 16 / 25a socket and plug top ( with indicator ) and solid state type starter units of electronic type with highflow voltage protections, o / l protect etc and suitable for ac units modular type and completely wired including cutting chases and mending good damages, painting, earthing, neccessary connections complete, as per required for ac units. , empty conduits , supply and fixing of frls pvc ( isi marked ) conduit ( rigid / flexible ) of various dia, exposed or concealed with all accessories like tees, bends, glands etc. jbs ( pvc ) as required and fish wire etc for wiring purpose complete and mending good damages to building works. , 20 mm dia ( 2 mm thick ) , 25 mm dia ( 2 mm thick ) , supplying and fixing pvc casing capping on wall or ceiling, including elobw, necessary pvc fittings etc. amd mending good damages to building works , 20x10 mm size , suplying and fixing of 5.5 x 5.5 sheet steel cover on floor jb , light & fan fixture work , indoor type luminaire , supply, installation, testing and commissioning of light fixture complete with all fittngs & accessories, as required. erection rate shall include necessary gi chain and supporting suspending hardware for fixing the light fittings. , recessed mounted led light fixture ( philips rc380b led36s 6500 g6 l60w60 psu od ( fullglow ) or similar approved equivalent ) . , recessed mounted down light 20w round led light fixture ( philips dn296b led20s 6500 psu wh or similar approved equivalent ) . , wall mounting fan , supply, installation, testing & commissioning of decorative wall mounted oscillating type fan with inbuilt speed controller. the rate shall be inclusive of fixing & mounting accessories and making necessary connections as required. fixing only cabin fan on wall / ceiling by s&f rag bolts, nuts & washers ( 6 mm dia x 62 mm long ) or as reqd. incl. s&f 24 / 0.20 pvc insulated flexible copper wire 0.5 mt. length , 450mm sweep wall fan. ( havells airboll hi speed or similar approved equivalent ) , dismantling / removal , dismantling / removal of existing light fittings, switch boards, conduit etc. , cassette type split ac , supply, installation, testing & commissioning of air cooled cassette, non inverter split type air conditioning machines of following cooling capacities with rotary / twin rotary type compressor. the condenser will comprise of copper tube aluminium finned coil with safety controls and refrigerant gas r32 / r 410a gas as required. , 2.0 tr 2 star , 3.0 tr 2 star , refrigerant piping , supply and installation of soft drawn refrigerant piping for the abovementioned cassette a.c. units including nitryle rubber insulation. , cabling , supply and installation of electricalpower / control cablingof suitable size between indoor units and outdoor units. , 4c x 2.5 mm , drain piping , supplying and laying of condensate drain line withpvc pipe complete with all accessories with 6mm nitryle rubber insulation. , 25mm , 32 mm , odu structure , supplying and installation of ms fabricated odu angle ( 50x50x6 mm ) structure for installation of out door unit with all accessories including ribbed neoprene vi pads, painting two coats with synthetic enamel paint over a coat of red oxide primer etc for cassettes. , misc ac work including civil work for breaking wall for copper pipe, cable & drain water line, scaffolding / lifting etc and mending good damages complete. , dismantling of existing 17 tr ac machine ( idu & odu ) , ac pipes, ducts, diffusers, cables etc. and storing the same carefully as directed by e.i.c. , fire work , dismantling carefully the existingfire sprinkler from old false ceiling, storing the same carefully and fixing the same in new false ceiling with necessary clamps etc. complete , dismantling carefully the existing smoke detector from old false ceiling, storing the same carefully and fixing the same in new false ceiling with necessary wire etc. complete. , supply and fixing fire exit signage ( i.e., fire exit ) in aclyric sheet with vinyle painted with all accessories complete.size shall be 6x12 , dismantling the existing 6w speaker and reinstallation of the same in new false ceiling with necessary fittings as complete. , sitc of 15 mm size quartz bulb type fire sprinkler of rating 68 deg.c with required accessories. as complete. , 65 inch. interactive flat panel with trolly incl. octacore processor / 8gb ram / 32gb storage / 2*16w speaker / 3 years warranty / hdmi cable / display adapter...

Urban Local Bodies - West Bengal

40101302 construction partition wall by aluminium alloy extrucsion and acp for north side ground floor office building at halisahar municipality, ward no. 06 under halisahar municipality....

South Eastern Railways - West Bengal

40003217 supply of manufacturing, supply, installation and fixing made by supplier of t/p boardmanufacturing, supply, installation and fixing made by supplier of t/p board,manufacturing, supply, installation and fixing made by supplier of t/p board at jurisdiction of adra division , sizes of irpwm, made out of 2 mm thick aluminium alloy sheet conforming to i.s. 736 with back support of galvanized angle 25x25x3 mm. the entire face of the board shall be covered with yellow high intensity encapsulated retro reflective sheeting with hlva process. the letters shall be cut out of black high intensity encapsulated sheeting and provided on the base sheet with hlva process. the board shall be fixed with ms angle of suitable size. [ warranty period: 30 months after the date of delivery ] => limited...

Technical Education and Training Department - West Bengal

39918568 supply, testing, installation, commissioning &demonstration of hand tools, instruments & different machineries / equipment for driver cum mechanic ( lmv ) trade , hammer ball peen, 0.75 kg. , chisel cold flat, 19 mm. , centre punch, 10 mm. dia x 100 mm. , steel rule 15 cm, english and metric, 15 cm ( steel metal ) , screw driver, 30 cm x 9 mm. blade, ( other side star head ) , screw driver, 20 cm x 9 mm. blade, ( other side star head ) , spanner de, set of 12 pieces, 6 mm 32 mm ( drop forged ) , plier combination, 15 cm , hand file 20 cm second cut, , feeler gauge ( metric ) , 20 blades, 0.05 mm to 1 mm, mat stainless steel , ring spanner, set of 12 pieces, 6 mm 32 mm , steel tool box with lock and key ( folding type ) , size 400 x 200 x 150 mm. , allen key, set of 12 pieces, 2 mm. 14 mm , circlip plier ( ext. ) , 150 mm. , circlip plier ( ext. ) , 200 mm. , circlip plier ( int. ) , 200 mm. , circlip plier ( int. ) , 150 mm , philips screw driver type set of 5 pieces, 100 mm to 300 mm , socket spanner ( 1 set of 12 nos. ) , 6 mm to 32 mm with handle in a box. , jack light type, 2 ton sessor jack with handle , jack heavy type, 5 ton hydraulic bolt and jack , wheel wrench singlebar, wrench single: size 19 mm, handle 18.9 cm , wheel wrenchcross bar, cross bar 17×19 mm, 18× 21 mm socket , light motor vehicle: dimensions: length 3655 mm, width 1620 mm, height 1675 mm wheelbase 2435 mm, turning radius 4.7 m. engine & transmission: capacity 998 cc, number of cylinders 3, fuel petrol.maximum engine output ( kw @ rpm ) 49.0 kw ( 66.62 ps ) @ 5500 rpm, maximum torque ( nm @ rpm ) 89.0 nm @ 3500 rpm, transmission manual. seating capacity 5, boot space 341 l, wheels & tyres: size 165 / 70r14, type radial & tubeless, steel wheels, brakes: front disc, rear drum, kerb weight 825 kg, ( special instruction: double clutch & brake, driving training vehicle ) new vehicle, bs 6 compliant.manufacturer must have service centre at howrah west bengal. , driving simulator:advance three screen car driving simulator, reputed manufacturer genuine parts stearing system, clutch, brake, gear system etc. computer and software requirement : processor i3 12th generation, ram 8gb, nvme 500 gb nvme , graphic card 550 × 4gb, smps 250 w, wireless key board mouse, speakers, wifi, os win 10 pro 64 bit, 24 × 24 × 24 full hd screen monitor. indian scheenario based driving training , light motor vehicle:body type: hatchback dimensions : length 3815, width 1680, height 1520, wheelbase 2450 engine & transmission: engine type 1.2 kappa drivetrain fwdfuel type petrol max power ( bhp@rpm ) 82 bhp @ 6000 rpm max torque ( nm@rpm ) 114 nm @ 4000 rpm engine 1197 cc, 4 cylinders inline, 4 valves / cylinder, dohc transmission manual 5 gears, emission standard bs 6 suspensions, brakes & steering: front brake type disc rear brake type drum steering type power assisted ( electric ) wheels & tyres: wheels steel rims spare wheel steel front tyres 175 / 60 r15 rear tyres 175 / 60 r15new vehicle, bs 6 compliant.manufacturer must have service centre at howrah west bengal. , traffic signal board , fire extinguisher :capacity 1 kg fire rating 1a, 8b material construction: cylinder body m.s, control valve brush, syphon tube cpvc / aluminum fitted with valve chemical charge map based dry powder, propellent nitrogen, class of fire a, b, cand e , fire bracket swing stand : suitable for lmv maintenance workshop , safety cones, ladwa 750 mm, plastic & rubberred, blue, orange, black , battery charger, 12 v to 36 v, 10 amp , oil can, 500 ml , adjustable spanner, 10? , adjustable spanner, 12? , grease gun, 1.5 kg capacity , safety stand, rod diameter 25 mm, lod length 711 mm ( 28 inch ) , rod material 304 stainless steel tube, weight 5 kg, material cast zinc aluminum alloy coated with chemical resistant epoxy paint , oil syringe, 500 ml , multi plug drain spanner, suitable for lmv , tyre lever, heavy duty ( for lmv ) , valve die, suitable for lmv...

South Eastern Railways - West Bengal

39877901 supply of manufacturing, supply, installation and fixing made by supplier of t/g boardmanufacturing, supply, installation and fixing made by supplier of t/g board,manufacturing, supply, installation and fixing made by supplier of t/g board at jurisdiction in adra division , sizes of irpwm, made out of 2 mm thick aluminium alloy sheet conforming to i.s. 736 with back support of galvanized angle 25x25x3 mm. the entire face of the board shall be covered with yellow high intensity encapsulated retro reflective sheeting with hlva process. the letters shalh be cut out of black high intensity encapsulated sheeting and provided on the base sheet with hlva process. the board shall be fixed with ms angle of suitable size. [ warranty period: 30 months after the date of delivery ] => limited...

South Eastern Railways - West Bengal

39846321 supply of installation and fixing made by supplier at jurisdiction of adra division caution indicator board of sizes of irpwm, made out of 2 mm thick aluminium alloy sheet conforming to i.s. 736 with back support of galvanized angle 25x25x3 mm. the entire face of the board shall be covered with yellow high intensity encapsutated retro reflective sheeting with hlvaprocess. the letters shall be cut out of black high intensity encapsulated sheeting and provided on the base sheet with hlva process. the board shall be fired with ms angle of suitable size. with 03 numbers extra plate of speed including. [ warranty period: 30 months after the date of delivery ] => limited...

Military Engineer Services - West Bengal

39843103 tender for spl repair to bldg no. p 95 ( or md accn ) at lebong under age ( i ) darjeeling.; 1 dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings, complete all as specified and directed. 2 s&f of pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed. 3 s&f of pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed. 4 add to item 2.00 & 3.00 here in before if fixed with l type or j type or cranked hook bolts in lieu of screw, complete all as specified and directed. 5 dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. 6 s&f of mild steel hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding inconcrete and screwing etc. wind ties for roof including securing bolts conforming to fe 290 gde e 165, complete all as specified and directed 7 s&f of framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to fe.290.gde e 165 ( brackets over 10 kg each to be measured under structural steel ) , complete all as specified and directed. 8 roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., complete all as specified and directed. 9 m&l for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar ( 1:6 ) finished even and rough, complete all as specified and directed. 10 m&l for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles, complete all as specified and directed. 11 m&l for non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles, complete all as specified and directed. 12 m&l for machine cut kota stone slab 20 25mm thickin riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed. 13 m&l for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigments, complete all as specified and directed. 14 m&l for rendering 10mm thick in cement mortar ( 1:3 ) on fair faces of brick work or concrete surfaces, complete all as specified and directed. 15 m&l for coloured glazed ceramic tiles in vertical surface 350x 250x 7 mm / 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface of tiles, complete all as specified and directed. 16 taking down cement or cement lime plaster, any description on brick or stone masonrysurfaces of walls etc includingrakingout joints, hackingfor key, scrubbingdown with wateretc, complete all as specified and directed. 17 m&l for rendering 15mm thick in cement mortar ( 1:6 ) on fair faces of brick work or concrete surfaces, finished even and smooth ( without using extra lime or cement ) , complete all as specified and directed. 18 m&l for rendering 15mm thick in cement mortar ( 1:4 ) with water proofing compound @ 3% by weight of cement or in the manner specified by the manufacturer and in the proportions indicated on fair faces of brick work or concrete surfaces, finished even and smooth ( without using extra lime or cement ) , complete all as specified and directed.note: water proofing compound will be measured and paid separately. 19 m&l for 5mm thick rendering in cement mortar ( 1:3 ) on concrete surfaces in ceilings and finished even and smooth ( without using extra lime or cement ) , complete all as specified and directed. 20 supply only integral water proofing compond, all as specified and as directed. 21 m&l for preparation of new plastered or unplastered surface of wall and applying two coats of distemper oil emulsion ( obd ) , over acoat of priming coat ( chalk whiting, on plastered surfaces, prepara tory to distempering ) including 3mm thick wall care putty on wall, complete all as specified and directed. 22 m&l forpreparation of new plastered or unplastered surface of ceiling and applying one coat of oil bound distemper ( distemper oil emulsion ) over a coat of priming coat ( chalk whiting, on plastered surfaces, preparatory to distempering ) including 1mm thick wall care putty on ceiling, complete all as specified and directed. 23 m&l forpreparation of new plastered or unplastered surface of wall and finishing walls with acrylic smooth exterior paint of required shade : new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) , complete all as specified and directed. 24 m&l for complete removal of existing treatment on plastered or unplastered surface of wall including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying one coat 1mm thick of wall care putty and then applying two coats of distemper oil emulsion ( obd ) , white or tinted over a coat of priming coat ( chalk whiting, on plastered surfaces, preparatory to distempering ) after preparation of wall surfaces, complete all as specified and directed. 25 m&l for complete removal of existing treatment on plastered or unplastered surface of ceiling including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying one coat of oil bound distemper ( distemper oil emulsion ) over acoat of priming coat ( chalk whiting, on plastered surfaces, preparatory to distempering ) including 1mm thick layer of wall care putty on ceiling after preparation of wall surfaces, complete all as specified and directed. 26 m&l for complete removal of existing treatment on plastered or unplastered surface of wall including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces, complete all as specified and directed. 27 m&l for preparation of old decorated plastered or unplastered surfaces of wall including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spot and applying and applying two coats of white wash on walls, complete all as specified and directed. 28 m&l for preparation of old wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed. 29 m&l for preparation of new wooden or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. 30 m&l for preparation of old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed. 31 m&l for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed. 32 taking up or downold 15 mm bore steel water tubing and connections, including cleaning for refixing or removal to store or from site, complete all as specified and directed. 33 taking up or down old 20 mm bore steel water tubing and connections, including cleaning for refixing or removal to store or from site, complete all as specified and directed. 34 s&f of 15 mm bore steel water tubes, medium grade, galvanised with and including all gi fitting ( such as bends, elbows, tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceilingor laid in / on floor, complete all as specified and directed. 35 s&f of 20 mm bore steel water tubes, medium grade, galvanised with and including all gi fitting ( such as bends, elbows, tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceilingor laid in / on floor, complete all as specified and directed. 36 refixing old 15 mm bore steel tubing and connections in new or old position ( walls, ceiling, floors, etc. ) , complete all as specified and directed. 37 refixing old 20 mm bore steel tubing and connections in new or old position ( walls, ceiling, floors, etc. ) , complete all as specified and directed. 38 s&f of 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. 39 s&f in repair of 15mm bore dia bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. 40 s&f in repairs of 15mm bore dia stop valves, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. 41 s&f of water closet ( squatt pattern ) of vitreous china squatting pan of pattern orrisa pattern size 580 x 440 mm white with integral foot rests ( excluding flushing cistern and flush pipe ) including connection to trap and flushing pipe anti syphonic pipe etc complete including p or s trap set in and including necessary lean cement concrete, complete all as specified and directed. 42 s&f of vitreous china wash down water closet pan ( pedestal pattern ) , white ( excluding fixing bolts, flushing cistern and flush pipe ) and making good the floor, complete all as specified and directed. 43 s&f of 100mm bore of pipe ‘p’ or ‘s’ traps without vent horn, complete all as specified and directed. 44 s&f of pvclow level flushing cistern 10 litre capacity, valveless syphonic action type complete with inlet, ball valve, float valve, bends brackets, rawl plug, brass screws handle etc complete having bis description mark with is:2731 with and including suitable size of ms brackets, plug, screw all as required incl taking down existing high level / low level flushing cistern any type disconnecting pipes and jointing with new one etc, and making good the floors / walls as per existing floor finish / wall finish including 32 mm bore pvc flush pipe and jointing with water closet of any type, complete all as specified and directed. 45 s&f of pvc connections 15mm size with ptmt nuts of length 450mm, all as specified and directed. 46 s&f of towel rail 450mm long of ptmt fixed with and including chromium plated brass screws and wooden / plastic cleats ( minimum weight 170gms ) , complete all as specified and directed. 47 s&f of grating doom 100mm dia of ptmt ( minimum weight 25gms ) , complete all as specified and directed. 48 s&f of 1mm thick stainless steel sink with drainage board kitchen or laboratory type with waste pipe, plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm, complete all as specified and directed. 49 dismantling water tanks of capacity exc 500 and n exc 1000 litres and removing to store, complete all as specified and directed. 50 s&f of rotational moulded polyethylene water storage tanks of capacity 1000 litres ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part l and directed. 51 s&f in repairs of 20 mm bore dia ball valves high pressure of ptmt with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. ( minimum weight 15mm 142gms / 20 mm 210 gms. / 25mm 455gms / 40mm 690 gms ) , complete all as specified and directed. 52 supplied and fixed in repair of 15 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. 53 supplied and fixed in repair of 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. 54 dismantling of wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and directed. 55 s&f of anodised aluminium snap grid frame work of size of grid 605mm x 605mm for false ceiling, complete all as specified and directed. 56 m&l for 4mm thick non asbestos fibre cement building boards fixed or laid / inserted to timber / gi / aluminium framework with screws in ceiling flat or sloping, complete all as specified and directed. 57 demolition and breaking up drain pipes ( pvc ( swr ) , salt glazed ware, ac or reinforced concrete ) of 150mm bore including accessories set in cement mortar and removing rubbish from site, complete all as specified and directed. 58 demolition and breaking up drain pipes ( pvc ( swr ) , salt glazed ware, ac or reinforced concrete ) of100mm bore including accessories set in cement mortar and removing rubbish from site, complete all as specified and directed. 59 m&l for 150mm internal diameter salt glazed stoneware drain pipes laid in trenches and jointed all as specified and directed. 60 m&l for 100mm internal diameter salt glazed stoneware drain pipes laid in trenches and jointed all as specified and directed. 61 m&l for plain cement concrete ( 1:4:8 ) bed, type d 2, ( using 40mm graded stone aggregate ) to drain pipes 150mm bore including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed. 62 m&l for plain cement concrete ( 1:4:8 ) bed, type d 2, ( using 40mm graded stone aggregate ) to drain pipes 100mm bore including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed. 63 dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and directed. 64 m&l for 100mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, complete all as specified and directed. 65 m&l for 100mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed. 66 s&f of 100mm bore dia cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) fitted with oval access doors, complete all as specified and directed. 67 s&f of 100mm bore dia cast iron cowls, complete all as specified and directed. 68 demolition of cement concrete ( unreinforced ) in ground floor and pavings not exc 15 cm thickness ( below or above ground level ) , complete all as specified and directed. 69 m&l for 75 mm thick plain cement concrete ( 1:3:6 ) , type c 2 ( 40 mm graded stone aggregate ) as in plinth protection, hard standing, path etc including finish the surface even and smooth without using extra cement, complete all as specified and directed. 70 m&l for 40mm thick plain cement concrete ( 1:2:4 ) , type b 1, ( using 20mm graded stone aggregate ) as in sub base, sub floors, floors, pavings, roof treatment etc., complete all as specified and directed. 71 m&l for hardcore using broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed. 72 demolition of brickwork or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed. 73 m&l for brickwork with fly ash bricks ( old size bricks ) , straight or curved on plan exc 6m mean radius, built in cement mortar ( 1:6 ) , complete all as specified and directed. 74 m&l for plain cement concrete ( 1:3:6 ) , type c 2 ( 40 mm graded stone aggregate ) in surface channels and drains, complete all as specified and directed. 75 m&l for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds mitered / stopped ends etc all as specified and as directed. 76 taking down chowkhatsor frame not exc 1.50 sqm each with shutter ( without taking off shutters from the frame ) , complete all as specified and directed. 77 taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters ( without taking off shutters from the frame ) , complete all as specified and directed. 78 taking down shutters of any description n exc 1 sq. m each, complete all as specified and directed. 79 taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each, complete all as specified and directed. 80 dismantling timber scantlings 40 sqcm and over in section, in any position ( unframed work ) , all as specified and directed. 81 s&f of second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. 82 m&l for preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with one coat of creosote oil, complete all as specified and directed. 83 m&l for second class hard wood, 35mm thick plain, framed, panelled shutters ( any number of panels ) , with panels of timber flat on both sides ( feather edged ) , or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed. 84 s&f of 35 mm thick ( batten thickness ) second class hard wood, glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc , divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded with cut mitred beds for securing glass etc, supplied and fitted to chowkhats completeall as specified and directed. ( note : the dimension of the various components or parts of shutters shall be as specified in clause 8.24 ( a ) of mes ssr 2009 part i ) 85 m&l for second class hard wood, 30mm thick glazed and skeleton windows shutters, ventilators shutters etc. are provided with stiles and rails, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in ssr part i, section 8 clause 8.24 ( b ) ; supplied and fitted to chowkats, complete all as specified and directed. 86 s&f of solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. 87 s&f of factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing and as directed. 88 s&f of 100mm size butt hinges, medium weight, cold rolled mild steel, and fixed, all as specified and directed. 89 s&f of 75mm size butt hinges, medium weight, cold rolled mild steel, and fixed, all as specified and directed. 90 s&f of 125 mm size aluminium handles, cast type, anodised, all as specified and directed. 91 s&f of 100mm size aluminium handles, cast type, anodised, all as specified and directed. 92 s&f of 200mm long aluminium anodised, barrel tower bolts of extruded section and fixed, all as specified and directed. 93 s&f of 125mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, all as specified and directed. 94 s&f of 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, all as specified and directed. 95 hacking out old broken glass, exc 1.5 sqm ( any thickness, quality or description ) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. 96 s&f of 3.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed. 97 s&f of 3.0mm thick sheet glass ground or obscured or frosted, on one side, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed. 98 s&f in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed. 99 s&f of bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks ( stay ) , heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to fe 290 gde e 165, complete all as specified and directed. 100 m&l for plain cement concrete ( 1:3:6 ) , type c1 ( using 20mm graded crushed stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. 101 s&f in repair of small fittings such as brackets of any type latch and hinge block, shaped door window stops and the like in second class hard wood article not exc 200 cucm each, complete all as specified and directed. 102 taking down eaves gutters and rainwater pipes ( any size or pattern ) , including all fittings, heads, shoes, bends, swan necks, etc., including cleaning or refixing or removal to store ( measured overall as fixed along the centre line over fittings and accessories ) , complete all as specified and directed. 103 s&f of 110mm bore pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. 104 s&f of 110mm bore pvc ( swr ) bends any radius, complete all as specified and directed. 105 rough excavation not exceeding 1.5 m deep and getting out in soft / loose soil, all as specified and directed. 106 returning filling in soft / loose soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm, complete all as specified and directed. 107 removal of surplus excavated soils to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point, complete all as specified and directed. 108 m&l for plain cement concrete ( 1:2:4 ) , type b 0 ( using 12.5 mm graded stone aggregates ) in coping, bed plates, parepet, plinth course including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. 109 demolition ofreinforced cement concrete ( reinforcement cut as required to facilitate demolition ) of any description and in any position not specifically provided for, complete all as specified andas directed. 110 use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete on square rectangular on plain or polygonal, complete all as specified and directed. 111 m&l for providing precast cement concrete ( 1:2:4 ) , type b 1 ( using 20mm graded stone aggregate ) as in landings, cover slabs ( for man holes, drain etc. ) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces with plain fair faces, including chamfers, weatherings, throating etc. and set in cement mortar ( 1:4 ) , complete with joints to match the surface, complete all as specified and directed. 112 m&l for mild steel tmt bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookingends and binding with mild steelwire ( annealed ) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. 113 m&l for mild steel tmt bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips, all as specified and as directed. 114 m&l for reinforced cement concrete ( nominal mix ) ( 1:2:4 ) , type b1 ( using 20 mm graded stone aggregate ) as in columns, pillars, piers, posts and struts, complete all as specified and directed. 115 s&f in repair of curtain rails / harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc., complete all as specified and directed. 116 taking down copper / aluminium point wiring ( light, fan, socket or power ) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed. 117 taking down carefully sub main wiring of any size / core / type including conduit / cashing / batten of any type and making good disturbed surfaces to match with the existing surface roof / wall / floor, complete all as specified and directed. 118 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for light / fan / bell on independent board, point controlled by one switch including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 119 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for light / fan on independent board, point controlled by two way switchs including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) three run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 120 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one 3 pin socket outlet 5 amps on the same board with other switches including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 121 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one 3 pin socket outlet, 5 amps on independent board, point controlled by one switch including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 122 m&l for point wiring with 2.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 25mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one 3 / 5 pin socket outlet, 5 / 15 amps on independent board, point controlled by one switch including 2.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( i ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 2.5 sq.mm for phase and neutral and one run of 2.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed ) 123 m&l for point wiring with 1.5 sq.mm ( nominal area ) pvc insulated sheathed single core multi stranded copper conductor frlsh cable 1100 volts grade ( conforming to is ) drawn through and includingrigidnonmetallic pvc conduit not less than 20mm dia ( concealed ) , medium grade with all necessary fittings, concealed wiring for one bell / buzzer point controlled by one push button on the same board with other switches or independent including 1.5 sq mm pvc frlsh insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.60 mm thick pressed steel terminal boxes including flush metal box 2 / 4 / 6 / 8 / 12 module with module inner and outer plates for mounting moduler switches, socket outlet, regulator etc. with 3 mm thick laminated bakelite sheet cover for housing switches, socket outlet, regulator etc., complete all as specified and directed including testing on completion.notes: ( a ) proper colour coding of pvc insulated copper wire should be maintained as red / yellow / blue wires for phases, black wire for neutral and green wire for earth. ( b ) two run of 1.5 sq.mm for phase and neutral and one run of 1.5 sq.mm for earth wire. ( c ) concealed type in permanent bldg and surface type in temporary bldg or as directed. 124 m&l for modular switch one way 6 amps, 1 module, 240 volts, all as specified and directed. 125 m&l for modular switch two way 6 amps, 1 module, 240 volts, all as specified and directed. 126 m&l for modular bell push 6 amps 1 module, 240 volts, all as specified and directed. 127 m&l for modular socket, 6 amps 2 / 3 pin combined 2 module, 240 volts, all as specified and directed. 128 m&l for modular socket, 6amps / 16amps 2 / 3 pin combined 2 module, 240 volts, all as specified and directed. 129 m&l for modular switch one way 16 amps, 1 module, 240 volts, all as specified and directed. 130 m&l for ceiling rose, 3 phase / pvc / polycarbonate, isolated body, three terminal, 240 volts, all as specified and directed. 131 m&l for modular blank plate, 1 module, 240 volts, all as specified and directed. 132 m&l for modular white cover plate with frame, 2 module, 240 volts, all as specified and directed. 133 m&l for modular white cover plate with frame, 3 module, 240 volts, all as specified and directed. 134 m&l for modular white cover plate with frame, 4 module, 240 volts, all as specified and directed. 135 m&l for modular white cover plate with frame, 6 module, 240 volts, all as specified and directed. 136 m&l for modular metal flush box, 1 / 2 module, 240 volts, all as specified and directed. 137 m&l for modular metal flush box, 3 module, 240 volts, all as specified and directed. 138 m&l for modular metal flush box, 4 module, 240 volts, all as specified and directed. 139 m&l for modular metal flush box, 6 module, 240 volts, all as specified and directed. 140 m&l for buzzer, ding dong ac. 230 volts, single pole, all as specified and directed. 141 supply and fixing in repair / replacement of led tube lights fitting 4feet, 1x 22w, 230v, decorative ultra slim extruded aluminium batten fixure with high lumen output, environmental friendly, all as specified and directed. 142 supply and fixing in repair / replacement of decorative box type fitting suitable for 4feet led tube light, 1x 22w, 230v, bipin holder, connector block, driver etc. with all accessories internally pre wired connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and pvc square blocks for fixing led fittings, all as specified and directed. 143 m&l in repair / replacement of lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. 144 supply and fixing in repair / replacement of building security light fittings new generation energy saving and enviornmental friendly long life versatile pressure die cast aluminium ip66 protection with acrylic cover of led 35 watts luminaire including gi bracket of suitable size with clamp, complete all as specified and directed. 145 s&f of sub main wiring with two single core 2.5 sqmm pvc ( frlsh ) copper conductor, insulated multistranded unsheathed cable medium grade including pvc conduit concealed of required size ( not less than 32mm ) conforming to is 2079 1973 with accessories for sub main connection including 2.5 sqmm pvc ( frlsh ) insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified and directed. ( note: three runs of 2.5 sqmm pvc frlsh copper conductor shall be measured as one unit length ) . 146 s&f of sub main wiring with two single core 4.0 sqmm pvc ( frlsh ) copper conductor, insulated multistrandedunsheathed cable medium grade including pvc conduit concealed of required size ( not less than 32mm ) with accessories for sub main connection including 4.0 sqmm frlshinsulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly, all as specified and directed. ( note : three runs of 4.0 sqmm pvc frlsh copper conductor shall be measured as one unit length ) . 147 s&f of sub main wiring with two single core 6.0 sqmm pvc ( frlsh ) copper conductor, insulated multistranded unsheathed cable medium grade including pvc conduit concealed of required size ( not less than 32mm ) with accessories for sub main connection including 6.0 sqmm pvc ( frlsh ) insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified and directed. ( note: three runs of 6.0 sqmm pvc frlsh copper conductor shall be measured as one unit length ) . 148 supply and fixing in repair / replacement of triple pole and neutral ( tpn ) db with sheet metal enclosure, 4 way, double door, 415 volt suitable for mounting incoming and outgoing mcbs, complete all as specified and directed. 149 supply and fixing in repair / replacement of sheet metal enclosure, double door for mcb dbs, 8 way single pole & neutral ( spn ) and current carrying capacity of 200 amps rated bus bar suitable for 240 volt, ac, 50hz, complete all all as specified and directed. 150 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of single pole ( sp ) and current carrying capacity of 5 to 32 amp duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, complete all all as specified and directed. 151 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of single pole & neutral ( spn ) and current carrying capacity of 32 amps duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, all as specified and directed. 152 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of single pole & neutral ( spn ) and current carrying capacity of 40 to 63 amp duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, all as specified and directed. 153 supply and fixing in repair / replacement of 240v, 10ka c curve miniature circuit breaker ( mcb ) of four pole ( fp ) and current carrying capacity of 63 amp duly fixed with lugs / sockets / thimbles etc. in the mcb db complete with connection testing and commissioning, all as specified and directed. 154 material and labour for earthing complete with galvanised steel earth plate electrode 60cm × 60cm× 6mm thick, buried directly in ground ( earth pit not less than 2.25 metres deep below ground level ) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised iron or steel earth lead wire 4.0mm dia size by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no. 3 ofmesssrpart i, connected to earthing test point all as specified or indicated including testing on completion, includingnecessary excavation and earth work in any type of soil, gi pipe 20mm dia light grade for watering and gi 15mm dia light grade pipe for protection of earth wire etc. upto test point, pcc chamber with pcc cover in cement concrete ( 1:2:4 ) type b 1 ( using 20mm graded stone aggregate ) , funnel, wire mesh, charcoal dust, salt etc, connected to db as indicated, complete all as specified and as directed.notes: contractor should conduct necessary test such as earth continuity, earth resistance test in presence of engineer in charge. 155 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, laying of underground cables etc. or for shafts, wells, cesspits, manholes, pier holes, under groung cables etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil, complete all as specified and directed. 156 m&l for sand filling under floors or in foundations or for protection of cable etc. including watering and consolidation, complete all as specified and directed. 157 supply and laying of old size burnt clay fly ash building bricks designation 75 ( kg / cm2 ) laid flat equal to width of bricks, perpendicular to under ground ( ug ) cable over the dry sand cushioning, for cable protection, complete all as specified and directed. 158 dismantling / taking out old unserviceable service connection cables / under groung cables, of any grade / type of size as below from pole / wall / cable duct / under ground trench etc, all as specified and directed. 159 supply and laying in trenches, fixed to wall / pole xlpe insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, 4.0 core, cross sectional area 16 sq.mm, complete all as specified and directed. 160 supply and laying in trenches, fixed to wall / pole xlpe insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, 4.0 core, cross sectional area 25 sq.mm, complete all as specified and directed. 161 m&l for 40mm dia steel tubes ( light grade ) galvanised with all fittings, laid in trenches / wall / pole / road crossing for protection of underground cable / earth strip, all as specified and directed. 162 m&l for cutting existing road / hard standing not exc 20x30 cm in wide and depth getting out excavated material for laying cable / gi tube, returning filling and well ramming wateringfinish suraface 10 cm from top using pcc 1:3:6; including removal of surplase soil, all as specified and directed. 163 note 1: ( applicable for all parts / items ) : the bidders / contractors are advised to read tender document, all drawings & all / amendments and general condition of contracts before entry / quoting the rates.note 2: the contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount....

Government Of West Bengal - West Bengal

39653132 tender for supply, installation, testing and commissioning of aluminium alloy milk cans with lids capacity 40 lit. (2000 nos.), data processor and milk collection unit (dpmcu) (660 nos.) and bulk milk coolers (bmc) (24 nos)...

South Eastern Railways - West Bengal

39590396 supply of installation and fixing, manufacturing, supply, installation and fixing made by supplier at jurisdiction of adra division of w / l & cee / faa ( in devnagari script ) marked whistle board, caution board, terminaiton board of sizes of irpwm. made out of 2mm thick aluminium alloy sheet conforming i.s.736 with back support of m.s.angle 25x25x3 mm. the entire face of the board shall be covered with yellow high intensity encapsulated retroreflective sheeting with hlva process. the letters shall be cut out of black high intensity encapsulated sheeting and provided on. the base sheet with hlva process. the board shall be fixed with m.s.angle of suitable size. [ warranty period: 30 months after the date of delivery ] => limited...

Indian Army - West Bengal

39563989 spare part of geg tess ord , steel 55c8 hex bar 6mm a / f tois:5517 78 part no nk , steel 25c8 r / bar dia 28mm tois:2004 1991 part no nk , steel 40cr4 r / bar dia 16mm tois:5517 93 part no nk , steel bar carbon h / r flat 40x4mm tois :2 part no nk , alluminium alloy plate 1715x1500x3mm part no nk , steel bar carbon h / r flat 30x12mm tois: part no nk , steel 40c8 wire 6mm tois: 1570 ( pt 2 / sec part no nk , steel 40cr4mo3 flat 65x40mm tois:5517 93 part no nk , steel bar round 42s dia 36mm tois: 226 7 part no nk , brazing flux silicofluse age silicon 650 part no nk , steel bar round dia 32mm bs:1501 pt.1 80 part no nk => limited...

South Eastern Railways - West Bengal

39525216 supply of speed indicator boards, manufacturing, supply, installation and fixing made by supplier at jurisdiction of adra division. speed indicator boards with the size of 1000mm equilateral trangle boards etc. made out of 02mm thick aluminium alloy sheet conforming to is 736 with back support of galvanized angle 25x25x3. the entire face of the board shall be covered with yellow high intensity encapsulated retro reflective sheeting with hlva process. the speed figure shall be cut out by black intensity encapsulated sheeting and provided on the base sheet with hlva process. the speed figure will be supplied by engineer in charge. [ warranty period: 30 months after the date of delivery ] => limited...

West Bengal Transport Infrastructure Development Corporation Limited - West Bengal

39382243 supply, fitting, fixing and installation of video conferencing setup along with all accessories, supply of laptops, eco sounder machine and total station machine for the office of the project office wbiwtlsdp , supply, fitting, fixing & installation of video conferencing setup along with all accessories, supply of laptops, eco sounder machine and total station machine for the office of the project office ( wbiwtlsdp ) including one ( 1 ) year manufactures warranty plus three ( 3 ) years of extended warranty i.e. four ( 4 ) years from end of commissioning period , supply & installation of laptop computer i5 10th generation intel® & core™ i5 10210u processor ( 6mb cache, up to 4.2 ghz ) , windows10 home single language english. amd radeon™ 610 series with 2g gddrs graphics memory 8gb, 8gxi, ddr4, 2666 mhz 256gb|m. 2 pcle nvme solid state drive+1 tb 7200 rpm 2.5 sata hard drive black colour cover for non touch lcd ( 2sp ) . web camera or its equivalent. ( brand: hp ) , supply, fitting, fixing & installation of scanjet pro enterprise sheet feed scanner. scan speed up to 24ppm / 48ipm, color scanning yes. scan technology cmos cis, scan type sheet fed. scan resolution hardware up to 600 dpi ( color and mono, sheet feed ) :optical: up to 600 dpi ( color and mono, sheet feed ) , scan size ( band hp scanjet pro enterprise 2000s ) . , conference hall : supply of led television set: supply, fitting & fixing of 5sinch led full hd recording system television set with mounting stand / frame for desktop / wall mounting with remote control along with battery. ( brand. sony ) white board: providing and fixing white writing magnetic board cum projection 05 screening with vitreous enameled steel sheet top surface, % gloss at 60 deg. lead 80 min; mounted on odium density fiber board ( mdf ) with electrogalvanized backing steel sheet and frame of anodized extruded aluminum alloys hollow section. the board shall have all around framing of anodized extruded aluminum alloy hollow section designation 63400 as per is 1285 2002. the frame section shall be 20 mm front: 16 mm side and wall thickness 12 mm. the writing board top surface shall be made up of steel sheet of thickness 0.3 to 0.4 mm and shall have vitreous enamel coating of 0.11 mm thickness on top and 0.03 mm minimum on the back. the top shall be free from waviness and shall show no scratches when hb to 3h pencils are used for writing. the surface shall show excellent irascibility when specified writing medium is used. it should be possible to fully erase the marking of permanent marker pens using methanol. the item also includes providing of a set of duster and two marker pens with every board. projector: supply, installation, testing, commissioning of projector of 2700 ansi lumens, xga / spg resolution, having warranty of 03 months or 500 hrs whichever is earlier for projector lamp, all complete as per direction of e.l.c. ( brand: panasonic / canon ) vc camera: yealink web camera of 20mp ( electric lens ) zoom facility with built up speaker uvc20 1080p hd video and audio conferencing system. hi gain screen: supply, installation, testing, commissioning of hi gain projector screen ( area 4 0 x 6 0 ) tripod economy / wall mounted economy screen, as per direction of e.i.c. speaker. providing fitting & fixing of special purpose p. a. wall speaker ( model no ps 400t ) at suitable position as per direction of e.i.c stabilizer: supply, delivery, installation, testing & commissioning of heavy duty 2 kva manual operated, auto cut voltage stabilizer. digital mixer & amplifier. 16 channel digital mixer: 16 inputs ( 4, xlritrs combo 12, xlr 2 stereo, 1 / 4 trs ) of qsc make & model touchmix 16 ups: ups. i kva online ups, voltage range 300 v 450 v, frequency range 50+ / 1.5 hz. phase single phase, voltage 220 vac / 230 vac / 240 vac selectable, battery type 12v. , supply of echo sounder machine as per specification to the satisfaction of the engineer in charge. product specification power: 300 w frequency range: 200 khz usage / application: port dredging – harbor survey chart mapping – rescue salvage brand:south body material: metal dimension w x h x d: 0.34 x 0.28 x 0.28 m packaging type: box voltage: 12 v weight: 6.7 kg accuracy: 98% country of origin: made in india , supplying of total station machine as per specification to the satisfaction of the engineer in – charge product specification brand hi –target angle measurement accuracy 2 second distance measurement 7500m usage / application land survey model name / number hts 420r 2” or similar magnification 30x keyboard full numeric keyboard display type dual sided lcd display and full numeric keyboard battery operation 10 hours reflectorless range 600 m...

Public Works Department - West Bengal

39382239 supply and placing of different furnitures for official use to the newly constructed administrative building for s.d.o. chanchal at chanchal under malda division, pwd, malda ( 2nd call ) . , sdos chamber , supply and placing of main table of size 1800 mm ( w ) x 900 mm ( d ) x 750 mm ( h ) . top surface of the table shall made up of mdf ( medium density fibre ) board duly finished with veneer and final coating of pu. the main desk should contain in built key board pull out tray for keeping keyboard of computer. the front modesty panel of the table shall be made up of mdf board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with veener and pu coating. for personal storage one mobile pedestal ( 3 drawer unit ) shall be provided of size 510 mm width x 635 mm height and 445 mm depth. the storage pedestal shall also be made up of mdf duly finished with veener & final coating of pu. the side shall be of size 1200mm width x 445mm depth x 660 mm height. the side unit shall be made up of mdf board duly finshed with veneer and final finish by pu coating. the design of the side unit shall be such that it can be placed on either side of the main table. the side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. the thickness of the top of the side unit shall be 25mm. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. , supply and placing of back unit matching with the main desk. the size of the back unit shall be 2215 mm ( w ) x 410 mm ( d ) x 2000 mm ( h ) . the back unit shall be made up of mdf board duly finished with veneer & final finish by pu coating. below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. the middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. the hardness of the pu coating shall be 1.5h. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. , supply and placing of executive high back chair. the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with pure leather and moulded high resilience ( hr ) polyurethane foam of density 45±2 kg / m3, and hardness load 16 ± 2 kgffor 25% compression.the cushioned back should bemade of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it should be upholstered with pure leather. the seat size should be : 47.6 cm. ( w ) x 49.2 cm. ( d ) and the back size should be: 47.5 cm. ( w ) x 77 cm. ( d ) . the armrest top should bemoulded from polyurethane ( pu ) , upholste. red in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk m.s e.r.w tube having chrome plated finish.the armrest height adjustable up to 6.5±0.5cm in 5 steps. the chair should be having active bio synchro mechanism: the adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • tilt tension adjustment can be operated in seating position. • 5 position tilt limiter giving option of variable tilt angle to the chair. • seat / back tilting ratio of 1: 2. • the mechanism housing should bemade up of hpdc aluminium black powder coated. the seat depth adjustment should beintegrated in the seat through a sliding mechanism. seat depth adjustment range should beof 6.0±0.5 cm. there should be 5 adjustable back support: back frame should beconnected to the up / dn mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment should have an adjustment stroke of 10.0±0.3 cm. the pedestal should behigh pressure die cast polished aluminium and fitted with 5 nos. twin wheel castors. the pedestal should be65.0 ± 0.5cm. pitch center dia. ( 75.0 ± 1.0cm. with castors. ) . the twin wheel castors should beinjection mouldedin black polypropylene. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. the bidder to submit oem certificate of product forgriha & svagriha, bifma level 2, green pro, greenguard, indoor advantage gold. , supply and placing of visitor chair. the seat assembly should bemade up of 1.2 ±0.1cm. thick hot pressed plywood, upholstered with fabric upholstery covers and moulded polyurethane foam. the seat size should be : 47.0 cm. ( w ) x 48.0 cm. ( d ) the back asembly. should bemade of powder coated ( oft 40 60 microns ) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. ms erw tube designed with contoured lumbar support for extra comfort. the back should beupholstered using double layer spacer mesh fabric with high tenacity yarn. the back size should be 46.5 cm. ( w ) x 60.5cm. ( h ) . the hr polyurethane foam should bemoulded with density =45+ / 2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. the one piece armrests should beinjection moulded from black co polymer polypropylene. the powder coated ( dft 40 60.microns ) tubular frame should becantilever type & made of ø2.54 ±0.03cm. x 0.2 ±0.016cm thick m.s.e.r.w. tube. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. bidder to submit oem certificate of product for indoor advantage gold, griha & svagriha, green pro. , supply and placing of 1 seater sofa with dimensions 870 mm x 820 mm x 790 mm. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. , supply and placing of centre table of dimension 904 mm ( w ) x 444 mm ( d ) x 411mm ( h ) . all panels are to be made of 18mm prelaminated particle board, with all exposed edges having 2mm thick pvc edge banding. the drawer is fitted with two way slides so that it can be opened from both sides. bottom & middle horizontal panel provides storage area. four nylon bushes are provided. the top should be 8mm thick toughened glass with uv plate glued on it. this glass is fixed with the side vertical panels. the construction should be knock down in nature. the finish should be of plt panels, uv guled plates under glass have sunray finish. the dowels for knockdown assembly with high quality standard hardware like screws, two way drawer slides and nylon bushes etc. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. , meeting hall ( big ) , supply and plaicng of table for for dias, worksurface should be made of 25mm khick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. plastic abs access flap is to provided for easy access to wires and cables. the understructure should consist of 18mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. aluminium alloy 63400 wp profile is used for connecting panels together. the product should be of knock down construction. the modesty panel should be made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. powder coated accent metal strip provided below work surface to enhance aesthetics. it should be made of 0.8mm crca as per is 513, epoxy polyester powder coated ( dft 40 60 microns ) . the wire management should be an array of panels made of 0.8mm crca ms is:513, epoxy polyester powder coated ( dft 40 60 microns ) is used for flow of wires and cables. provision to mount anchor roma 6 module plate is provided below worktop. cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio, video cables onto worktop and connect devices charger to power socket below worktop. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. bidder to submit oem certificate of products for griha & svagriha, green pro, greenguard, indoor advantage gold. , supply and placing of chairs. the seat and back should bemade up of injection moulded indoor grade polypropylene compound. the seat size should be 52.5 cm. ( w ) x 53.2 cm. ( d ) . the back size should be 51.6 cm. ( w ) x 40.5 cm. ( h ) . the powder coated ( dft 50±10 microns ) welded tubular frame should bemade from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm mserw tube. the shoes should bemade of indoor grade polypropylene compound and snap fitted with tubular frame. the armrest should bemade of indoor grade polypropylene compound and assembled over the tubular frame. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. bidder to submit oem certificate of products for green pro, greenguard, indoor advantage gold, griha & svagriha. , supply and placing of high back chair. the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area. the back size should be 47.5 cm. ( w ) x 69.5 cm ( h ) and the seat size should be 47.0 cm. ( w ) x 48.0 cm. ( d ) . the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. the one piece armrests should beinjection moulded from black co polymer polypropylene. the chair should have center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3. the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. the bellow should be3 piece telescopic type and injection moulded in black polypropylene. the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . the twin wheel castors should beinjection moulded in black nylon. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. bidder to submit oem certificate forproduct certificate of products for green pro, indoor advantage gold, griha & svagriha. , supply and placing of high back chair. the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should bedesigned with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area. the back size should be 47.5 cm. ( w ) x 58.0 cm ( h ) and the seat size should be 47.0 cm. ( w ) x 48.0 cm. ( d ) . the hr polyurethane foam should bemoulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. the one piece armrests should beinjection moulded from black co polymer polypropylene. the chair should have center tilt synchro mechanism: the mechanism should bedesigned with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment • seat / back tilting ratio of 1:3.the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. the bellow should be3 piece telescopic type and injection moulded in black polypropylene. the pedestal should beinjection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be66.3 ±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . the twin wheel castors should beinjection moulded in black nylon. bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. bidder to submit oem certificate of products for green pro, indoor advantage gold, griha & svagriha. , meeting hall ( small ) , supply and placing ofconference table. the worktop should be made of 25mm thick mdf. one side pre­laminate board conforming to is­14587:1998 with 0.4mm pvc membrane pressed on to top and having chamfered edge. access panels provided with soft closing hinges. the under structure should consists of mixture of 25mm and 18mm pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. anodised aluminium alloy 63400 wp profile is added at bottom edges for improving the aesthetics. the product should have a knock down construction. the bottom cabinet with door is provided for flow of wires and cables. cutout provision below access flap at four locations for standard 8 module anchor roma is provided. beside each cutout, an additional cutout with plate is provided for mounting audio visual cables ( eg. hdmi, vga a, etc ) . bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. bidder to submit oem certificate of products for griha & svagriha, green pro, greenguard, indoor advantage gold. , supply and placing of high back chair. the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric and moulded polyurethane foam with pvc lipping all around. the back foam should bedesigned with contoured lumbar support for extra comfort. the back size should be 49.0 cm. ( w ) x 71.0 cm. ( h ) and the seat size should be 49.0 cm. ( w ) x 44.0 cm. ( d ) . the hr polyurethane foam should bemoulded with density = 45 ±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. the armrest tops should beinjection moulded from black polypropylene. they should befitted to tubular armrest supports made of ø2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. m.s. e.r.w. tube and black powder coated ( dft 40 60 microns ) . the tubular armrest supports hold together the seat and back. the chair to have center tilt mechanism. the mechanism should bedesigned with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at center • upright position locking. • tilt tension adjustment. the pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. the twin wheel castors should beinjection moulded in black nylon. the bellow should be3 piece telescopic type and injection moulded in black polypropylene. the pedestal should befabricated from 0.2 ± 0.02 cm thick hr sheet , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0 ±1.0 cm. with castors ) . bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. , supply and placing of high back chair. the seat and back should bemade up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric and moulded polyurethane foam with pvc lipping all around. the back foam should bedesigned with contoured lumbar support for extra comfort. the back size should be ( w ) 49.0cm x ( h ) 71.0 cm, and the seat size should be 49.0 cm. ( w ) x 44.0 cm. ( d ) . the hr polyurethane foam should bemoulded with density = 45 ±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. the armrest tops should beinjection moulded from black polypropylene. they should befitted to tubular armrest supports made of ø2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. m.s. e.r.w. tube and black powder coated ( dft 40 60 microns ) . the tubular armrest supports hold together the seat and back. the chair to have center tilt mechanism. the mechanism should bedesigned with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at center • upright position locking. • tilt tension adjustment. the pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. the twin wheel castors should beinjection moulded in black nylon. the bellow should be3 piece telescopic type and injection moulded in black polypropylene. the pedestal should befabricated from 0.2 ± 0.02 cm thick hr sheet , powder coated ( dft 40 60 microns ) and fitted with an injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. the pedestal should be60.0 ±0.5cm. pitch centre dia. ( 70.0 ±1.0 cm. with castors ) . bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture. , supply and placing of visitor chair. the seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric and moulded polyurethane foam with pvc lipping all around. the back foam should bedesigned with contoured lumbar support for extra comfort. the back size should be 49.0 cm. ( w ) x 47.0 cm. ( h ) and the seat size should be 49.0 cm. ( w ) x 44.0 cm. ( d ) . the hr polyurethane foam should bemoulded with density = 45 ±2 kg / m3 and hardness load 16 ± 2 kgffor 25% compression. the armrest tops should beinjection moulded from black polypropylene. they should befitted to tubular armrest supports made of ø2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. m.s. e.r.w. tube and black powder coated ( dft 40 60 microns ) . the tubular armrest supports hold together the seat and back. the tubular frame should becantilever type & made of ø2.54 ±0.03cm. x 0.2 ±0.016cm.thk. m.s. e.r.w. tube and black powder coated ( dft 40 60 microns ) . bidder should submit oem certificate for igbc, iso 9001:2015, iso 14001:2015, iso 45001:2018, iso 50001:2018, iso 13485:2016 / ns en iso 13485:2016 from nabcb ( central govt ) accredited organization. certificates obtained from any other non approved agency will not be acceptable. bidder should submit certificate from all india occupational therapists’ association ( aiota ) confirming the design meeting the ergonomic standards and performance evaluation criteria for the office furniture range and the education furniture....

Department of Defence Production - West Bengal

39365160 bids are invited for aluminium alloy tube to is 738 desgn 24345 w or 64430 wp condition id 108mm od 90mm length 480mm (q3) , aluminium alloy tube to is 738 24345 or 64430 or 63400 wpt6 condn, od 100mm id 88mm length 230mm (q3) total quantity : 81...

Department of Defence Production - West Bengal

39275943 bids are invited for aluminium alloy tube to is 738 desgn 24345 w or 64430 wp condition id 108mm od 90mm length 480mm (q3) , aluminium alloy tube to is 738 24345 or 64430 or 63400 wpt6 condn, od 100mm id 88mm length 230mm (q3) total quantity : 325...

Northeast Frontier Railway - West Bengal

39273733 supply of gravity cock as per drg.no. icf drawing no: icf / sk 6 3 369, alt f / 2 item 1, specn: material specification : aluminium alloy. [ warranty period: 30 months after the date of delivery ] => limited...

Department Of Atomic Energy - West Bengal

39173334 bids are invited for aluminium alloy straight filler rod for tig welding, grade s ai 400 or 4043, diameter 2.4 mm (q3) , aluminium alloy straight filler rod for tig welding, grade s ai 400 or 4043, diameter 3.2 mm (q3) , aluminium alloy straight filler rod for tig welding, grade s ai 55000 or 5356, diameter 2.4 mm (q3) , aluminium alloy straight filler rod for tig welding, grade 4047, diameter 2.4 mm (q3) total quantity : 30...

Indian Army - West Bengal

39147681 tender for spare part for geg ssl eng; 1 alluminium alloy gde 64430 r / bar dia 80 part no nk 2 steel plate carbon h / r 2200 x 900 x 8 mm part no nk => limited...

Metro Railway - West Bengal

39113539 supply of aluminium / alloy trolly ladder platform height 8 ft. overall height 10 ft. with 1. load carring capacity 200 kg, 2. chain & lock for locking arrangement. 3. rubber wheel with break to immobilize when in use as per drawing no. al 7600a enclosed. 4. specification of alloy 6061 is spec:bs en 573 3:2009. [ warranty period: 30 months after the date of delivery ] ...

South Eastern Railways - West Bengal

39104633 supply of aluminium electrodes 3.15mm dia. tensile strength 24kg / sq.mm ( 34000 psi ) ; irs: class l ( for welding of mmaw, aluminium and aluminium alloys ) . material & specification irs m: 28 2020, is / aws spec. a5.3, is / aws code: al 43 ( medium coated ) . shelf life of this item is 12 months. [ warranty period: 12 months after the date of delivery ] workshop carriage stores / kgp , west bengal 50.00 kg...

Indian Army - West Bengal

39046973 tender for spare part for geg ssl eng , alluminium alloy gde 64430 r / bar dia 80 part no nk , steel plate carbon h / r 2200 x 900 x 8 mm part no nk => limited...

Uttar Banga Krishi Viswavidyalaya - West Bengal

39046478 tender for supplying camera accessories 01 compact super zoom tele lens focal length range 100 400 mm (35 mm format) or higher aperture range 5.6 8 or lesser angle of view (diagonal) 24°00′ 6°10′ closest focusing distance (m, ft.) 1.2 / 3.94 (at 100mm) or less 0.88 / 2.89 (at 200mm) or less 1.05 / 3.44 (at 400mm) or less diameter x length 79.5 × 164.7mm or smaller filter size 67 mm or larger no of diaphragm blades 9 or more minimum aperture 32 or more weight 650 g or less accessories must supply lens cap, lens hood and lens pouch preferred make canon/nikon/sony or equivalent 01 02 tripod material of construction aluminium or carbon fiber head interchangeable ball head or gimble head load bearing capacity 6 kg or higher weight of the item 2.5 kg or lighter special feature 1. central column can be reversed 2. all the legs must be spread to make the camera height not more than 1 ft. from the ground. supplied accessories tripod bag preferred brand vangurd/benro/ sirui 01 03 3 axis gimble for videographer  lightweight and compact, superior image stabilization,  3 axis gimbal stabilizer for mirror less cameras, nikon, sony, panasonic, canon or compatible  360 degree movement  2kg tested payload or higher  axis locks  preferred colour black  mounting hardware: gimbal x 1, bg18 grip (built in battery) x 1, 01extended grip/tripod (plastic) x 1, quick release plate x 1, camera riser x 1, carrying case x 1, phone holder x 1, lens support x 1, 8 pin port cover x 2, wrench x 2, camera screw 1/4 20 x 3, screw m4 x 4, multi camera control cable (multi usb) x 1, multi camera control cable (type c) x 1, usb c cable x 1, multi camera control adapter (type c tomicro usb) x 1  voltage : 7.2 v or higher  wattage: 17.64 watts or higher  battery cell composition: nmi mui til  construction material: metal  battery average life: 10 hrs. or more  weight: 1.2 kg or less  preferred make: dji or moza or any reputed international brand 04 80 litres cnc humidity control dry cabinet  capacity: 80 litres, moisture control range: 25% 60% rh, moisture control: microcomputer digital control adjustment, display mode: led lcd dual display (temperature and humidity)  laminate: abs plastic black, drawer type, height position can be adjusted, quantity 2pc, door material: aluminum alloy door + 4 mm toughened glass  adapter: input ac 110 220v output: dc 5v 2a, power consumption: 5 w/h  item dimensions l x w x h: 39 x 38 x 41.6 centimetres  storage volume : 80 l or higher  weight : 13 kg or less  internal lighting  adjustable self  magnetic seal for the door  locking facility for the door and must have handle  multi voltage power supply  adjustable legs or foot  preferred make : andbon or sirui or any internationally reputed brand ...

Indian Army - West Bengal

38989197 bids are invited for portable nitrogen purging machnie general purpose with all accessories model nfpv estp gp emvp comprises of , nitrogen purging controller with vaccum pump model gp emvp , 2.2 ltr wc 330 ltr gas capacitylt wt hp aluminium alloy seamless design nitrogen cylinder model ace 330 peso certified 2yrs mfg and 5 yrs tested warranty , nitrogen purging nozzel set contains 7 nozzels , customized ms care with back pack , cylinder pressure control regular ss with 2 indicating gauge and outlet flow control total quantity : 6...

Indian Army - West Bengal

38939143 bids are invited for nk 1 portable nitrogen purging machnie general purpose with all accessories . model nfpv estp (gp emvp) comprises of 2 nk 2 nitrogen purging controller with vaccum pumpmodel gp emvp 3 nk 3 2.2 ltr wc 330 ltr gas capacitylt wt hp aluminium alloy seamless design nitrogen cylinder model ace 330 (peso certified 2yrs mfg & 5 yrs tested warranty) 4 nk 4 nitrogen purging nozzel set (contains 7 nozzels) 5 nk 5 customized ms care with back pack 6 nk 6 cylinder pressure control regular ss with 2 indicating gauge and outlet flow control ...

Department of Defence Production - West Bengal

38937264 bids are invited for al alloy netlock neta grip dqan 14640 for svl 1 al alloy netlock ( neta grip ) _dqan / 14640 ( aluminium alloy netlock ( neta grip ) to suit 10 mm dia nylon rope as per dqan drawing no. dqan / 14640 ( latest issue. each net lock will consists of one male and one female netlock .material aluminium alloy to bs 1470 ns 3 in o condition ) 2 mtc, gc and wc 3 al alloy netlock ( neta grip ) _dqan / 14640 ( aluminium alloy netlock ( neta grip ) to suit 10 mm dia nylon rope as per dqan drawing no. dqan / 14640 ( latest issue. each net lock will consists of one male and one female netlock .material aluminium alloy to bs 1470 ns 3 in o condition ) 4 mtc, gc and wc 5 al alloy netlock ( neta grip ) _dqan / 14640 ( aluminium alloy netlock ( neta grip ) to suit 10 mm dia nylon rope as per dqan drawing no. dqan / 14640 ( latest issue. each net lock will consists of one male and one female netlock .material aluminium alloy to bs 1470 ns 3 in o condition ) 6 mtc, gc and wc 7 al alloy netlock ( neta grip ) _dqan / 14640 ( aluminium alloy netlock ( neta grip ) to suit 10 mm dia nylon rope as per dqan drawing no. dqan / 14640 ( latest issue. each net lock will consists of one male and one female netlock .material aluminium alloy to bs 1470 ns 3 in o condition ) 8 mtc, gc and wc total quantity : 14812...

West Bengal Electronics Industry Development Corporation Limited - West Bengal

38912364 tender for civil maintenance works at stp ii 1 m.s. structural works in columns, beams etc. with simple rolled structural members ( e.g. joists, angle, channel sections conforming to is: 226, is: 808 & sp ( 6 ) 1964 connected to one another with bracket, gussets, cleats as per design, direction of engineer in charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to is: 816 1969 & is: 1995 using electrodes of approved make and brand conforming to is:814 2004, haulage, hoisting and erection all complete. the rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges and two coats of red lead primer with approved brand ( asian paints / dulux / berger ) etc. payment to be made on the basis of calculated weight of structural members only in finished work as per is specified weight. payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of engineer in charge. at all floor level. 2 for structural members of specified sections weighing less than 22.5 kg. / m 3 ii ) for structural works in roof trusses etc. using joists, channels and angles of specified section weighing less than 22.5 kg / m 4 taking out and refixing ss plates from column facia with new screws to the ms structural framework , adjusting, welding, cleaning, cutting holes, mending good damage to match with the existing one complete with all screws, welding etc. 5 hire and labour charges for high scaffolding all round ( outside ) for repairing of column facia 6 labour for taking out lowering and stacking after dismantling in parts r.s. joists, channels, angles, tees, plates, ladders etc.complete as directed. 7 from 1st floor level 8 extra for each addl. floor 9 supply, fitting & fixing upvc pipes a type and fittings conforming to is:13592 1992 with all necessary clamps / nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails ( spun yarn, valamoid / bitumen / m seal etc ) and taking out of old ci pipes complete. dia 160 mm 10 stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 11 removal of rubbish, earth etc. from the working site and disposal of the same beyond the compound, in conformity with the municipal / corporation rules for such disposal, loading into truck and cleaning the site in all respect as per direction of engineer in charge 12 plaster ( to wall, floor, ceiling etc. ) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding / staging where necessary ( all floor ) 13 with 1:4 cement mortar, 15 mm thick plaster 14 with 1:4 cement mortar, 20 mm thick plaster 15 removing old scales, blisters etc. of interior surface of walls, ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar ( 1:2 ) ( as necessary ) , to make the surface suitable for receiving putty / primer. ( payment against this item will be made only when this has been done on the specific direction of the engineer in charge ) , all floors ( make: dulux / asian paints ) 16 rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand ( 1.5mm thick ) 17 applying interior grade acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive distemper / acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the eic. ( all floors ) one coat, water based interior grade acrylic primer 18 applying acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty ( to be done under specific instruction of superintending engineer ) : ( two coats ) , standard quality 19 supply, fitting and fixing boiling water resistant ply conforming to is: 303 1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design ( for drawers and tables ) and as per approval and direction of engineer in charge. all floor ( century / greenply ) , 16mm 20 supply, fitting, fixing decorative lamination conforming to is: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on particle / mdf / ply boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of engineer incharge. the rate includes the cost of labour, adhesive and all incidental charges thereof. all floor glossy / matt / suede excluding surface texture or metallic lustre. thickness of laminate 1.5mm ( century / greenply ) 21 supplying, fitting and fixing godrej multi lock or equivallent for drawer 22 taking out existing partition / ceiling of particle board, masonite board, ply board, soft board, laminate etc. of any thickness and mending damages if any. 23 labour for taking out rolling shutter ( only shutter portion ) dismantling by parts for repair or ( replacement of damaged parts only ) , rehanging and refitting the same in position after necessary repairs ( excluding the cost of supply of new parts ) . 24 renewing seam pipe for rolling shutter as per existing size and shape fitting, fixing complete. 25 renewing side split pin for seam pipe for rolling shutter. 26 oiling and greasing of rolling shutter and repair to in side lock. 27 renewing spring of rolling shutter as per existing size and shape including fitting fixing complete. 28 easing and oiling, cleaning rolling shutters including repair to inside locks. 29 1st class brickwork of width 200 mm. with non modular bricks in cement and sand mortar ( 1:4 ) 30 ( a ) in foundation and plinth 31 ( b ) in superstructure ground floor 32 asbestos corrugated ( trafford or similar approved quality ) sheet ( 6 mm thick ) work ( excluding the supporting framework ) fitted and fixed with 9.5mm. dia. j or l hook bolt and nuts, limpet and bitumen washers and putty with 150 mm end lap & one corrugation minimum side lap complete. ( payment should be made on area of finished work ) , in roof 33 dismantling r.c. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. in ground floor including roof. 34 dismantling carefully wooden walling, flooring or false ceiling and stacking dismantled materials as directed. 35 providing and fixing of false ceiling with powder coated exposed g.i. grid suspension system ( e grid t 2430 / 1510 or equivalent load carrying capacity with mid span deflection not exceeding 1 / 360 span with hanger spacing of 1200mm c / c ) consisting of main runner 3600 mm long, cross tee 1200 mm / 600 mm long and wall angle. the wall angle shall be fixed on pvc dash fasteners on the perimeter of the wall by steel screws with distance 300mm c / c. the main runners to be placed @ 1200 mm. the cross tee 1200mm will be inserted in the pre cut slots of main runner at regular interval of 600 mm to form a modular grid of 1200mm x 600mm. additional cross tees of 600 mm shall be placed perpendicular to the cross tee 1200 mm long to finally form a grid of 600 mm x 600 mm. grid of module size 600 mm x 600 mm shall be supported by 6 mm dia g.i. wire from purlins / soffit. 4 mm thick high pressure steam cured non asbestos fibre cement standard ceiling board ( density > 1300 kg / m3 ) of size 595 mm x 595 mm, conforming is 14862 & type b category iii of iso 8336, tested as per as 1530 part 3 & bs 476 part 4, 5, 6, 7 & 8, should be placed in the grid module to form a false ceiling. all complete as per the drawing & directions of engineer in charge. in ground floor false ceiling ( with 4mm thick fibre cement standard ceiling board and egrid t 2430 / 1510 ) . 36 supplying & laying of approved brand of scratch proof, semi flexible p.v.c. blended homogeneous marble vinyle flooring in tiles conforming to is:3461, fixing with synthetic acrylic adhesive after preparing the floor, levelling & smothaning when necessary with suitable putty, as per the design & instruction of the engineer in charge. 2 mm thick 37 supply, fitting and fixing chekered plate of thickness 5 mm, fitted in m.s. angle ( 25 x25 x5 mm ) frame and two handles made of 12 mm m.s. round bars for pit covers etc as per drawing & direction of eic.. all welding spots should be properly filed or rounded smooth including cost of welding rods, two coats of red oxide paint and two coats of synthetic emulsion paint, labour complete with all other incidental costs. 38 ordinary cement concrete ( mix 1:2:4 ) with graded stone chips ( 20 mm nominal size ) excluding shuttering and reinforcement, if any, in all floors as per relevant is codes pakur variety 39 ordinary cement concrete ( mix 1:2:4 ) with graded stone chips ( 20 mm nominal size ) excluding shuttering and reinforcement, if any, in all floors as per relevant is codes ( in thin sections only upto thickness 65 mm ) pakur variety 40 hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works ( all floors ) 25 mm to 30 mm thick wooden shuttering as per decision & direction of engineer in charge. 41 reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust ( if necessary ) , cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. all floors, other than sail / tata / rinl 42 labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. ( concrete and brick work for mending damage will be paid separately ) above area 2.5 sq.m 43 hydraulic door closer of approved quality as per i.s.i. standard fitted and fixed complete. heavy type ( i.s.i. size 3 ) 44 supplying heavy duty hydraulic double action floor spring along with top pin / set of pivots conforming to is: 6315 or any approved make as per direction of engineer in charge. 45 supplying heavy duty top pin / set of pivots of local make and approved by the engineer in charge. ( this item to be provided where floor spring not used ) . 46 supplying zinc powered coated star lock 47 supplying, fitting and fixing aluminium door lock 48 supplying pvc rollers for sliding windows as per direction of engineer in charge. 49 labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units: glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or epdm gasketing in between window frame and masonry work ( walls, column, beam.lintels etc. ) as well as between glass and shutter frame for fixing glass and polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of eic. the rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / epdm gasket, locking arrangement and rollers. fixed glazing. 50 supplying bubble free float glass of approved make and brand conforming to is: 2835 1987. 4mm thick clear glass. 51 supplying profiles of required section made of aluminium alloy extrusions conforming to is: 732 1983 and is: 1285 1975; annodized ( with required film thickness and specified colour / natural ) matt finished conforming to is: 1868 1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any isi embossed / certified make and brand as per direction of engineer in charge. ( payment will be made on finished length of the work ) . in 10 12 micron thickness annodizing film, natural white, fixed glazing. 52 top, bottom and side member. 53 mullion. 54 glazing clip. 55 suuply, fitting & fixing single skin, colour coated trapezoidal profile for wall cladding, roof shall be made of 0.45 mm bmt ( base metal thickness ) , 0.5 mm tct ( total coated thickness excluding paint, g550 ( min 550 yield strength ) , of zincalume metallic coating ( is 15965 ) with high solar reflectance index ( sri ) value for better coiling as per thermatech technology, 1000 1500 mm effective cover width with five major corrugation, 28 mm high rib spaced at 203 mm c / c with subtle square flunting in the pan and the end rib shall have anti capillary groove and return leg. the sheet shall be fastened with 40 micron zinc coated or 25 micron zinc tin alloy coated, hex head, self drilling screw as per is 3566 2002 class 3 fastener. the base steel shall be coated with zinc aluminium alloy zincalume ( az 150 ) , i.e, 55% al, 43.4% zinc, 1.6% si, minimum of 150g / sq cm coating total on both sides, pre painted with colorbond xrw ( exterior roofing, walling ) paint system of 35 micron super durable polyester paint ( sdp ) with stable inorganic pigment with no lead contents conforming is15965. the sheet shall be free from defects and have brand marking of the manufacturer giving product details on the back of the sheets at regular interval confirming genuity of the material complete with 150 mm end lap and one corrugation minimum side lap. ( payment to be made on area of finished work, laps not payable ) . brand: tata, colour: blue, all floors 56 painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary on steel or other metal surface : with other than hi gloss of approved quality two coats ( with any shade except white ) 57 painting with ready mixed red lead paint of approved make and brand including scraping of old layer of paint and rust : one coat 58 m.s. door as per approved design made of strong m.s. frame work, intermediate stiffeners and round / square bars or angles. m.s. sheet ( not less than 14 gauge ) gussets, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the engineer in charge. at all floors 59 supplying fitting and fixing door frame with m.s. angle ( 50 mm x 50 mm x 8 mm ) as per drawing & direction of required section.the holes for counter sunk machine screw & nuts will be such as to fit 8 to 10 mm iron screw. the counter sunk nut to be welded . the nuts are to be welded after careful checking with screw.all welding spots should be properly filed or rounded smooth including cost of welding hinges for hinge cleats , lugs for hasp bolt, socket bolt etc. and necessary m.s. clamps of 25mm x 6mm flat 225mm long as per direction welded to the frame fitted and fixed in position excluding cost of concrete 60 supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. ( for water lines only ) . 61 100 mm dia 62 50 mm dia 63 32 mm dia 64 25 mm dia...

Military Engineer Services - West Bengal

38897301 tender for comprehensive maintenance of misc structural repair, dampness, leakage, seepage, roof treatment, ceiling, columns, chajja, fins, facia, rainwater pipes, flooring, plastering, plinth protection, plumbing, doors, windows, ventilators, grills, guard bars, fly proofing, joinery, 1 taking down / dismantling loose / damage concrete including plaster of any description and in any position from rcc structures like chajja, fins, roof ceiling, louvers, parapet, column, beam, and of lintel by hammering with wooden mallets carefully chipping off the old concrete surface with necessary scaffolding upto 24mtr height including cutting of rusted reinforcement if so required and disposal of old debris to outside the premises including cleaning the existing surface of concrete and reinforcements as obtained after dismantling by wire brush including scrapping & cleaning with emery paper or by air blasting or sand blasting incl foreign matrials , loose concrete / aggregate etc andwashing down with water as required complete all as specified and directed. 2 material andlabour for tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending lapping etc as required and welding with existing bar complete all as specified and as directed. 3 material and labour for tmt bars 6 to 8mm bar, cut to length, bent to shape required, including cranking, bending, lapping etc as required and welding with existing bar complete all as specified and as directed. 4 material and labour for tmt deformed bar or twisted bars upto 10mm dia as in stirrups cut to lenth bent to shape required including cranking , bending etc and lapping , welding as directed to the existing one complete all as specified and as directed. 5 m & l for providing single coat of epoxy bond adhesive of prepared non metallic surface ( existing surface ) and applying by brush all as per manufactures instruction / specification. the bonding agent shall have minimum compressive strength of 40 n / sqmm and complete all as specified and directed. 6 supply and application of epoxy zinc rich primer on the steel surface by brush the primer shall have a minimium specific gravity 1.75 minimum weight film thickness / coat 40 microns and minimum adhesive bond strength with steel is 1.5n / mm2 including cleaning and removing loose concrete from steel surface complete all as specified and directed. 7 m&l for providing and placing in position free flow non shrink cementitious micro concrete of grade of m 30 to the effected beam, column etc . the micro concrete shall have a minimium 1 day compressive strength of 10 mpa and 28 days strength of 30 mpa, minium tensile strength 5n / mm2 @ 28 days, minimium flextural strength 5n / mm2 @ 28days and complete all as specified and directed. 8 supply, mixing and application two component structural grade polymer modified reinstatement mortar, where local spalling has taken place or shuttering is not possible . the mortar can be applied in layers not exceeding 6mm thick in each layer in and upto any thickness in smaller vertical pockets and upto any thickness in horizontal applications. the mortar should have a minimium compressive strength 12n / mm2 in 1 day and 45n / mm2 in 28 days. minimum flexural strength should be 8 n / mm2 in 28 days. a modified styrene butadience emulsion for use as a bonding aid and gauging liquid for cementious system to be mixed with cement slurry before the application of modified polymer mortar to be used @ 6 ltr / bag of cement. the bonding agent should have minimium compressive strength 24n / mm2. minimum tensile strength 3.5n / mm2, minimium flexural strength 6.5n / mm2 upto 25 mm average thickness complete all as specified and directed. 9 use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished concrete surfaces complete all as specified and as directed. 10 use and waste of formwork to sides of sides and soffits of beams, lintels, floors etc. for rough finished concrete surfaces complete all as specified and as directed. 11 use and waste of formwork to parapet, rcc wardrobe and similar items for rough finished concrete surfaces complete all as specified and as directed. 12 use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works n.exc. 200mm thick etc for rough finished concrete surfaces complete all as specified and as directed. 13 use and waste of formwork tofins, facia, louvers. parapet, chajja etc for rough finished concrete surfaces complete all as specified and as directed. 14 material and labour for 5 mm thick plastering in cm ( 1:3 ) on concrete surfaces as in sides of column, lintel, beam, chajja, facia, railing, rcc wardrobe etc including finish the surface even and fair without using extra cement complete all as specified and as directed. 15 material and labour for rcc 1:1.5:3 type a1 ( using 20mm graded stone aggregate ) as in fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and as directed. 16 m&l for reinforced cement concrete m 25 ( design mix ) in chajjas and like complete all as specified and directed. 17 taking up or down 15mm dia steel tubing and connections, segregating serviceable pipe for reuse complete all as specified and as directed. 18 all as per item no. 17 above but 20mm dia complete all as specified and directed. 19 all as per item no. 17 above but 25mm dia complete all as specified and directed. 20 supply and fix 15mm bore unplasticised pvc pipes of pressure rating 10 kgf / cm sq fixed to walls , ceiling or in floors etc complete all as specified and directed. 21 all as per item no 20 above but 20 mm outer dia complete all as specified and directed. 22 all as per item no. 20 above but 25mm dia complete all as specified and directed. 23 supply and fix 15mm bore medium grade galvanized steel tubes with all fittings and fixed to wall or in floors etc complete all as specified and as directed. 24 all as per item no. 23 above but 20mm dia complete all as specified and directed. 25 all as per item no. 23 above but 25mm dia complete all as specified and directed. 26 taking down chowkahts or frames with shutters ( without taking off shutters from the frame ) not exceeding 1.5 sqm each complete all as specified and as directed. 27 taking down chowkahts or frames with shutters ( without taking off shutters from the frame ) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and as directed. 28 taking down shutters of any description exceeding 1 sqmbut not exceeding 2 sqm each complete all as specified and as directed. 29 refixing of shutters in same opening of any descriptionexceeding 1 sqm each with old serviceable builders hard ware articles / with new builders hard warearticles if any complete all as specified and as directed. 30 taking down old unservicebale steel window / ventilators frame with shutter of any description. 31 supply and fix 2nd class hard wood , plain, solid , straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed. 32 materials and labour for treating back of chowkhats etc with tar or coal tar black paint, area tarred exceeding 0.10 sqm but not exceeding 0.50 sqm each complete all as specified and as directed. 33 supply and fix 35mm thick 2nd class hard wood factory made plain framed panelled door shutters, ( two panel ) with lock rail and panel of 12mm veneered particle board with commercial veneered on both faces and rail and stiles as per is 1003 ( pt i ) , kilnseasoned and chemically pressure treated etc. complete all as specified and as directed. 34 supply and fix 35mm thick 2nd class hard woodfactory made glazed and skeleton door shutters, open rebated and prepared to received glass / gauge etc ( without sash bars ) edges of framing plain, chamfered or rounded and mitred , beads for securing glass etc the size of member of shutter as specified in ssr part i, clause 8.24 ( a ) complete all as specified and as directed. 35 supply and fix 30mm thick flush shutters solid core construction with particle board core and plywood face panels, one face covered with decorative face veneer with lipping / frame to match complete all as specified and as directed. 36 supply and fix factory made solid pvc mouldeddoor shutter 28 to 30 mm thick ( stiles ) with 2, 4 or 6 raised panel design with 2mm thick moulded pvc sheet on back face , with particle board core , supplying and fixing in frame at site as per specification and drawing complete all as specified and directed. 37 supply and fix solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube with epdm gasket as per specification and drawing complete all as specified and as directed. 38 supply and fix factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, as per specification and drawing complete all as specified and as directed. 39 supply and fix in repairs prelaminated particle board18 / 19 mm thick, interior grade one side decorative choice lamination and other sidebalancing white lamination fixedin cup boards shutters with 6mm thick teak wood lipping / edging all round complete all as specified and as directed. 40 supply and fix in repairs prelaminated particle board18 / 19 mm thick, interior grade one side decorative choice lamination & other sidebalancing white lamination fixedin cup boards shelves with front side 6mm thick teak wood lipping / edgingcomplete all as specified and as directed. 41 material and labour for pcc ( 1:3:6 ) type c1 ( using 20mm graded stone aggregate ) for fixing of hold fasts block and similar work including necessary form work complete all as specified and as directed. 42 supply and fix mild steel work as in hold fast or similar article conforming to fe 410 0 or fe 310 0 including tarring and sanding complete all as specified and as directed. 43 supply and fix 100 mm size stainless steel butt hinges, medium weight fixed with cadmium plated screws complete all as specified and as directed. 44 supply and fix 100 mm size butt hinges, medium weight, cold rolled mild steel ( isi marked ) complete all as specified and as directed. 45 supply and fix300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. 46 supply and fix 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed. 47 supply and fix 150mm size extruded aluminum alloy handle fabricated type anodized ( isi marked ) complete all as specified and as directed. 48 supply and fix steel windows with side hung double shutters ( both glazed and gauged shutters ) in single frame including box type hinges with steel handle, and steel peg stay, complete with glazing bars for glazed shutter, dovetailed or welded including taking down old rusted unserviceable steel windowwith glass panes / wire mesh / grill / guard bar and all fittings complete all as specified and as directed. 49 supply and fix steel windows with side hungshuttersincluding box type hinges with steel handle and steel peg stay complete with glazing bars, flush butt welded etcincluding taking down old windows with glass panes, grill / guard bar etc and all fittings complete all as specified and as directed. 50 supply and fix 3mm thick sheet glass, ordinary quality and glazing with oil putty / wooden beadings in square n exc 0.5 sq. m in each pane fixed to wooden frame complete all as specified and as directed. 51 supply and fix 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane fixed to steel frame complete all as specified and as directed. 52 supply and fix 3mm thick frosted glass ordinary quality, glazing with oil putty in square not exceeding 0.5 sqm in each pane fixed to wooden frame with wooden beading complete all as specified and as directed. 53 supply and fix 3mm thick frosted glass ordinary quality, glazing with oil putty in square not exceeding 0.5 sqm in each pane fixed to steel frame complete all as specified and as directed. 54 supply and fix rolled mild steel fe 410 w ( grade e 250 ) quality a framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars and similar work complete all as specified and as directed. 55 supply and fix 3mm thick sheet glass, ordinary quality and glazing each pane fixed to steel frame ( fixed with oil putty and clips ) / wooden frame ( fixed with iind cl hard wood beads ) including hacking out old broken glass from metal frmae / wooden frame complete all as specified and as directed. 56 supply and fix 3mm thick frosted glass, ordinary quality and glazingin each pane fixed to steel frame ( fixed with oil putty and clips ) / wooden frame ( fixed with iind cl hard wood beads ) including hacking out old broken glass from metal frmae / wooden frame complete all as specified and as directed. 57 supply and fix stainless steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples complete all as specified and as directed. 58 supply and fix in repairs stainless steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples complete all as specified and as directed. 59 material and labour for two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer to new steel surface including preparation of surfaces exceeding 10cm with or girth complete all as specified and as directed. 60 material and labour for two coats of synthetic enamel paint over a coat of pink primer to new wooden surfaces of any description over 10cm width or girth including preparation of new surfaces complete all as specified and as directed.. 61 supply and fix aluminium powder coated glazed or gauged shutter for sliding window ( 2 or 3 track ) with aluminium channel section weighing not less than 0.55 kg per sqm including aluminium channel, including all necessary fittings such as rollar, joining cleats, glazing clips, rubber packing aluminium screw as required etc complete all as specified and as directed. ( note:wiremess / glass shall be measured and paid separately ) 62 supply and fixpowder coated aluminium framefor doors, windows, ventilators ( including 2 / 3 track ) with one or more rebates including joining cleat for fixing etccomplete all as specified and directed. 63 supply and fix aluminium powder coated door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. 64 supply and fix 4mm thick sheet glass ordinary quality, glazing with aluminium beads in square / rectangularexceeding 0.5 sqm in each pane fixed to aluminium frame complete all as specified and as directed. 65 supply and fix 5.50mm thick sheet glass ordinary quality, glazing with aluminium beads in square / rectangularexceeding 0.5 sqm in each pane fixed to aluminium frame including, rubber packing aluminium screw as requiredcomplete all as specified and as directed. 66 supply and fixin repair 25mm dia powder coated aluminium curtain rod fancy type ( length from 0.90m to 1.5m ) with fancy type end side brackets and fancy type hanging brackets complete all as specified and as directed. 67 m&l for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. 68 m&l for cast brass pivot suitable for aluminium door, complete all as specified and directed. 69 s&f brass 2lever mortice lock, vertical type, size 100 mm complete all as specified and directed. 70 supply and fix in repair 300mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. 71 supplyand fixin repair bib taps of 15mm bore fancy type, chromium platedcast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule all complete as specified and as directed. 72 supplyand fix in repair angular stop cock of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrulecomplete all as specified and as directed. 73 supplyand fix in repair pillar cock of 15mm bore, cast copper alloy with capstan heads fancy type, chromium plated screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe and fixedcomplete all as specified and as directed. 74 supply and fix in repair 15mm dia stop valve of ptmt any colour high pressure screwed for iron pipe and fixed ( minimum weight 90gms ) complete all as specified and as directed. 75 supply and fix in repair 15mm bore bib tap ( minimum weight 90gms ) standard of ptmt any colour high pressure screwed for iron pipe complete all as specified and as directed. 76 supply and fix in repair 10 litre capacity pvc valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or pvc. 32 mm dia, for low level cistern including pvc connections 15mm size with ptmt nuts and washer both side of length 450mm complete all as specified and as directed. 77 supply and fix health faucet ( abs body ) with 8mm dia 1 meter long flexible tube and wall hook for fixing in 15 mm dia pipe complete all as specified and as directed. make:jaquar or equivalent. 78 supply and fix chromium plated two ways bib cock with wall flange for fixing in 15 mm dia pipe complete all as specified and as directed. make:jaquar or equivalent. 79 suply and fix in repairs stainless steel sink with drainage board made out of 1.00 mm thick sheet for kitchen with plug washers, waste pipe including bedding in cement mortar on dwarf wall or including cast iron cantiliver brackets connecting union overall size 915 x 460 mm with bowl size 405x355x178mm or 410x357x178mm complete all as specified and as directed ( model no.bssbsd 52 of blue star / sbsd 05 of joyna / equivalent brand of prayag ) . 80 supply and fixin repair vitreous china squatting pan, ‘orissa’ pattern, size 580 x 440 mm white, with integral foot rests including por s trap ( excluding flushing cistern and flush pipe ) including provision of lime concrete bedding complete all as specified and as directed. 81 supply and fix in repair vitreous china ewc p or s trap of size 400x365x540mm, white including plastic water closet seat, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device suitable for ewc ( excl flushing cistern and flush pipe ) complete all as specified and as directed. 82 supply and fix in repairs vitreous china wash basin white flat back, size 630 x 400 mm including ptmt waste coupling 32mm dia ( min wt 45 gm ) , 15mm bore ptmt pillar tap, chain and plug and porcelain stopper etc. complete all as specified and as directed. 83 supply and fix in repair brass chromium plated tubular towel rail , 20mm dia, d type, 600mm long between flange fixed with chromium plated brass screws complete all as specified and as directed. 84 supply and fix in repairs pvc connection 15mm size with ptmt nuts of length 600 complete all as specified and as directed. 85 s & f in repairs rotational moulded polyethylene water storage tanks ( cylinderical vertical with closed top ) 1000 ltr capacity, hoisted and fixed in position all as specified including dismantling existing water tank. 86 all as per item no.85 above but 500 ltr capacity. 87 supply and fix in repairs 20mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed. 88 supply and fixing in repair gun metal, globe or gate valves size 20 mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed 89 supply and fix in repair 100mm cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type b1 complete all as specified and as directed. 90 supply and fix in repair chromium plated wall mixer with connecting legs, for fixing in 15 mm dia pipe complete all as specified and directed. make:jaquar or equivalent. ( cat no. flr 5273 upr ) 91 supply and fix in repair chromium plated mixer with connecting legs, for fixing in 15 mm dia pipes over wash hand basin complete all as specified and directed. make:jaquar or equivalent. ( cat no. flr 5169 nb ) 92 supply and fix in repair chromium plated shower 105mm dia round shape single flow with air effect ( abs body and face plate chrome plated with rubit cleaning system ) for fixing in 15 mm dia pipe complete all as specified and as directed.make:jaquar or equivalent. ( cat no. ohs 1719 ) 93 supply and fix in repair chromium plated concealed stop cock with fitting sleeves and adjustable wall flange with seal for fixing in 15 mm dia pipe complete all as specified and as directed. make:jaquar or equivalent. ( cat no. opr 10083 kpm ) 94 supply and fix in repair chromium plated angular stop cock with wall flange for fixing in 15 mm dia pipe complete all as specified and as directed.make:jaquar or equivalent. ( cat no. orp 10053 pm ) 95 supply and fix in repair chromium plated bib cock with wall flange for fixing in 15 mm dia pipe complete all as specified and as directed. make:jaquar or equivalent. ( cat no. 10037 pm ) 96 supply and fix in repair chormium plated pillar cock for fixing in 15 mm dia pipe complete all as specified and as directed. make:jaquar or equivalent. ( cat no. opr 10001 pm ) 97 supply and fix glass shelf 600mm long with cp railings at sides complete all as specified and as directed. make:jaquar or equivalent ( cat no. can 1171 n ) 98 supply and fixtoilet paper holder with flap recessed type ( stainless steel ) complete all as specified and as directed. make:jaquar or equivalent. ( cat no. can 1155s ) 99 dismantling of old unserviceable floor, hearth or wall tiling including cement mortar bedding ( but not backing and rubbish off the premises complete all as specified and as directed. 100 roughnening surface of old concrete floor by picking , sweeping clean and washing down with water to remove dust , etc complete all as specified and directed. 101 material and labour for light shade vitrified tiles 10mm thick ( square / rectangular ) polished, area of each tiles n.exc. 0.36 sqm in floorsetc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 20mm thick screed bed or bedding layer in cm ( 1:6 ) complete all as specified and as directed. 102 material and labour for light shade vitrified tiles 10mm thick ( square / rectangular ) polished, area of each tiles n.exc. 0.36 sqmin skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 10mm thick rendering in cm ( 1:4 ) complete all as specified and as directed. 103 material and labour for non skid ceramiccoloured tiles7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but n.exc. 0.18 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or colouredcement to match the colour of tiles over and including 15mm thick screed bed or bedding layer in cm ( 1:6 ) complete all as specified and as directed. 104 material and labour for glazed ceramic colourtiles ( 300x200 ) x7mm thick in skirting / dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 10mm thick rendering in cm ( 1:4 ) complete all as specified and as directed. 105 demolition of cement concrete in ground floors and pavings n.exc. 15 cm thickness below or above ground level complete all as specified and as directed. 106 demolition of brickwork built in cement mortar including all quoins, arches, pillars etc. complete all as specified and as directed. 107 material and labour for brick work withbricks class designation 75, old size, straight or curved on plan exc 6m mean radius built in cement mortar ( 1:6 ) complete all as specified and as directed. 108 material and labour for brick work with bricks class designation 75, old size, straight or curved on plan to any radius in half brick thick walls built in cement mortar ( 1:4 ) complete all as specified and as directed. 109 taking down cement plaster of any description on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. 110 material and labour for 20mm thick plaster in cement mortar ( 1:4 ) in two layers, i.e 10mm thick in each layer, top layer mixed with integral water proofing liquid admixture as per manufacturers instruction on brick or concrete surfaces of wall finished the surface fair and even complete all as specified and as directed. note : wpc shall be measured and paid separately. 111 supply only integral water proofing liquid admixture for concrete and mortar ( make :conplast x421ic of fosroc / sika no 1 of sika / equivalent brand of pidilite ) 112 material and labour for rendering 15mm thick in cement mortar ( 1:6 ) on fair faces ofbrickwork or concrete surfaces, finished the surface even and smooth without using extra cement complete all as specified and as directed. 113 material and labour for rendering 05mm thick in cement mortar ( 1:3 ) on concrete surfaces in ceiling and finished the surface even and smooth without using extra cement complete all as specified and as directed. 114 m&l for applying 1.50mm thick wall care putty and appling two coats of oil bound distemper over a coat of alkali resistant primer to wall to new plaster surface complete all as specified and as directed. 115 material and labourfor preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primercomplete all as specified and as directed. 116 material and labourfor preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed. 117 all as per item no. 116 above but in ceiling. 118 material and labour for 40mm thick pcc ( 1:2:4 ) type b1 ( using 20mm graded stone aggregate ) as in floors complete all as specified and as directed. 119 supply and fix in repairs pvc ( swr ) pipe 110mm bore, type a, single socketed, in any length with rubber ring joints fixed to walls with and including pvc clip and including taking down existing rain water pipes complete all as specified and as directed. 120 dismantling cast iron drain pipes of any dia and any description, jointed in cement mortar obtained either from trenches / wall as required complete all as specified and as directed. ( note : excavation if required, shall be measured and paid separately ) 121 supply and fix 75mm bore cast iron ( sand cast pipes ) soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall with ms clamp complete all as specified and as directed. 122 supply and fix 100mm bore cast iron ( sand cast pipes ) soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall with ms clamp complete all as specified and as directed. 123 supply and fix 100mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and as directed 124 supply and fix in repairs 75mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and as directed 125 supply and fix in repairs 100mm bore cast iron branch pieces, single ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branches complete all as specified and as directed. 126 supply and fix in repairs 100mm bore cast iron cowls complete all as specified and as directed. 127 m&l for 20mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite , complete all as specified and directed. 128 material and labour for complete removal of existing treatment of old plastered surfaces of wall including washing, rubbing down and stopping of old treatement and applyingtwo coats of oil bound distemper over a coat alkali resistant primer and finished the existing surface with 1.5mm thick wall puttyetc complete all as specified and as directed. 129 material and labour for preparation of old treated plastered surfaces of wall and applying one coat of white wash complete all as specified and as directed. 130 all as per item no. 129 above but in ceiling complete all as specified and directed. 131 demolition of cement concrete of any description including any treatment there to and in any position provided as in roof padding, roof curb etc complete all as specified and as directed.note: ( a ) demolition should be done carefully to roof slab. ( b ) any damage occurred in the roof surfaces during demolition shall be made good by the contractor without extra cost to the department. ( c ) disposal of old debris / retrieved material to outside the premises or as directed by the engineer in charge. 132 material and labour for providing plain cement concrete 1:2:4 type b1 using 20mm graded stone aggregate as in roof padding laid in slope as per requirementmixed with integral water proofing liquid admixture as per manufacturers instructions complete all as specified and as directed.note : ( i ) minimum thickness of pcc shall be 50mm. ( ii ) integral water proofing liquid admixture shallbe measured and paid separately underappropriate item. 133 material and labour for water proofing treatment with app based standard membrane over pcc padding in roof with the following courses of treatment : ( a ) applying bituminous primer ( is 3384 ) @ 0.40 kg per sqm of the surface area including cleaning the surfaces completeall as specified and directed. ( b ) applying app plastomeric bitumen based mineral finished water proofing membranepolyester reinforced ( 4 kg / sqm ) with 10cm over laps and torch bonded at joints including surface preparation before and after application of treatment as per manufactures instruction complete all as specified and directed. 134 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete including fittings and fixtures such as switches, bell push, call bell, ceiling rose, sockets, switch sockets, regulator, lamp holderetc by unscrewing from board carefully and keep aside serviceable materials for reuse including making good of the disturbed surfaces, complete all as specified and directed. 135 material and labour for point wiring ( surface type ) with pvc insulated 1100 volts grade frls unsheathed single core multi stranded copper conductors 1.5 sqmm ( nominal area ) for phase, neutral and 1.5 sqmm pvc insulated unsheathed multi stranded copper conductor cable for earth continuty conductor drawn through and including pvc casing n caping ( medium duty ) double lock type, size of casing caping as required at site but not less than 20mm with fittings and accessories pressed steel sunken terminal box in concealedmade out of 1.6 mm thick ms sheet duly painted with two coats of synthetic enamel paint of approved colour over a coat of red oxide zinc chrome primer and covered with 3 mm thick bakelite sheet cover for fixing switches, sockets, regulator etc and earth continuty conductor shall be connected to common earth and earth dollyfor one light / fan point controled by one, one way 5 amp switch complete all as specified and as directed. 136 all as per item no 135 here in above but for one 3 / 5pin 6amp socket outlet on the same board with other switches complete all as specified and as directed. 137 all as per item no 135 here in above but for one 3 / 5pin 6amp socket outlet on the independent board complete all as specified and as directed. 138 all as per item no 135 here in above but for one call bell point controlled by one bell push switch complete all as specified as directed. 139 all as per item no 135 here in above but for one light point controlled by two 2 way modular switch complete all as specified as directed. 140 all as per item no 135 here in before, for one 15 amps socket outlet but using 2.5 sq mm, copper conductor with 2.5 sq mm, pvc insulated single core cable for earth continuity conductor complete all as specified and directed. 141 m&l for cutting chases, pinning in making good to facing where required and pointing in cement mortar ( 1:3 ) to ends or edges of landing, steps, cills, sunshades sheleves, lintels, etc and cutting chases for concealed water tubing or concealed conduict wiring etc and making good cutting not exc 10 cm grith complete all as specified and directed. 142 supply and fix switch piano flush button 5 / 6 amp single pole, one way complete all as specified and as directed. 143 supply and fix socket outlet 5 pin, 5 / 6 amps flush type complete all as specified and as directed. 144 supply and fixswitch socket combination5 pin, 5 / 6 amp flush type complete all as specified and as directed. 145 supply and fix switch socket combination 5 pin 15 / 16 amp flush type with complete all as specified and as directed. 146 supply and fixing switch flush type, 6 amps, single pole, two way complete all as specified as directed 147 supply and fix lamp holder insulated body with back plate for angle / batten fittings complete all as specified and directed. 148 supply and fix ceiling rose surface bakelite, 65 x 50mm, three terminals complete all as specified and directed. 149 supply and fix bell push, flush type 6 amps complete all as specified and directed. 150 supply and fix electronic fan regulator stepped type flush type ac 240 volt complete all as specified and as directed. 151 supply and fix in replacement call bell ding dong, ac, 230v single pole complete all as specified as directed. 152 material and labour for sub main wiring ( surface type ) with two run of pvc insulated, unsheathed, frls single core, multistranded copper conductor of size 4.0 sq mm and one run of 4.0 sqmm copper conductor as continuity earth wire, drawn through and includingpvc casing caping including taking down old sub main wiring with casing caping complete all as specified and directed. ( note:two run of 4.0 sqmm copper conductor cable, one run of 4.0 sqmm earth continuity cable and one run of pvc casing capping shall measured as one unit ) . 153 material and labour for sub main wiring ( surface type ) with two run of pvc insulated, unsheathed, frls single core, multistranded copper conductors of size 6.0 sq mm and one run of 6.0 sqmm copper conductor as continuity earth wire, drawn through and including pvc casing caping including taking down old sub main wiring with casing caping all as specified and as directed. ( note:two run of 6.0 sqmm copper conductor cable, one run of 6.0 sqmm earth continuity cable and one run of pvc casing capping shall measured as one unit ) . 154 material and labour for sub main wiring ( concealed type ) with two run of pvc insulated, unsheathed, frls single core, multistranded copper conductors of size 4.0 sq mm and one run of 4.0 sqmm copper conductor as continuityearth wire, drawn through and including pvc conduit ( medium grade ) of adequate sizewith fittings and accessoriesas required at site and taking down old sub main wiring with conduit complete all as specified and as directed. note: ( note:two run of 4.0 sqmm copper conductor cable, one run of 4.0 sqmm earth continuity cable and one run of pvc conduit shall measured as one unit ) . ( ii ) cost of cutting of wall, if any, for housing ofgi box and also making good the disturbed surfaces are deemed to be included in unit rate. 155 material and labour for sub main wiring ( concealed type ) with two run of pvc insulated, unsheathed, frls single core, multistranded copper conductors of size 6.0 sq mm and one run of 6.0 sqmm copper conductor as continuityearth wire, drawn through and including pvc conduit ( medium grade ) of adequate sizewith fittings and accessoriesas required at site and taking down old sub main wiring with conduit complete all as specified and as directed. note: ( i ) :two run of 6.0 sqmm and one run of 6.0 sqmm copper conductor ( for phase, neutral and earth ) +one run pvc conduit shall measured as one unit ) . ( ii ) cost of cutting of wall, if any, for housing ofgi box and also making good the disturbed surfaces are deemed to be included in unit rate. 156 supply and fix in repair powder coated sheet metal enclosure ( in concealed ) single pole & neutral for dbs ( double door ) 4 way, 240 v with 200 amps rated busbar din channel, neutral link & earth link superline complete all as specified as directed. 157 all as per item no 156 here in above but for 8 way spn db complete all as specified as directed. 158 all as per item no 156 here in above but for 12 way spn db complete all as specified as directed. 159 supply and fix of 4 way vertical type tpn db in double door suitable for four pole mccb as incomer including make good of damaged surface / wall including re connection with existing earth wire to db incuding taking out the oldunserviceable one complete all as specified and as directed.make: havells cat no. dhdlvdrwgofo04 / ltvd04n of l&t / indoasian cat no.811888 / equivalent makes specified in ps to tender document. 160 supply andfix mccb four pole63 amps, 240 volts, 16 ka, with all incoming / outgoing connections suitablefor fix 4 way vertical type tpn db in double doortwith proper size of aluminium lugs complete all as specified as directed make: havells cat no. ihlgnf0063 / indoasian cat no. 830006 / c&s / equivalent makes specified in ps to tender document. 161 supply and fix sheet metal enclosure / tpndbs ( double door ) 4 way with 200 amps rated busbar suitable for mcb including taking down old unserviceable enclosure one complete all as specified and directed. 162 supply andfix mcb triple pole & neutral 63 amps, 240 volts, 10 ka, c series with all incoming / outgoing connections suitablefor4 waytype tpn db in double door ( itrm no 36 ) with proper size of aluminium lugs completeall as specified and directed . 163 supply andfix in repair, mcb triple pole & neutral 63 amps, 240 volts, 10 ka, c series with all incoming / outgoing connections suitablefor 4 way type tpn db in double door ( itrm no 36 ) twith proper size of aluminium lugs completeall as specified and directed . 164 supply andfix mcb single pole & neutral 6 to 32 amps, 240 volts, 10 ka, c series with all incoming / outgoing connections with proper size of aluminium lugs completeall as specified and directed. 165 supply and fix, in repair, mcb single pole & neutral 6 to 32 amps, 240 volts, 10 ka, c series with all incoming / outgoing connections with proper size of aluminium lugs complete all as specified and directed. 166 supply and fix mcb single pole6 to 32 amps, 240 volts, 10 ka, c series with all incoming / outgoing connections with proper size of lugs completeall as specified as directed. 167 supply andfix in repair, mcb single pole6 to 32 amps, 240 volts, 10 ka, c series with all incoming / outgoing connections with proper size of lugs completeall as specified as directed. 168 material and labour for earthing with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground ( earth pit not less than 2.25 mtrs deep below gl ) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, earth lead wire protected by and including 15mm dia gi pipe ( light grade ) and 20mm dia gi pipe ( medium grade ) for watering and connected to control switch as directed including necessary earthwork as in soft / loose soil, concrete pit in pcc ( 1:3:6 ) type c1, pre cast rcc ( 1:1.5:3 ) type a1 cover slab duly reinforced with 8mm dia tmt bar @ 150mm c / c both way and two nos lifting handle made of 8mm dia tmt bar and set in cement mortar ( 1:4 ) , funnel, wire mesh, char coal or coke and salt in alternate layer, testing, etc complete and as specified in electrical plate no 3 of ssr pt i including taking down old earthing complete all as specified and directed. 169 supply and fix gi wire as earth continuity conductor including taking down old unserviceable earth wire compleate all as specified and as directed. 170 supply andfix gi pipe 15 mm bore ( dia ) , light grade for protection of earth electrode including taking down old unserviceable gi pipe complete all as directed and as specified. 171 s&f led tube light fitting, 1 x 18 watt, 4 feet, 220 volt ac decorative type with driver holder and led lamp including connecting up with three core flexible cable copper conductor including taking down old unserviceable light fitting all as specified and directed. 172 s&fled building security light fitting 35 watt energy saving versatile pressure die cast aluminium ip65 building security luminaire with suitable gi bracketcomplete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230v, 50 hz complete including taking down old unserviceable light fitting all as specified and directed. 173 s&f led post top lantern with post top made in cast aluminium spigot housing with decorative opal acrylic diffuser and ip 65 protection including 40 watt led lamp with all accessories and fixing in existing post including taking out old unserviceable / broken light fittings complete all as specified and directed. 174 material and labour for point wiring ( concealed type ) with pvc insulatedfrls ( fire reatrdant low smoke ) cable 1100 volts grade unsheathed single core multi stranded copper conductors 1.5 sqmm ( nominal area ) for phase, neutral and 1.5 sqmm pvc insulated unsheathed multi stranded copper conductor cable for earth continuty conductor drawn through and including pvc conduit ( medium grade ) of adequate sizewith fittings and accessoriesas required at site including suitable size of modular gi boxes of thickness not less than 0.8 mm thick with suitable size of modular inner and outer cover combine plate and accessories complete for fixing of modular switches, sockets, regulator etc and earth continuty conductor shall be connected to common earth and earth dolly for one light / fan point controlled by one way modular switch complete all as specified and directed.note : ( i ) cost of cutting of wall, if any, for housing of modular gi box and also making good the disturbed surfaces are deemed to be included in unit rate. ( ii ) cost of modular gi box of suitable module and suitable outer & inner combined cover plate shall be deemed to be included in the qouted rate. 175 all as per item no 174 above but for one 3 / 5 pin 6 amps socket outlet on the same board with other switches complete all as specified and directed. 176 all as per item no 174 above but for one 3 / 5 pin 6 amps socket outlet on the independent board complete all as specified and directed. 177 all as per item no 174 above but for one call bell point control by one bell push switch complete all as specified and directed. 178 all as per item no 174 above but for one light point controlled by two 2 way switch complete all as specified and directed. 179 material and labour for point wiring ( concealed type ) with frls pvc insulated 1100 volts grade unsheathed single core multi stranded copper conductors 2.5 sqmm ( nominal area ) for phase, neutral and 2.5 sqmm pvc insulated unsheathed multi stranded copper conductor cable for earth continuty conductor drawn through and including pvc conduit ( medium grade ) of adequate sizewith fittings and accessoriesas required at site including suitable size of modular gi boxes of thickness not less than 0.8 mm thick with suitable size of modular inner and outer cover combine plate and accessories complete for fixing of modular switches, sockets, regulator etc and earth continuty conductor shall be connected to common earth and earth dolly for 3 / 5 pin 16 amps socket point on independent board complete all as specified and directed.note : ( i ) cost of cutting of wallfor housing of modular gi box, conduit and making good the disturbed surfaces are deemed to be included in unit rate. ( ii ) cost of modular gi box of suitable module and suitable outer & inner combined cover plate shall be deemed to be included in the quoted rate. 180 supply and fix modular switch 1 way, 6 a, 1 module including modular white cover plate with frame complete all as specified and as directed. 181 supply and fix modular switch 1 way, 16a, 1 module including modular white cover plate with frame complete all as specified and as directed. 182 supply and fix socket 6a 2 / 3 pin combined 2 module including modular white cover plate with frame complete all as specified and as directed. 183 supply and fixsocket 6a / 16a, 2 / 3 pin combined 2 module including modular white cover plate with frame complete all as specified and as directed. 184 supply and fix modular switch 2 way, 6 a, 1 module including modular white cover plate with frame complete all as specified and as directed. 185 supply and fix fan regulator modular type120 w, 2 module complete all as specified and as directed. 186 supply & fix bell push switch designer modular type 1 module complete all as specified and directed. 187 supply and fixing sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug socket and plug top 20 amp complete with one single pole mcb 20 amp complete all as specified and directed. 188 taking down geysers of any make / model / type / capacity after disconnecting all electrical and water supply line for repair / replacement of parts and components, refixing in old position after repair / replacement complete all as specified and as directed.note: i ) the unit rate quoted is deemed to include for the labour element involved in replacing the spares as mentioned herein below. ( ii ) the spares replaced shall be measured and paid as supply only items herein below. ( iii ) the spares shall suit the exisiting makes of geyser or as per existing make of spares, as approved by the ge.existing makes of geyser: bajaj, peon 189 supply only apparatus assembly plate ( 8 / 9 hole ) for geyser of 25 ltrs / 50 ltrs capacity ( as per existing sample ) complete all as specified and directed. 190 supply only thermostat straight stem type complete all as specified and directed.make : bajaj / elcon / girish / ego. 191 supply only heating element 1500 watt suitable for geyser of 25 ltrs capacity triangular / round type complete all as specified and directed. make : bajaj / rex / as per existing make 192 supply only indicating ( red / green ) lamp led type ( square / round ) button type for geyser of 25 / 50 ltrs capacity complete all as specified and directed. 193 supply only pvc flexible cold water inlet pipe 15 mm dia 600 mm long complete all as specified and directed. make : make: prince / supreme / prayag / polytuf / . m / s sak plast pvt ltd. 194 all asperitem no. 194here in before but hot water pipe ( inlet wiremess type ) complete all as specified and directed. 195 supply and fix in repair of chromium plated stop cock 15mm bore including taking down old unserviceable cast copper alloy stop cock complete all as specified and as directed. . 196 supply and fix in repair of round type 3 core incoming copper cable of size 2.5 sqmm for 25 / 50 ltrs capacity geyser complete all as specified and as directed. 197 taking down carefully ceiling fans of any make, model and capacity from their existing places for servicing i. e. lubricating / greasing and for rewinding / painting by dismantling the same and keep the blades, canopy, splitpin and other parts and components in safe custody and hanging / fitting on its previousposition after repair / rewinding / painting / replacement of spares etc complete all as specified and directed.note: i ) the unit rate quoted is deemed to include for the labour element involved in replacing the spares as mentioned herein below. ( ii ) the spares replaced shall be measured and paid as supply only items herein below. ( iii ) the spares shall suit the exisiting makes of geyser or as per existing make of spares, as approved by the ge. ( iv ) rewinding and painting shall be measured and paid separately.existing makes : bajaj, khaitan, usha, himadri 198 all as per item no. 197 above but exhaust fan, any make, model andsize complete all as specified and directed.existing makes : orison, garg udyog 199 all as per item no. 197 above , but wall mounted, any make, model andsize complete all as specified and directed.existing makes : bajaj 200 supply only gm bush for ceiling fan 1200 / 1400 mm sweep complete all as directed. 201 supply only gm bush for exhaust fan 230 / 300 / 350 / 450 mm sweep complete all as specified and directed. 202 supply only ball bearing ( cat no. 6201 ) for ceiling fan / exhaust fan complete all as specified and directed.make: skf / nbc / any other reputed make as approved by the ge, 203 all as per item no. 202 above but cat no. 6202 complete all as specified and directed. 204 all as per item no. 202 above but cat no. 6203 complete all as specified and directed. 205 supply and fix in repair capacitor 2.5 mfd, 220 volts complete all as specified and directed.make: tipcon / universal / usha / bajaj / cg / 206 all as peritem no. 205above but 3.0 / 4.0 mfd complete all as specified and directed. ( make:tipcon / universal ) 207 supply and fix in repair of louver shutter for 300 mm sweep exhaust fan made of ms sheet folded type complete all as specified and directed.make: orison, garg udyog 208 allas peritem 207 here in before but for 450 mm sweep exhaust fan complete all as specified and directed.make: orison, garg udyog 209 material and labour for painting by spraying with synthetic enamel paint, first quality, glossy finish, to ceiling fans, any make, model andsize, including blades / down rods / canopy / stand, casing / cage andall accessories after preparation of surfce including thoroughly rubbing / cleaning old rusted spot complete all as specified and directed. 210 all as per item no. 209 above but fo exhaust fans, any make, model andsize complete all as specified and directed. 211 all as per item no. 209 above but forwall mounted fans, any make, model and size complete all as specified and directed. 212 material and labour for rewindingof ceiling fans armature of 1200 mm / 1400 mm sweep of any make & model with replacing the burntout winding by new super enameled high grade copper wire of existing gauge and number of turns and all insulating materials including heat vernishing and testing complete all as directedmake of wire finolex / kei / havells / icc / devidayal / kei / hpl / c&s / rr kabel.. 213 all as peritem no. 212 above but for exhaust fan 230mm / 300mm sweep, single phase, 230 volts complete all as specified and directed. 214 all as peritem no. 212 above but for exhaust fan 450 mm sweep, single phase, 230 volts complete all as specified and directed. 215 all as peritem no. 212 above but for wall mounted fans single phase, 230 volts complete all as specified and directed. 216 supply and fix in repair fan blades for exhaust fan of 300 mm sweep as per existing make and type complete all as specified and directed. 217 all as per item no. 216 above but for exhaust fan of 450 mm sweep complete all as specified and directed. 218 s&f in repair of incoming twin core copper flexible wire of size 14 / 0.0076from ceiling rose to ceiling fan / exhaust fans complete all as specified and directed.make : finolex / havells / polycab / kei / hpl / rr kabel / mescab. 219 supply and fix in repair 3 pin plug top 5 amps complete all as specified and directed. make : anchor / havells / crabtree / c&s / hpl / cona / bajaj. 220 supply and fix in repair 3 pin plug top 15 amps complete all as specified and directed.make : anchor / havells / crabtree / c&s / hpl / cona / bajaj. 221 s&f led tube light fitting of 2 feet long but replacing of the ftl fitting of 20 wattwith energy saving led luminarries fitting of 10 watt including taking down old unserviceable led fitting complete all as specified and as directed....

Military Engineer Services - West Bengal

38895725 tender for provision of addl point wiring for md accommodation, provision of hard standing ( 30 sqm ) near bldg no p 16 , provision of 03xsentry post near mt park, gun par and office complex, provn of bathroom & toilet near bldg no t 88, t 12 & t 22 at raspunja mil station under ge ( central ) kolkata. 1 surface dressing not exc. 150mm deep and getting out in soft / loose soil, complete all as specified and as directed. 2 surface excavation not exc. 30 cm deep and ave. 15 cm deep and getting out in soft / loose soil, complete all as specified and as directed. 3 excavating in trenches, n exc 1.50 m wide and n exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft and loose soil complete all as specified and directed. 4 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft / loose soil complete all as specified and directed. 5 removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point as in soft / loose soil complete all as specified and directed. 6 m&lhardcore ( broken stone or boulders ) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 7 m&lsand filling under floors or in foundations including watering and consolidation complete all as specified and directed. 8 m&l treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface ( area of the sub structure in contact with backfill to be measured ) complete all as specified and directed. 9 m

Public Works Department - West Bengal

38827662 tender for installation of aluminium alloy frame partition walls, swing doors at 3rd floor of pwss sub division office building at kapasia, gopiballavpur along with one no jail type gate for stair room during 2023 24....

Public Works Department - West Bengal

38827635 tender for installation of aluminium alloy frame sliding door and window, stainless steel railing at lift machine room and water tank room of pwss sub divisional office building at kapasia, gopiballavpur under jhargram division pwd during 2023 24...

Indian Army - West Bengal

38799142 spare part for geg ssl , alluminium alloy gde 64430 r / bar dia 80 part no nk , steel plate carbon h / r 2200 x 900 x 8 mm part no nk => limited...

Military Engineer Services - West Bengal

38719242 tender for additional /alternator and special repairs to offer md accommodation under ge alipore kolkata, taking down cement plaster including raking out joints, hacking for key, scrubbing down with water etc complete. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , demolition of brickworkquoins, arches, pillars etc but excluding ashlar facings, dressed all store work and precast concrete articles built in cement mortar. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for brick work with sub class b bricks built in cement mortar 1:6 straight or curved on plan exceeding 6 mtr mean radius and all as directed. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for brickwork with sub class `b’ bricks, straight or curved on plan to any radius in half brick thick walls built in cm ( 1:4 ) . ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , demolition of rcc ( reinforcement ) of any description and in any position not otherwise specifically provided for . ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , use and waste of formwork to sides of column, pillars, posts, stanchions for rough foinished surface complete all as specified and as directed by the engr in charge. ( upto 04 storey of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , use and waste offormwork to sides and soffit of beams, lintels, cantilevers, shelves etc for rough finished surface complete all as specified and as directed by the engr in charge. . ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , use and waste offormwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railing horizontal or sloping and similar work exe 5 cm but not exe 10 cm thick completeall as specified and as directed by the engr in charge. . ( upto 04 storey highof building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , use and waste offormwork to chullah hoods, chajjas, troughs, parapets and similar items including edges for rough finished surface complete all as specified and as directed by the engr in charge. . ( upto 04 storey of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for rcc form 20 ( design mix ) using 12.5 mm graded crushed stone aggregateas in parapets, balcony andsimilar workall as specified and directed ( upto 04 storey highbuilding ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , chipping of unsound / weak concrete materials from slabs , beams, columns , lintel, chajja, fin , facia etc. by any means as directed by engr in charge including tapering all edges, making square shoulders of cavities air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting incl foreign matrials , loose concrete / aggregate etcand disposal of all debris out of mod land and complete all as specifiedandas directedby engr in charge ( upto 4 storey of building ) for 25mm average thickness for slabs / chajja , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , all as per item above but 50 mmaverage thickness for beams / lintel , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , all as per item above but 60mmaverage thickness for column , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , all as per item above but add or deduct for every 10 mm thickness extra , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , removing of concrete all around reinforcement including from behind the reinforcing bars to give an average 25mm ( but not less than 15mm clear air gap ) by manual methods ( using wire brushing , chiselling etc ) and applying alkaline rust removing chemical followed by removing rust including from behind the reinforcing bars by emery paper and cleaning the area throughly by water and allow it to dry all as per manufacturer, s instruction to give it a totally rust free finished steel surface complete all as specified and directed by engr in chargeupto 12 mm dia bar ( upto 4 storey of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m & l for providing single coat of epoxy bond adhesive of prepared non metallic surface ( existing surface ) and applying by brush all as per manufactures instruction / specification. the bonding agent shall have minimum compressive strength of 40 n / sqmm and complete all as specified and directed by engr in charge ( upto 4 storey of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , supply and application of epoxy zinc rich primer on the prepared steel surface by brush the primer shall have a minimium specific gravity 1.75 minimum weight film thickness / coat 40 microns and minimum adhesive bond strength with steel is 1.5n / mm2 complete all as specified and directed by engr in charge ( upti 04 storey building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to12 storey , m & l for introducing new reinforcement bars for structural connection in rcc beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc all as specified and directed by engr in charge. upto12 mm dia bar upto 4 storey high. , all as per item abovebut 5 storey to 8 storey , all as per item abovebut 9 storey to 12 storey , m & l for providing and inserting mild steel shear key bars / levelling gauges of required length and diameter in reinforced / plain concrete as per drawing and direction of engr in charge including power drilling holes of appropriate diameters to a minimum depth equal to 12 times the diameters of shear key bar / levelling gauge, cleaning the drilled holes of loose dust by blowing , insertion of epoxy from cartridge, placing the shear key bar in position and allowing it to stay undisturbed for 24 hours. rate shall be include cost of labour, all materials, t&p for power drilling in concrete , epoxy cartridge, plastic nozzle etc, complete incl cleaning the drilled holes of loose dust by blowing air complete all as spd and dir by engr in charge. 12 mm dia, 300mm long @ ms shear key of bar . the projection length of shear key shall be more than 10 times its diameter plus half of the thickness of cover to concrete plus bend length. ( upto 4 storey high ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m & l for providing and placing in position free flow non shrink cementitious micro concrete of grade of m 50 to the effectedcolumn etc . the micro concrete shall have a minimium 1 day compressive strength of 10 mpa and 28 days strength of 50 mpa, minium tensile strength 5n / mm2 @ 28 days, minimium flextural strength 5n / mm2 @ 28days and complete all as spd and dir by engr in charge.60 mm average thickness of column, upto 4 storey high. makesika / hindcon / fosroc or its equivalent , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m & l for providing and placing in position free flow non shrink cementitious micro concrete of grade of m 50 to the effected beam, etc . the micro concrete shall have a minimium 1 day compressive strength of 10 mpa and 28 days strength of 50 mpa, minium tensile strength 5n / mm2 @ 28 days, minimium flextural strength 5n / mm2 @ 28days and complete all as spd and dir by engr in charge50 mm average thickness of beam, upto 4 storey high. , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m & l for providing and placing in position free flow non shrink cementitious micro concrete of grade of m 50 to the effected beam, column etc . the micro concrete shall have a minimium 1 day compressive strength of 10 mpa and 28 days strength of 50 mpa, minium tensile strength 5n / mm2 @ 28 days, minimium flextural strength 5n / mm2 @ 28days and complete all as spd and dir by engr in charge.add or deduct for every 10 mm thickness extra, upto 4 storey high. , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to12 storey , supply, mixing and application two component structural grade polymer modified reinstatement morter, where local spalling has taken place or shuttering is not possible . the morter can be applying in layers not exceeding 6mm thick in each layer in and upto any thickness in smaller vertical pockets and upto any thickness in horizontal applications. the mortar should have a minimium compressive strength 12n / mm2 in 1 day and 45n / mm2 in 28 days. minimum flexural strength should be 8 n / mm2 in 28 days. a modified styrene butadience emulsion for use as a bonding aid and gauging liquid for cementious system to be mixed with cement slurry before the application of modified polymer mortar to be used @ 6 ltr / bag of cement. the bonding agent should have minimium compressive strength 24n / mm2. minimum tensile strength 3.5n / mm2, minimium flexural strength 6.5n / mm2 complete all as spd and directedby the engr in charge upto 25 mm average thickness and upto 4 storey highnote: cement and sand morter in proportion of 1:2 graded coarse sand ) with polymer admixed in proportions approved by engr in charge. , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m & l for applying curing compound over concrete surfaces as per manufactures instruction complete all as spd and dir by engr in charge upto4storey high . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , providing of double layer self supporting steel scafolding to external perimeter of building duly cross braced and properly alignede for the functional aspect and safe of the building upto and including 15m hieght complete all as specified and as directed. , providing ofdouble layer self supporting steel scafolding to external perimeter of building duly cross braced and properly alignede for the functional aspect and safe of the building exceeding 15m height but not exceeding 45m height complete all as specified and as directed. , materials and labour for providing and inserting 12mm dia aluminium / gi injection nipples along crack line honey combed area including drilling holes as required diameters upto depths from 40mm to 80mm or half the thickness of member ( whichever is less ) at required spacing as approved by ge for the concrete work surface upto 12 storied building complete all as specified and as directed. , materials and labour for making grooves of size 12mmx12mm along the crack line, making the crack dust free by blowing compressed air and then washing with water, finnaly sealing the distance between the injection nipple with approved putty ( polymer modified cement mortar / polyster putty ) etc. and allow to cure. if cementitous grout the materail proposed to be used, washing and saturating the cracked surface with water by pumping from top most nipple and down wards and curing of putty upto 12 storied building complete all as specified and as directed. , supply and applying two coats of high performance elastomeric cementitious waterproof coating sandwiched with 45 gsm glass fibre reinforcement on the entire floor and 1.0 m of all walls of all toilets as per following methodology: cleaning of exposed concrete surface by mechanical means or by hydro blasting to remove laitance, loose particles, contamination etc. which may hinder bonding. coving of rcc joints with pcc ( 1:1.5:3 ) mixed with integral water proofing compound. applying one coat of waterproofing membrane to concrete surfaces followed by application of 45gsm glass fibre on the wet surface. applying second coat of waterproofing membrane at the right angles to the direction of first coat. second coat shall be applied after the first coat gets dry. sprinkling fine aggregate immediately after the application of second coat to get the mechanical key for protective plaster. curing to water proofing membrane to be carried out for minimum period of 3 days with ponding complete. the water proofing product should have mixed density: 1.68g / cc ( brushable consistency ) .adhesion to concrete : >1n / mm2. static crack accommodation: 1mm ( upto04 storey highbuilding ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&fshear connector of 8mm dia & requisite length on the surface to be repaired for the bonding between old and new concrete as per the locations instructed by the engr in charge. the shear connectors shall be of l shape and welded with existing reinforcement at least 100mm in length @ 200mm c / c both horizontally and vertically followed by coat of epoxy zinc primer as per the specification mentioned in complete all as specified and as directed. ( upto 04 storey ht of bldg ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f tmt bars 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f tmt bars 8 mm dia and over as in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , demolition of cement concrete of any description and in any position not other wise specifically provided for complete all as specified and as directed. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for rendering 15mm thick in cm ( 1:6 ) onother than fair face of brick work or concrete surfacesand finished the surface even and smooth without using extra cement complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for rendering 20mm thick in two layers ( top 10mm thick rendering coat mixed with water proofing compound applied as per manufacturers instructions shall belaid over 10mm thcik plastered surface ) with cm ( 1:4 ) on fare faces of brick work or concrete surfaces finishedthe surface even and smooth without using extra cement complete all as specified and as directed by engineer in charge.. . ( upto 04 storey high of building ) note: wpc shall be measured and paid separately , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for rendering 5mm thick with cm ( 1:3 ) on or concrete surfaces and finished the surfaceeven and smoothas in ceiling complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to12 storey , material and labour for complete removal of existing old surfaces of wall and preparation of old or previously untreated surfaces andone coat alkali resistant primer, sanding the surfaces andmaterial & labour for applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives1.43 litre / 10 sqm over upto four storied building complete all as specified and as directed. , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m / l preparation of new plastered surface and applying three coats of white wash on ceiling complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 8 storey12 , m / l preparation of old surface and applying one coats of white wash on ceiling to match with the new one complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m / l preparation of new plastered surface and applying two coats ofdistemperoil emulsion over a coat of primer complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m / l preparation of old decorated surface by complete removal of existing treatment, washing, rubbing, stopping etc and applying two coat of oil emulsion distemper over a coat of primer to match with the new suface on wall. complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , supply only integral liquid water proofing compound ( isi mark ) . , dismantiling of floor hearth or wall tiling incl cement mortar ( but not backing ) , and rubbish off the premises ( out of mod land ) , complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for light shade vitrified tiles 7 to 8 mm thick ( square / rectangular ) area of each tiles exceeding not exc 0.36 sqm , in floor etc. set and jointed in neet cement slurry and pointed white or coloured cement to match the light shade of the tiles, over and including screed bed or bedding layer15 mm thick in cement mortar ( 1:6 ) for laying floor finishes complete all as specified and as directed by engineer in charge . ( upto 4 storey of building ) , ditto all as item no.abovebut from 5 storey to 8 storey of building , ditto all as item no.abovebut from 9 storey to 12 storey of building , ditto all as item no. above but as in skirting over and including backing coat / screed bed or bedding layer of mortar 10 mm thick in cement mortar ( 1:4 ) as in dado / skirting complete all as specified and as directed by engineer in charge. ( upto 4 storey of building ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , roughening of surface of old concrete floor by picking , sweepingclean and washing down with water to remove dust etc complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per item abovebut 5 storey to 8 storey , all as per item abovebut 9 storey to 12 storey , non skid ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm infloors etc. set and jointed in neat cement slurry andpointed in white or colouredcement to matchthe shade of tilesover and including screed bed or bedding layer15 mm thick in cement mortar ( 1:6 ) for laying floor finishes complete all as specified and as directed by engineer in charge . ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , ditto all as item no. above but as in skirting over and including backing coat / screed bed or bedding layer of mortar 10 mm thick in cement mortar ( 1:4 ) as in dado / skirting complete all as specified and as directed by engineer in charge. ( upto 4 storey of building ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , glazed ceramic tiles in vertical surface450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchthe shade of tiles .complete all as specified and as directed by engineer in charge. ( note: screed bed shall be measured and paid seperately under respective items of sch a ) ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , backing coat / screed bed or bedding layer of mortar 10 mm thick in cement mortar ( 1:4 ) as in dado / skirting complete all as specified and as directed by engineer in charge. ( upto 4 storey of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for 18 to 20 mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like over and including 15mm thick cement mortar bedding ( 1:6 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite including dismantling complete all as specified. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situationscomplete all as specified and as directed by engr in charge.. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , taking up or down 15mm steel tubing and connections, including cleaning for removal .. ( upto any storey high of building ) , s&f cpvc pipes 20 mm outer diameter of sdr 11 & plain cpvc sdr 11 including necessary brass fittings and fixers to conect / receive gi pipes / brass taps as in walls, ceiling, floor, etc. complete all as specified. ( upto 12 storey high of building ) , taking up or down 20mm steel tubing and connections, including cleaning for re fixing or removal. ( upto 04 storey high of building ) , s&fcpvc pipes 25 mm outer diameter of sdr 11 & plain cpvc sdr 11ncluding necessary brass fittings and fixers to conect / receive gi pipes / brass taps as in walls, ceiling, floor, etc. complete all as specified. ( upto 12 storey high of building ) , s&f25 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed by engineer in charge. ( upto any height of building ) , s&f in repair 15mm bore brass cpbib cock fancy type with qtr turn or half turn chromium plated with crutch or butterfly handle, screwed down, screwed for iron pip or for brass ferrule and complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f in repair 15mm bore brass cp angular stop cock type with crutch or butterfly handle complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f in repair pvc connection 15 mm sizepipe withptmt nut of length 600 mm complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f in repair brass cp shower roses with or without swivel joints, with shower arm, 125mm size, includingfixing to steel pipes or union complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f in repairs vitreous china wash basin ( white ) , flat back, size 580 x 450 mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets, complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f in repair 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by engineer in charge.. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , supplying and laying of cpvc pipes 40 mm outer diasdr 11 & plain cpvc sdr 11 fittings in wallcomplete all as specified. complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 32 mm bore waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end beddedinred leadcement and other end fixedcomplete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 32 mm bore brass cp bottle traps for wash basin with inlet and outlet screwdfor pipe and connections incl nessesary packingcomplete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s & f in repair vitreous china squatting pan of orissa pattern long pan of size 580 mm x 440mm with integral foot rest white with cast iron p or s trap with back inlet includingflush pipe of suitable length to connection with existing cistern & make good complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , supplying only 10 litres capacity pvc valveless, syphonic action type, flushing cistern, white colour, low level, white with inlet, ball valve, float and handle including brackets duly painted, 32mm dia pvc flush pipe complete all as specified and as directed by engineer in charge.. ( upto 04 storey high of building ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f in repair stainless steel kitchen rack / plate rack of size31x36x10 , made of stainless steel sheet 0.63 mm thick etc complete all as specified and as directed by engineer in charge.. ( upto 04 storey high of building ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&fpvc ( swr ) floor trap of 100mm dia, includingjointing to waste pipe fixed in cement concrete, ( 1:2:4 ) type b1 ( using 20 mm graded crushed stone aggregate ) . .complete all as specified and as directed by engineer in charge.. ( upto 04 storey high of building ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f cp grating of 100mm dia, fixed with cement mortar ( 1:3 ) .complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for pcc 1:5:10 type e2 ( using 40mm graded crushedstone aggregate ) as in filling sunken floor complete all as specified and as directed by engineer in charge.. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l 25mm thick pcc 1:2:4 type b 1 ( using 20 mm graded crushed stoneaggregate ) as inflooring complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l 40 mm thick pcc 1:2:4 type b 1 ( using 20 mm graded crushedstone aggregate ) and concrete surface is to be finished even and smooth using extra cement complete all as specified and as directed by engineer in charge.. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , taking down chowkat with shutter ( without taking off shutters from the frame ) n. exc 1.5 sqm each complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f solid pvc door frame of size 50mm x47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing but wood grain printed pvc sheet used instead of plain colour pvc sheet & edges will be painted to match with printed sheetcomplete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f factory made solid pvc moulded door shutter, with particle board core, 28 to 30mm thick ( stiles ) , with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face & 2mm plain colour pvc sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 200 mm long aluminium anodised, barrel tower bolts of extruded section all as specified and as directed ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 150 mm long aluminium handles, cast type, anodisedcomplete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&fstainless steel ball bearing 100 mm long butt hinges, extruded aluminium alloy steel hinge pin, anodised and fixed, type c 21 complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per item no above but 5 storey to 8 storey , all as per item noabovebut 9 storey to 12 storey , supply & fixing stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with ss wire staples complete, all as specified and directed.complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , supplying and fixing mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, railings and similar work conforming to fe 290 gde e 165, complete all as specified and as directed and design / shap approved by by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , material & labour preparation of new steeland iron surfaces of any description areaexc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat ofred oxide and zinc chrome primer, complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for cement concrete ( 1:2:4 ) type b1 ( using 20 mm graded crushed stone aggregate ) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , dismantling cast iron or re inforced concrete drain pipes including fittings of 100mm bore, jointed in cement mortar complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , dismantling ac ( swr ) pipe up to 150 mm boreincluding all fittings, heads, shoes, swan necks etc complete all as specified and directed by the engr in charge. ( upto 4 storey of building ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f 110mm bore pvc ( swr ) pipe single socket in any length rubber ring joints complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 75mm bore pvc ( swr ) pipe single socket in any length rubber ring joints complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 110mm bore pvc ( swr ) pipe bend single socket complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 110mm bore pvc ( swr ) pipe ( single t ) equal or unequalwith acess door complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 110mm bore pvc ( swr ) pipe ( branch piece ) single ( single y ) equal or unequal complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 110mm bore pvc ( swr ) pipe ( swr ) vent cowl complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 75mm bore pvc ( swr ) pipe bend single socket complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 75mm bore pvc ( swr ) pipe ( single t ) equal or unequalwith acess door complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 75mm bore pvc ( swr ) pipe ( branch piece ) single ( single y ) equal or unequal complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , material & labour preparation of old painted wooden surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by engineer in charge ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , material & labour preparation of old painted steel surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by engineer in charge ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , supply and fixing4.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each panecomplete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads ( upto 12 storey high of building ) , supply and fixing4.0 mm thick frosted sheet glass, ordinary quality and glazing with oil putty in squareexc 0.5 sq. m in each pane complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , taking down window / door shutter area exc 1 sqm but n exc 2 sqm each complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , taking down chowkat with shutter ( without taking off shutters from the frame ) areaexc 1.5 sqm but n.exc 4 sqm eachcomplete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 2nd class hw plain, solid, straight chowkats and frames, wrought framed rebated on the solid, rounded or chanfered, put together with glue pinned at joints all asspecified and as directed. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 40 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side. ( upto 04 storey hight of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 35mm thick 2nd class hard wood gauged & skelton shutter, open rebated & prepared to receiv e gauged, ( without sase bar ) eadge of framing plain, chamford or rounded, fitted with cut & mitred beads for securing gauged etc, all as specified and directed. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s& f 50 mm long butt hinges medium weight cold rolled mild steel and fixed all as specified and directed. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s&f 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast al alloy all asspecified and as directed.. ( upto 04 storey high of building ) , all as per item noabovebut 5 storey to 8 storey , all as per item noabovebut 9 storey to 12 storey , m&l for two coats of synthetic enamel paint over a coat of pink primer areaexc.10cm width or girthover new wooden surfacesincluding preparationof surface complete all as specified and as bdirected by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , m&l for 25x4mm size mild steel flat iron as in hold fast conforming to fe 290 gde e 165 complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) . , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s & f second class hard wood beads, straight ( n exe 3 sq cm ) for glazed or gauzed joinery, renewed, including mitres etc complete al as specified and as directed by engineer in charge. , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , taking down door shutter exe 1 sqm and n exe 2 sqm each after including refixing in same opening ( upto 04 storey hight of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , taking down existing roof treatment and taking out existingcracked plaster by manuallyor mechanically and wire brushingandcleaningtheexistingsurface with water complete all as specified andas directed by the engr in charge. , dismantling water tank and removing to store of 2000 litrs capcity ( upto 12 storey high of building ) , dismantling wrought iron or mild steel work of any description not otherwise provided for , m&l for pvc perforated sheet 6mm thick, rounded hole of dia 12mm staggered type c / c spacing 25mm with ms frame ( size 40x40x5mm thick ) fixing on beam and column with nut and bolt of required size including dismantling of old rcc jallies upto four storied of building complete all as specified and as directed. ( upto 04 storey high of building ) note: shape / design of jallies as appoved by ge ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , m & lfor cutting chases, pinning, in making good to facing where required of of brick wall and pointing in cement motrar 1:3 to ends and cutting chases for concealed water tubing and concealed conduit wiring ete and making good surfaces , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , cutting holes in brick work for inserting hold fast etc including making good the adjacent area with cement and sand mortar 1:3 or pcc 1:2:4 type b, as required at site complete all as specified depth of embedded potion of hold fast or legs measured from the face of the jamb into the wall exc half brick but n. exc one brick ( upto 04 storey hight of building ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f in repair towel rail of brass chromium plated tube 19 to 20 mm dia 600 mm long `d type complete fixed in repairs with brass chromium plated screw complete all as specified and directed. ( upto 04 storey hight of building ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f for powder coated aluminiumsliding windows for ( three tier ) withwith shutter styles 40mm x 20 mm sheet thickness 1.5 mm two shutter glass and one shutter of wiremess consisting of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples, frame ( chowkat ) of window shall 100 mm x 44 mm x 1.5 mm thick section with or without rebate including5 mm thick tinted glass fixed with aluminum beads locking arrangements with each shutter incl aluminum grillcomplete in all respect as specified ( upto 04 storey hight of building ) , all as per item no above but 5 storey to 8 storey , all as per item no above but 9 storey to 12 storey , materials and labour for providing and fixing anchor fastener system machanical / epoxy for connections in concrete i / c power drilling, cleaning of holes by air blowing, insertion of epoxy cartridge with plastic nozzles as required, placing internally threaded screw driving of bolts etc. upto to 10mm dia bars and upto twelve storied building complete all as specified and as directed. , s&f powder coated aluminum fixed partition wall as faced of stair case and balcony of framesize 64mm x 38mm x 1.55 mmwithstandard beads / glazing clips, locking arrangement etcwith necessary all fittings including5 mm thick tinted glass fixed with aluminum beads locking arrangements with complete all as peranufacturers instructions and all as specified and as directed by the engr in charge.up to 4 storey bldg , all as item no. above but from 5 storey to 8 storey of building , all as item no. above but from 9 storey to 12 storey of building , m& l for 15mm thk screed bed in cm ( 1:3 ) with waterproofing compound for laying of app membrane complete all as specified andas directed by the engr in charge. ( upto 12 storey high of building ) , applying evenly a tack coat of in 1.2 kg per sq.m including cleaning surfaces complete all as specified andas directed by the engr in charge. ( upto 12 storey high of building ) , s&l3mm thickprefabricatedplastomericwaterproofingmembrane ( polyster rainforced ) withspunbondedpolystermatas a core ( app membrane ) ( weightnot lessthan 3 kgper sqm ) laidoverbituminouscoatedsurface ofroofandapplied withlpgtorchandapplyinguniformpressurewitha roller / wetclothto ensureto removeentrappedair, ifanyallas permanufactureerinstrucction .the appmembraneshallbeoverlapof notless than100mmand150mm as end lap andsidelaprespectivelysas permanufacturerinstruction .theover lapingandjointswill bethermosealedwiththepropanetorchcomplete all as specified andas directed by the engr in charge. ( upto 12 storey high of building ) , m& l for cement concrete tiles 25cm x 25cm x 22mmthick, machine pressed tiles, set jointed and pointed in neat cement slurry on roof over and including 15 mm thick bedding layers in cm 1:6, cut and finished neatly and polished etc and complete all as specified. ( upto 12 storey high of building ) , supply and fix rotational moulded pvc water storage tank 2000 ltr capacity ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i. ( upto 08 storey high of building ) , disconnectingexistingwatertank, settingaside forcleaning& removing scaleanddirt andthe sameof size exc 1000 and n.exc 2000litres. ( upto 12 storey high of building ) , s&ftoilet paper holder fixed in repairs to wall with chromium plated brass screws complete all as specified and as directed. , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , supply & fixing in repair wash down water closet ( pedestal pattern ) including connection to drain ( or outgoing pipe ) and to flushpipeetc.and making good the damaged surfaces complete all as specified and as directed by the engr in charge. upto 4 storey of building , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f pvc water closet seat cover heavy duty coloured closed pattern with flat bottom and cover and mild steel cp hinnging device complete. , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f brass cp soap dish, fixed with brass screws or embedded in wall.or equivelent. , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete in all respect as specified upto 4 storey , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f in repair brass cp wall mixer with half or qtr turnfor mixing hot & cold water screwed down for iron pipeand fixed for upto 4 storey , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f in repair wash hand basin mixture brass cp tap for mixing hot and cold water with qtr or half turn including three joints to 15 mm bore pipes or union and pluging and screwing to wall complete fixed in repair.upto 04 story , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&fsheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long ( upto 04 building ) . , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm and including 32mm waste coupling of ptmt ( half or full threaded ) minimum weight 32mm 45gms / 40mm 60 gms ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , supply and fixin repair for curtain rods dicorative aluminium alloy with fixing brackets including taking down old pelmet box complete all as specified. ( upto 04 storey hight of building ) , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , supply and fix bracket dacorative type for curtain rods aluminium alloycomplete all as specified. , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f for framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screws including bending and welding angles as necessary, gusset plates, riveting, etc n, exc 10 kg each brackets confirming to fe 290. grade e 165 ( brackets over 10kg each to be measured under structural steel ) upto four storied building complete all as specified. , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s&f for pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering / cladding to wall, fixed with self taping screw upto four storied building complete all as specified. , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , supply & fixing in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with ss wire staples complete, all as specified and directed.complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s& fix in repair prelaminated particle board 18 / 19 mm, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in cup board for short area complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , s & f 2 mm thick wall care putty on wall ( in two layers ) complete all as specified and as directed by engineer in charge. ( upto 04 storey high of building ) , all as per itemabove but 5 storey to 8 storey , all as per itemabove but 9 storey to 12 storey , supplying and fixing1.25mm thick steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual typecomplete all as specified and as directed. , s&f lock plate bracket made of angle 40x40x5 mm, flat 25x6 mm, cleat, latice flat & locking arrangement etc of rolling shuttes including necessary welding / riveting and one coat of red oxide primer including taking down old lock plate complete all as specified and directed. , providing anti termite ( post construction ) along the external wall below concrete or masonary apron using chemical chloropyritphos 20 ec or linane 20 ec ( isi marked ) emulsion@ 2.25 literes per linear meter including drilling and plugging holes etc in aprons / plinth protection , complete all as specified and directed by engineer in charge. , providing anti termite ( post construction ) of soil under existing floors using chemical chloropyritphos 20 ec or linane 20 ec ( isi marked ) emulsion @ one leter per holes , 300 mm apart along thejunction of floor and walls including drilling and plugging 12 mm dia holes with cement mortar 1:2 ( 1 cement : 2 coarse sand ) to match the existing floors. , providing anti termite ( post construction ) of voids in masonary using chemical chloropyritphos 20 ec or linane 20 ec ( isi marked ) emulsion @ 1.00 liter per holes , at 300 mm intervals including drilling 6 mm dia holes at downward angle of 45 degree and repluging the holes with cement mortar ( 1:2 ) to match the existing surface , complete all as specified and directed by engineer in charge. , providing anti termite ( post construction ) at the point of ontact of wood work by chemical emulsion ( in iol or kerosene based solution ) @ 0.50 leter / holes by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre angle of 45 degree at 150 mm centre to centre and sealing the same, , s&f corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 300mm long complete all as specified and directed make prayag or equivalent ( upto 04 building ) . , ditto all as item no. above but from 5 storey to 8 storey of building , ditto all as item no. above but from 9 storey to 12 storey of building , s & f plywood for moduler kitchen, grade bwr, type bb, fixed with screws to timber frame work 19 mm thickincl all necessary fittings complete in all respect as specified , s & f decorative laminate 0.9 mm thick type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete in all respect as specified , s & f ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixedcomplete in all respect as specified , s & f 75 mm butt hinges stainless steel, and fixedincl all necessary fittingscomplete in all respect as specified , s & f brass handles 100 mm length, cast type, polished brightincl all necessary fittingscomplete in all respect as specified , m & l 2nd class hardwood plain fillets.square, rectangular or triangular in section, clean sawn, secured with nails or brads not exc 3 sqm complete in all respect as specified , dismantling and taking down point wiring ( light, fan, socket and power complete including fixtures andfittings such as switches ceiling roses, pendents , regulators, sockets, light fittingsetc. removing materialsfor taking credit ( credit for above items should be made as per conditions separately ) and making good distrubed surfaces of walls, floors, etc. , m&l for point wiring with pvc insulated unsheathed stranded copper conductor cable frls of size 1.5 sq mm with proper colour codingand including concealedpvc conduit 20 mm dia medium duty isi marked with all necessary fittings for mounting of modular switches / sockets including 1.5 sq mm pvc insulated unsheathed stranded copper conductor as earth lead and connected to common earth dolyfor one light / ceiling fan / exhaust fan controlled by one switch complete including cutting, chasing the surface on walland then making good the same in cm 1:3 complete all as specified and directed by engr in charge. make of wire : finolex / havells / kei industries ltd make of pvc conduit and fittings : bec / prestro / avon plast / finolex , all as per item no. 2 above but of one bell point controlled by one bell push with cables of 1.5 sqmm size , all as per item no.above but 3 pin 5 amps socket out let point with the same board with other switches with cables of 1.5 sqmm size , all as per item no.above but for one 5 amp socket on independent board with cables of 1.5 sqmm size , all as per item no. above but using2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board complete all as specified and directed by engineer incharge. , all as per item no.above but for one light point controlled by two switches two ways. , s& f sunken flush metal gi boxes for fixing of modular switches / sockets flush to the walls complete for 2 modules. , do all as per item noabove but for 3 modules , do all as per item no above but for 4 modules , do all as per item noabove but for 6 modules , do all as per item noabove but for 8 modules , s&f modular cover plate with frame for fixing of modular switches / sockets complete for 1 modules ( note: switch and sockets will be measured and paid separately ) , do all as per item no. 13 above but for 2 modules , do all as per item no. 13 above but for 3 modules , do all as per item no.13 above but for 4 modules , do all as per item no. above but for 6 modules , do all as per item no.above but for 8 modules , s&f switch modulartype 6 amps 230v ac complete one way , s&f switch modulartype 6 amps 230v ac complete two way , s&f modular bell push5 amps. , s&f for modularsocket outlet 3 pin 5 amps 230 volts . , s&f modular socket outlet multipurpose 3 pin 16 amps and one6 amps controlled by one switch. , supply and fix modular type switch, one way 16 amps, 1 module complete all as specified and directed. , s&f modular electronic step type fan regulator 230 volt , 2 module . , s&f polycorbonate / pvc ceiling rose of size65x50mm single phase , s&f call bell, musicalac 230 volt single pole. , supply and fixing led lights fitting 1x 18 20 w, 220v, ac decorative box type aluminimum extruded, with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.all as directed. make : crompton cat no : ccs 100 20 65 hl2 dp nwh bajaj cat no : bclab 20w led p s havells cat no : lumiline+bs20wled830spcss , supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 9 12 watt 220 v ac decorative type aluminium exturded with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete make :crompton cat no : ccs 102 10 65 sl dp nwh philips cat no : cat no bn021led12s6500 psu havells cat no : lumiline+bs10wled865spcss , supply and fixing decorative type led wall bracket light fitting having chromium plated steel body , frosted glass defuser, suitable for 7 10 watt led lamps complete all as specified and directed. make : lukar cat no : lwl112 1 havells cat no : lhfoece1tz10014 stylo or equivalent , s&f ac starter unit consisting of one 25 amp capacity starter, one 240 v 25 amps 10 ka spn mcb, one 25 amps socket and one 25 amps plug top prewired including taking down complete all as directed. make : crabtree / legrand / anchor / abb , taking down unserviceable rusted / damaged mcb dbs of any type and way along with any type mcb and keeping serviceable mcb in safe custody in re use in the work and making good to the distubed surfaces of walls etc. complete all as specified and as directed. , s&f mcb tpn db made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail, 4 way with 200 amps rated bus bar, 415 volts complete all as specified and as directed. , s&f mcb spn db made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail, 4 way with 200 amps rated bus bar, 230 volts complete all as specified and as directed. , s&f mcb sp 5 32 amps 230 volts 10ka breaking capacitycomplete all as specified , s&f mcb spn 40 63 amps 230 volts 10ka breaking capacitycomplete all as specified , s&f mcb tpn 63 amps 415 volts 10ka breaking capacitycomplete all as specified , taking down aluminimum sub mainwiring alongwith damaged casing capping / pvc conduit pipe from the wall roof or in floor and making good disturbuted surfaces complete all as directed , s&f sub main wiring with proper colour coading 4 run of single core pvc insulated unsheathed stranded copper conductor frlsof size10 sqmm & 2 run of pvc insulated unsheathed stranded copper conductor of size 10 sqmm as earth lead drawing into rigid non metalic pvc conduit of suitable size isimarked including taking down old unsv. note: four run of 10sqmm cable and two run of 10 sqmm earth cable will be measured as single length. ( from tpn to meters ) , all as per item no. above but with two run of single core 6 sqmm and one run of 6 sqmm cable complete ( from meters to dbs ) note: two run of 6 sqmm cable and one run of 6 sqmm cable will be measured as single length , all as per item no. above but with two run of single core 4 sqmm and one run of 4 sqmm cable complete. ( for two nos of acs at each qtr ) note: two run of 4 sqmm cable and one run of 4 sqmm cable will be measured as single length , supply and fixing 5 star rated water heater ( geyser ) storage type energy efficient sphp technology inner container , a.c single phase 230 volt, 50 hz of storage capacity 25 ltrs vertical type complete connecting upwater heater , including fixing of hold fast 10 cm long including washers completeincluding dismanling of old unsv geyser from its existing position as specified note : old dismantled unsv geyserswill be deposited to mes store of age e / m ii at turf view for further disposal under departmental arrangements. , supply and fixing five star rated with brushless direct current motor ( bldc ) ceiling fans 1200 mm sweep complete with blades, down rods, electronic regulator and accessories, 230 v, min air delivery 210 cfm with service value 6.00 bee completeincluding dismanling of old unsv ceiling fan from its existing position all as specified and directed. note : old dismantled unsv ceiling fanswill be deposited to mes store of age e / m ii at turf view for further disposal under departmental arrangements. , supply and fixing five star rated with brushless direct current motor ( bldc ) ceiling fans 1400 mm sweep complete with blades, down rods, electronic regulator and accessories, 230 v, min air delivery 245 cfm with service value 6.00 bee completeincluding dismanling of old unsv ceiling fan from its existing position all as specified and directed. note : old dismantled unsv geyserswill be deposited to mes store of age e / m ii at turf view for further disposal under departmental arrangements. . , supply and fixing wall mounted fan 300 mm sweep, voltage range 220v to 230 volts, 50 hz, single phase complete with speed regulator and oscilator with pulling threads complete as directed. , supply, installaion , testing and commissioning electric kitchen chimney , auto clean type with baffle filters, minimum length 90cm ( suitable for 3 to 5 burner stove ) with suction capacity 1425 m3 / hour ( min ) including exhaust duct with alll fixing accessories and making hole on the wall for passing the exhaust duct complete all as specified and directed. , supply and fixing exhaust fan 250 mm sweep, with polycorbonateblades 230 volts 50 hz single phase including louvres & shutters nuts and bolts completeincluding modification of existing hole ( if required ) all as directed..make:havells or equivalent in bajaj / cg note : old dismantled unsv exhaust fanswill be deposited to mes store of age e / m ii at turf view for further disposal under departmental arrangements. , s & fin repair led luminaire 600 mm x 600 mm, 34 36 watt, 220 v ac surface type with high efficiency pmma diffuser soft glare free light complete with inbuilt driver, suitable for roof ceiling including connecting up with driver three core flexible copper conductor wire of suitable size complete all as specified and as directed by the engr in charge. ( for lift lobby ) make : crompton cat no : lctlsne 36 fo cdl havells cat no plutosurface2x2pls34wled857s bajaj cat no bzssql 36lled whgx , taking dlown carefully the existing led light batten fitting of any wattage 20 / 10w and any size by unscrewing from wall / outlet boxes and fixture and keeping in safe custodyfor refixing the same after completion of new wiring workand complete all as specified and as dircted by theengr in charge ( note : any breakage / damage of light fitting during taking down / refixing shall be make good by the contractor with his own cost ) , supply and fixing fire alarm control panel 8 zone complying with is 2189, micro controller based with 32 character lcd display , inbuilt battery charger and battery with inbuilt common hooter connection pointincluding taking down of existing unserviceable one complete all as specified and directed. , supply and fixing fire alarm control panel 16 zone complying with is 2189, micro controller based with 32 character lcd display , inbuilt battery charger and battery with inbuilt common hooter connection point including taking down of existing unserviceable one complete all as specified and directed. , supply and fixing manual call point resettable type ms body red in colourincluding taking down of existing unserviceable one complete all as specified and directed. , supply and fixing hooter ms body red in colour including taking down of existing unserviceable one complete all as specified and directed. , supply and fixing control wiring of mcp and hooter with 2 runs of 1.5 sqmm pvc insulated frlsh copper conductor wire in pvc casing caping of suitable sizeincluding taking down of existing unserviceable wiring complete all as specified and as directed. , dismantling , supply and fixing single pointed air termination rod of 12mm dia and 600mm longcomplete all as specified and as directed by the engr in charge. , dismantling , supply and fixing single aluminium strip 25x3.15 mm complete with saddles and fixing screws for roof conductor / down conductors all as specified. including pocelain insulatorcomplete all as specified and as directed by the engr in charge note : rate quoted shall deemed to be inclusive of scaffolding etc in high rise buildings , dismantling , supply and fixing earth continuity conductor 32x6mm gi strip or main earthing lead fixed to wall on batten or recess or buried in ground or drawn in conduit / pipe or fixed to pole or any other indicated situation for loop earthing etc. complete all as specified and as directed by the engr in charge. , dismantling , supply & laying gi tubing light grade fixing for lightning conductor of40mm bore complete all as specified and as directed by the engr in charge. , dismantling , supply & laying gi tubing light grade fixing for lightning conductor of80mmbore complete all as specified and as directed by the engr in charge , dismantling , supply and fixingtest point terminal box made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw including taking downcomplete all as specified and as directed by the engr in charge....

Indian Army - West Bengal

38394724 spare parts for ssl eng , alluminium alloy gde 64430 r/bar dia 80 part no , steel plate carbon h/r 2200 x 900 x 8 mm part no => limited...

South Eastern Railways - West Bengal

38381961 supply of torque wrench dremometer dz 140 620 nm to model no. gedore 7703020 or bosch or hazet or stahwille or mac master with following features. ( 1. ) end fitting torque wrench 140 620 nm with 17mm allen end fitting suitable for it. ( 2. ) light weight yet robust ( 3 ) . the housing is made of aluminium alloy and resiliant ( 4 ) . extremely low wear attributable to reduced forces in the lever mechanism ( 5 ) . working accuracy + / 3% ( 6 ) . product length 846mm weight 3kgs note: 1 ) .item shall be supplied along with manufacturer test certificate and warranty certificate.2. ) firm should submit authorised dealership certificate along with tender or proof of purchase from authorised dealer shall be submitted along with supply [ warranty period: 30 months after the date of delivery ] ...

Metro Railway - West Bengal

38355847 supply of aluminium / alloy trolly ladder platform height 8 ft. overall height 10 ft. with 1. load carring capacity 200 kg, 2. chain & lock for locking arrangement. 3. rubber wheel with break to immobilize when in use as per drawing no. al 7600a enclosed [ warranty period: 30 months after the date of delivery ] ...

Indian Army - West Bengal

38351311 bids are invited for purchase of spares l1 chokes small 2 anchor bridging 60 lbs 3 rivet aluminium alloy round hd 4mm x 10 mm long4x1 4 cover water protection canvas boat assult universa 5 bailer fbe 6 spike bridging ( impd 0543 ) 7 bag canvas for life jacket 8 stop rubber 9 screw driver engineers 150 mmlg 10 pin lock bottom link side 11 dolly rivetting for 4mm dia rivets 12 box repair kit 13 pin taper solid steel 6mm x 30 mm 14 paddle timber 1.2 m long 15 chock wheel 16 oars 3.05 mtr long ( 10 ft ) 17 buoys anchor 18 cap detachable nylon for pin pivot 19 life jacket ( preserver waist coat ) 91 cm / 36 in 20 keel / keel assy / keel in 3 parts 21 rope manila howserlaid 3 strands 64 mm dia 7.5 m l 22 cordage nylon 12 mm dia 10m long 23 needle sail markers triangular sewing 24 valve air 25 slotted round head 26 sealant 2 mtrs long 27 rowlock with chain 28 screw machine csk hd bm 8x 9 on 29 scissors flat 250 mm 30 adhesive ad 94 with cla swastik 0.25 litre tin 31 foot pump double nozzle 32 toggle wood 33 rope nylon 12mm x 5m 34 paper sand rough no zero 300x300mm 35 chalk french ( 60 grams packet ) 36 crucible plastic cup 100ml 37 valve air 38 bag canvas accessories 39 life jacket 40 inch 40 fabric, nylon, neoprene coated 0.13kg / 275mmx1030mm 41 grating 42 bag for boat recce 3 men 2a 43 valise floor assy frp 44 valise kit repair 45 valve diaphragm stop air inflation / deflation 46 floor board assemble frp 47 paddle boat 1600mm long 48 pin mooring 320mm long with cordage 15mm x 12 mtr 49 bailer boat 50 valise boat assualt pneumatic light weight a 51 valise accessories 52 spatula wooden 4mm thick 20mmx170mm long 53 foot pump ( single nozzal with 1.5 mtr long ) 54 cross linking agent in aluminium btl with separate total quantity : 1146...